平面波谱法分析电磁波在管道中的传播

通过分析电磁波从管道开口耦合进入管道的绕射机理及场在腔体内的射线特征，将进入管道的绕射场展开为平面波谱，利用平面波在自由空间的传播特性分析了电磁波沿管道的传输和反射特征。通过算例验证了该算法的有效性。     

翻领成型器领口曲线的程序计算展开法

根据翻领成型器领口曲线的数学模型，介绍一种利用计算器复杂公式存贮的特殊功能，预编程序计算相关参数。然后画领口曲线展开图的方法。     

变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。     

工业产品的艺术造型与技术美学

本文从技术美学的角度，广义的介绍了工业产品艺术造型的基本方法，着重从美学原则和色彩设计两方面论述产品造型设计的手法，以及技术美学在产品造型设计中的基本应用。     

Nd：碲酸盐玻璃的光谱和激光性质

对比了各种激光玻璃的光谱性质，指出碲酸盐玻璃是一咱理想的激光介质，并资产在室温下实现了钛宝石激光器泵浦了Ｎｄ：碲酸盐块体玻璃的激光发射，激光阈值４．２０ｍＪ，斜率效率１４．７％。     

Effect of Forming Pressure on the Internal Structure of Alumina Green Bodies Examined with Immersion Liquid Technique

Green bodies prepared by compaction of alumina granules were made transparent by an immersion liquid technique, and the internal structure was characterized with an optical microscope to study the effect of forming pressure on the internal structure. Clear images obtained by the technique provide more detailed information than other existing methods for structures ranging from one to tens of micrometers. Intergranular pores were present between unfractured granules. Their sizes and concentration tended to decrease with increasing forming pressure. However, pores were clearly present even in the green body prepared at 600 MPa. A rod- and needlelike feature was also found and was concluded to correspond to a high-density region. The significance of large pores and high-density regions on processing as well as the details of the technique is discussed.     

圆锥形零件冲压变形与成形载荷的分析

由于悬空侧壁部分的变形状态是圆锥形零件成形的关键，而径向拉应力是实现悬空部分成形的必要条件，同时也是该部分冲压成形成败的关键为此，经力学分析得出了侧壁部分径向拉应力的解析式和造成圆锥形零件破裂的最大径向拉应力的计算式。同时分析了圆锥形零件的成形载荷。     

New Technology for Producing Molybdenum Wire Billets

On the basis of systematic studies of intense methods for metal forming, a production scheme has been developed, substantiated by experiment and realized for manufacturing molybdenum wire. The main stages are helical rolling of small rounded bars, vibratory drawing with induction heating of wire billets, and cold wire drawing with hydrodynamic introduction of lubricant and application to the tool of vibration in the transitional stages of the process (start-up, speed-up, slow-down, and stopping the pulling tool drive).     

采取具体措施 发挥教研室的职能作用

本文就如何发挥高校教研室的职能作用记述了本教研室所采取的具体方法和措施。     

大庆油田水平井分流压裂技术

水平井分流压裂的技术原理是将水平井的水平段分成若干个单元，在每个单元的最佳部位进行射孔，每段的射孔数由孔径、单元数、设计施工排量等参数决定，射孔方案为压裂方案的有机组成部分。大庆油田已有5口水平井实施分流压裂，根据油层厚度分为两类：裂缝限制在油层内和裂缝穿透隔层贯穿多个薄油层。通过肇57-平35井和肇57-平33井进行的分流压裂贯穿多个油层现场试验，介绍了大庆油田水平井分流压裂的设计方法、压裂液体系、现场施工控制方法和效果分析方法。微地震裂缝监测结果表明，在最大施工排量7．5m^3／mim条件下，一次施工形成3～4条裂缝，加砂量最大达到75m^3（陶粒），平均砂比达到35％以上。水平井采用分流压裂技术施工后，初期产能可达到相邻直井压裂后产能的2．0倍以上。如何检测裂缝是否穿透了隔层并贯穿多个油层，是指导水平井分流压裂技术的选井选层，提高压裂效果的关键技术。图8表2参2。