基于MSP430F2274的无线数据采集节点的设计

介绍基于MSP430单片机为处理器的空气温湿度及光照度采集模块的硬件结构及软件流程,模块可完成空气温湿度及光照度的采集、存储并通过无线模块nRF905实现数据的无线收发;具有集成化程度高、结构简单、功耗低等优点,适用于野外环境监测的传感器节点及便携式的多参数采集仪器中。     

小型钨丝电热原子吸收光谱仪的电源

随着对分析仪器的小型化、便携式需求的提高,钨丝电热原子吸收光谱仪在便携式分析仪器方面显示了很大的潜力.为进一步满足现场分析的需要,以单片机为芯片,为小型钨丝电热原子吸收光谱仪的空心阴极灯和钨丝电热原子化器设计稳定的一体化恒流电源;并编写PC机的控制软件,以USB或RS232方式与电源通信,方便控制空心阴极灯和钨丝电热原子化器电流,以及原子吸收过程.以此电路设计的小型钨丝电热原子吸收光谱仪对镉、铅、金和银的标准溶液测试结果为:检出限分别为(0.1,6.0,5.0,0.6)μg/L,相对标准偏差分别为8.2%,5.3%,6.0%和7.2%.测试结果表明:电源很稳定,达到了文献报道的钨丝电热原子吸收光谱的分析性能.     

无数据缓存的容错环形NoC

提出一种分层双组双环NoC拓扑结构,该结构中链路分为两组环网,其中有一组环网为主环,另一组为备用环网,用于NoC网络的容错.每组环网中包含一个控制环和一个数据环,控制环采用包的形式交换结点之间路由、链路错误和差错控制信息,数据环用电路交换方式进行数据通信.针对以上NoC拓扑结构,提出交换结点无需缓冲区的三级流水线结构,使得各个IP之间的数据通信延时最小.环网中采用时分复用和优先级相结合的机制,实现了公平路由和带宽的空分复用.仿真结果表明,该结构可以有效避免拥塞、死锁和饥饿,保证带宽充分利用,与理论分析一致.     

高精度二相混合式步进电机控制系统研究

在二相混合式步进电机数学模型的基础上,针对电机低速运行时的振动和噪声过大的问题,研究了正弦脉宽调制细分驱动技术,开发出一种新型的基于单片机的多细分二相混合式步进电机驱动器。该系统主要分为数字控制部分、GAL片逻辑综合信号处理单元、SG3525恒流控制电路、驱动功放电路、过流保护及反馈电路和系统供电电源模块等。系统采用专用集成芯片和可编程逻辑器件,以8位单片机AT89C2051为控制核心,实现恒流控制、正/反转运行、过流保护和多档位细分等功能。实验结果表明,系统硬件和软件设计合理可行,各项技术指标均达到了设计要求。     

Experimental and numerical investigation into the joule heating effect for electrokinetically driven microfluidic chips utilizing total internal reflection fluorescence microscopy

This paper presents a detection scheme for analyzing the temperature distribution nearby the channel wall in a microfluidic chip utilizing a temperature-dependent fluorescence dye. An advanced optical microscope system—total internal reflection fluorescence microscope (TIRFM) is used for measuring the temperature distribution on the channel wall at the point of electroosmotic flow in an electrokinetically driven microfluidic chip. In order to meet the short working distance of the objective type TIRFM scheme, microscope cover glass slits are used to fabricate the microfluidic chips. The short fluorescence excitation depth from a TIRFM system makes the intensity information obtained using TIRFM is not sensitive to the channel depth variation which ususally biases the measured results while using a conventional Epi-fluorescence microscope (EPI-FM). Therefore, a TIRFM can precisely describe the temperature profile of the distance within 100 nm of the channel wall where consists of the Stern layer and the diffusion layer for an electrokinetic microfluidic system. Results indicate the proposed TIRFM provides higher measurement sensitivity over the EPI-FM. Significant temperature gradient along the channel depth is experimentally observed. In addition, the measured wall temperature distributions can be the boundary conditions for numerical investigation into the joule heating effect. The proposed method gives a precise temperature profile of microfluidic channels and shows the substantial impact on developing a numerical simulation model for precisely predicting the joule heating effect in microfluidic chips.     

