A Survey of Inverse Surface Design From Light Transport Behavior Specification

Inverse surface design problems from light transport behavior specification usually represent extremely complex and costly processes, but their importance is well known. In particular, they are very interesting for lighting and luminaire design, in which it is usually difficult to test design decisions on a physical model in order to avoid costly mistakes. In this survey, we present the main ideas behind these kinds of problems, characterize them, and summarize existing work in the area, revealing problems that remain open and possible areas of further research.     

有机-无机复合肥生产工艺

随着社会经济快速发展和城乡环境的污染已日趋严重。根据有机肥、无机肥各自的优缺点提出有机-无机肥生产的新工艺。     

长输管道建设物流管理新模式——物资配送

长输管道工程是以线路管道与沿途站场为主要内容的建设工程,其物资配送有着不同于一般物流管理的特点,点多线长,且交通不便.文章结合西南成品油管道建设工程的物资配送实践,总结出长输管道物资配送的类型,并从机构设置、计划编制、台账和报表管理等方面介绍了物资配送的管理内容及经验,实践证明,这种物资配送方法不但使业主的物资管理人员大为减少,而且使长输管道工程的物资供应更加及时有序.     

异构数据的管理方法及异构数据源的集成研究

工程应用中软件工具的多样性和设计活动的分散性形成了大量异构数据。本文分析了传统的异构数据管理方法的不足，提出使用数据库系统的文件系统结合的管理方法。针对此方法下所形成的异构数据源问题，给出了基于J2EE规范的数据访问对象抽象工厂解决方案。     

浅议铝箔项目的给排水设计

通过铝箔项目的工程实例,详细介绍了铝箔项目给排水专业设计的主要构成,并总结了几点设计体会,可供有关专业设计人员借鉴、参考。     

提高油田集输系统可靠性的研究

应用现代可靠性理论,从设计、工艺、技术等方面对油田集输系统进行了可靠性探讨,提出了增强系统可靠性的措施。     

Final Drying of Whole Milk Powder in Vibrated-Fluidized Beds

Vibro-fluidized beds are widely used in drying sticky powders and agglomerated materials as milk powder. Using a vibro-fluidized laboratory scale dryer, this work is aiming at analyzing preliminarily the effect of its operational variables on the drying kinetics and characteristics of whole milk powder. The full-factorial design technique with three replications at the central point has been employed to generate data and correlations to quantify the effect of inlet air temperature, air flow rate, and vibration bed amplitude on the drying curves and the milk powder properties related to its faster reconstitution in water (as tapped density, Hausner cohesion ratio, agglomerate size distribution, and internal pore concentration). Results obtained are analyzed and discussed to identify the adequate operation condition for final drying whole milk powder in vibro-fluidized beds, assuring a high product quality.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Displacement Discontinuity Method for Fracture Mechanics Analysis of Reissner Plates: Static and Dynamic

This paper is concerned with the displacement discontinuity method applied to the shear deformable plates (Reissner’s and Mindlin’s theories) with cracks subjected to static and dynamic loads. Fundamental solutions of dislocation are derived using the Fourier transform method and the Laplace transformation technique. Boundary integral equations are presented in terms of rotations/displacement on the crack surfaces. The Chebyshev polynomials of the second kind are used to evaluate the integral equations with hypersingular kernels on the crack boundaries and determine the stress intensity factors at the crack tips. Comparisons are made with other numerical solutions to demonstrate the proposed method is accurate both for static and dynamic problems.     

连续式超临界流体萃取进卸料装置

概括了超临界流体萃取技术和包括连续式操作在内的超临界流体萃取装置的研究现状 ,提出了一种通过球形进、卸料器完成固相物料超临界流体萃取连续化进卸料的装置 ,介绍了该装置的结构和工作原理 ,给出装置中各主要部件的计算方法。