原油基压裂液研究

研制了一种适用于低压、低渗、水敏性储集层的新型原油基压裂液体系。根据基液原油的组分合成相应的增稠剂，增稠剂在原油中与交联剂反应，形成网状结构，使原油成为黏度可以调控的冻胶，从根本上改变了油基压裂液以柴油、煤油为基液的现状，降低了油基压裂液的成本，同时还提高了压裂液的抗温、抗剪切和破胶性能，并将交联时间缩短到2h以内，可以满足现场压裂施工的要求，大大降低了施工强度和压裂改造的综合成本。在青海油田进行的现场先导试验取得成功。图9表1参5     

Structural changes in isothermal crystallization process of polyoxymethylene investigated by time-resolved FTIR, SAXS and WAXS measurements

Structural evolution in the isothermal crystallization process of polyoxymethylene from the molten state has been investigated by carrying out the time-resolved measurements of infrared spectra and synchrotron small angle X-ray scattering (SAXS) and wide angle X-ray scattering. In case of isothermal crystallization at 130 °C, for example, the infrared bands intrinsic of folded chain crystal (FCC) morphology appeared at first, and then the bands of extended chain crystal (ECC) morphology were detected with time delay of ca. 150 s. In the SAXS experiment at 130 °C, the lamellar stacking structure of the long period of ca. 15 nm was observed at first, which changed rapidly to ca. 12 nm in a short time. The SAXS peak with the long period of ca. 6 nm started to appear with a time delay of ca. 150 s after the initial lamellae appeared and coexisted with the initially-observed 12 nm peak. Judging from the timing to detect these characteristic infrared and SAXS signals, a good correspondence was found to exist between the stacked lamellar structure of 12 nm long period and FCC morphology and between the structure of 6 nm long period and ECC morphology. The quantitative analysis was made for the SAXS data on the basis of the lamellar insertion model combined with the paracrystalline theory of the second-kind of disorder. The following structural evolution was deduced from all these results. Immediately after the temperature jump from the melt to 130 °C, the stacked lamellar structure of FCC morphology was generated at first. New lamellae were formed from the amorphous region in between the originally-existing lamellae about 150 s later, where the random chain segments bridging the adjacent lamellae were extended to form the taut tie chains, giving infrared bands of ECC morphology. This inserted lamellar structure of 6 nm long period coexisted at a population of ca. 6% with the initially-formed lamellar stacking structure of 12 nm long period. When the experiment was made at 150 °C, only the formation of stacked lamellar structure of FCC morphology was observed and the insertion of new lamella did not occur.     

一种制氢预转化催化剂还原的新方法

对上海高桥分公司2×10~4m~3/h(标准状态)制氢装置原设计的预转化催化剂还原流程进行了改进。先跳开预转化反应器,利用转化炉制取氢气,再用自产的高纯氢气代替重整氢,对预转化催化剂进行单独升温还原,避免了催化剂在还原初期因发生甲烷化反应而超温失活的问题,使催化剂具有更好的活性和稳定性。     

丙烯醛制备1,3-丙二醇的中型试验研究

对丙烯醛水合、加氢制1，3-丙二醇工艺进行了中试研究，主要对小试技术的可靠性进行验证。结果表明，丙烯醛经水合、加氢制1，3-丙二醇的工艺技术可行，反应器、精馏塔等设备设计合理。中试丙烯醛水合单程转化率为45％～55％，3-羟基丙醛选择性达到了93％左右，3-羟基丙醛加氢收率接近100％，产品1，3-丙二醇的醛基质量分数降至5μg／g以下。与小试结果相比较，中试的水合选择性明显提高，加氢催化剂活性寿命延长。     

创建互联网业务价值链

为促进互联网的良性发展,要使设备制造商、电信运营商、虚拟运营商/集团用户、内容提供商和最终用户构成一条互联网业务价值链,价值链的创建对互联网接入设备提出了更高的要求,华为公司的Quid-wayTMA8010Expert多业务综合接入平台可构建宽带城域网分组语音解决方案、可平滑演进为下一代网络中的媒体网关、提供窄带价值链、提供唯一号码业务以及实现多业务综合接入。     

荧光显示管直丝氧化物阴极有效逸出功的计算

阴极的逸出功是表征阴极发射能力的物理量，求定荧光显示管直丝氧化物阴极有效逸出功时，因其零场发射电流密度难于准确取值，温度无法直接测量，显得困难，须予解决，为此提出了一种计算阴极有产逸出功的办法，对某显示管的发射欠佳和“低温高效”的两种氧化物阴极的有效逸出功进行计算，有效逸出功率是靠测量相关物理量再同计算得出，精度不很高，文中所用办法也不例外，但所得结果能反映阴极发射能力，所需仪器少，是实用方法。     

纳米级BaAl_2O_4微粉的制备和性质

分别用溶胶 -凝胶法、低温固相反应法 ,制得了纳米级BaAl2 O4微粉 ,用电镜观察了其形貌和粒径的大小 ,用X-射线衍射仪进行了物相分析 ,测定了其纯度与晶型 ,讨论了制备方法与粒度大小的相互影响     

甲醇氧化羰化制碳酸二甲酯产物气相色谱分析

以Chromosorb 10 1为固定相 ,气相色谱法分析甲醇氧化羰化制碳酸二甲酯产物中水、甲醇、乙酸甲酯和碳酸二甲酯等组份的含量 ,考察了柱温 ,载气流量对分离度的影响 ,确定了适宜的分析条件 ,并用校正面积归一化法定量。该方法操作简便 ,快速 ,精度高 ,重现性好     

功能化的介孔分子筛碱催化性能的研究

以苯甲醛与氰乙酸乙酯的Knoevenagel缩合为模型反应，研究了用γ－氨丙基三乙氧基硅烷或γ－乙二胺丙基三甲氧基硅烷功能化的纯硅介也分子筛HMS（Hexagonal mesoporous silica）的碱催化性能。结果表明，除个别碱基负载量高的样品外，功能化样品对反应显示很高的催化活性，反应的初期活性不仅取决于催化剂上活性中心的密度，而且与载体的孔道结构有关。大孔径载体有利于反应物、产物的扩散，故在高负载量时，大孔径样品比小孔样品有更高的活性。此外，还考察了反应温度、溶剂、反应物配比和催化剂用量等条件的影响以及催化剂的重复使用情况。结果表明，反应可在低于100℃的温和条件下进行，有明显的溶剂效应，反应物配比和催化剂用量存在一最佳值；随使用次数的增加，催化剂逐渐中毒而失活。