基于改进的基因表达式编程算法在作业车间调度问题中的应用

文章提出一种新颖的方法一改进的基因表达式编程算法来求解作业车间调度问题。作业车间调度问题是许多实际生产调度问题的简化模型,基因表达式编程算法结合了遗传算法和遗传编程的优点,具有更强的解决问题能力,对基因表达式编程算法进行改进使其在作业车间调度问题的应用上更加有效;最后应用一个实例来验证提出方法的有效性。     

基于支持向量机的特征提取方法研究

基因表达数据的一个重要应用是给组织样本进行分类。在基因表达数据中,基因的数量相对于数据样本的个数通常比较多;也就是说,可以得到变量数（基因数）远远大于样本数的数据矩阵。过高的维数（变量或基因数）将给分类问题带来极大的挑战。本文提出结合一种新的特征提取方法——非相关线性判别式分析方法（ULDA）和支持向量机（SVM）分类算法,对结肠癌组织样本进行分类识别。并同其它方法作了比较研究,结果表明了该方法的可行性和有效性。     

脱水过程中无核白葡萄转录组测序及膜脂降解代谢中关键基因的筛选

该研究以吐鲁番地区无核白葡萄为试验材料,在25 ℃常温和30 ℃热风干燥后,取失水25%、50%时褐变和未褐变的样品。利用转录组测序技术筛选出膜脂降解代谢相关的关键基因,并利用实时荧光定量PCR技术对其进行验证,研究结果显示,转录组测序共获得了11.63亿的clean data,当无核白失水50%时未褐变与褐变的相比,在快速脱水组筛选出718个差异表达基因,慢速脱水组2 259个。将上述基因进行GO功能富集和KEGG富集分析后,筛选出43个膜脂代谢相关的差异基因,归类于5种代谢途径。从已获得的差异基因中最终筛选出乙醛脱氢酶7B4（Aldehyde Dehydrogenase7B4,ALDH7B4）、双半乳糖甘油二酯合成酶1（Digalactose Diglycerol Synthetase1,DGD1）、脂氧合酶（Lipoxygenase,LOX）、磷脂磷酸水解酶2（Lipid Phosphate Phosphatase2,LPP2）、二酰基甘油激酶5（Diacylglycerol Kinase5,DGK5）、非特异性磷脂酶C4（Non-specific Phospholipase C4,NPC4）、磷脂酶Dα1（Phospholipase Dα1,PLDα1）7个膜脂代谢相关的关键基因,经qRT-PCR验证,基因表达趋势与转录组测序结果基本一致。结果表明,膜脂降解代谢相关基因表达量变化对无核白脱水褐变有一定影响。     

Influence of cryogenic coolant on turning performance characteristics: A comparison with wet machining

Machining of 17-4 Precipitation Hardenable Stainless Steel (PH SS) is one of the difficult tasks because of its high cutting temperatures. Conventional cutting fluids are used to overcome the high cutting temperatures, but these are not acceptable from the health and environmental sustainable points of view. Cryogenic cooling is one of the potential techniques to overcome such problems. In the current work, comparison is made of cryogenic turning results, such as tool flank wear, cutting forces (feed force, main cutting force), cutting temperature, chip morphology and surface integrity characteristics with wet machining during machining of heat-treated 17-4 PH SS. The result showed that in cryogenic machining, a maximum of 53%, 78%, 35% and 16% reductions was observed in tool flank wear, cutting temperature, surface roughness and cutting force, respectively, when compared with wet machining. It was also evident from the experimental results that cryogenic machining significantly improved the machining performance and product quality even at high feed rates.