Spray forming: Science and technology

Spray forming involves sequential gas atomization of a melt into a spray of fine droplets and their deposition on a substrate to build up a high-density preform. The rapid solidification inherent in spray deposition generates refined, equiaxed and low segregation microstructures. A number of promising features of this near-net shape manufacturing process are highlighted and compared, wherever possible, with the conventional casting and PM techniques. Some commercial nozzles used to create spray and mechanisms associated with spray generation are described. The consolidation of the droplets and the development of the microstructure in the deposit are primarily governed by the nature of the spray and the thermal state of droplets on the deposition surface. Several microstructural characteristics of the deposit are presented and their origin in spray deposition is discussed.     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

阵列天线在OFDM系统下行链路中的应用

正交频分多址(OFDM:orthogonal frequency division multiplexing)技术由于其在多径环境下克服码间干扰的固有特点,在移动通信中已得到广泛地应用。利用阵列天线上行链路信号到达角估计实时信息,计算OFDM系统下行链路阵列天线权重,将阵列天线应用于下行链路中,最后给出系统误码率性能的计算机仿真结果。     

塔河油田S105井-S106井-S117井井区盐下奥陶系油气成藏条件分析

为了探索塔河油田石炭系盐下奥陶系储集层发育特征及成藏条件,实现新地区、新层位、新领域的突破,进一步扩大塔河油田外围盐下奥陶系含油气范围,实现增储上产,利用率先在盐下奥陶系完钻的S105井、S106井、S117井的地质录井、测井、测试等资料,结合区域地质资料,对S105井-S106井-S117井区内盐下奥陶系的区域构造特征、油源条件、储集条件、储盖组合、圈闭条件及油气藏类型进行了分析,得出的结论是盐下奥陶系恰尔巴克组-一间房组发育地层不整合-岩溶裂缝型圈闭,且油源充足,储集层发育,圈闭条件良好,易于油气成藏,指出了盐下奥陶系的勘探开发前景。     

内外齿复合冷挤压成型实验研究

通过对轿车转向盘毂件内外齿进行的复合挤压实验研究 ,得到了新式复动式复合挤压模具结构 ,并确定了一种合理的成型工艺方案     

枣35断块沙三段玄武岩储层特征及成藏条件分析

从地质、地震、测井及试油试采等方面入手，并采用新技术，对自来屯构造枣35断块沙三段玄武岩储层特征及成藏条件进行了分析。其结果为该区下一步勘探、开发及进一步研究奠定了基础。     

关于粉体成球机盘体几何形状的研究

通过对粉体小球在粉体成球机盘底上运动轨线的研究,利用Euler定理,结合其参数特点,得到了不同几何形状的盘底在成球过程中对粉体小球运动的影响,球面盘底较平面盘底更有利于成球的结论。     

五号桩洼陷沙二段隐蔽油藏成藏规律研究

从成藏条件的构造、沉积条件分析入手,研究了五号桩洼陷内沙二段储集层的沉积相类型,总结了沙二段隐蔽油气藏成藏规律和分布模式,并部署了3口探井和7口滚动开发井,发现了3个含油断块,新增石油地质储量203×10~4t,为该区下步勘探指明了方向。     

翻领成型器领口曲线的程序计算展开法

根据翻领成型器领口曲线的数学模型，介绍一种利用计算器复杂公式存贮的特殊功能，预编程序计算相关参数。然后画领口曲线展开图的方法。     

变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。