AgWC12C3的粉末粒度对产品密度的影响

粉末粒度对粉末制品的性能具有重要的影响,而这些影响主要通过改善材料的密度来达到。该文根据模拟粉末堆积模型,确定相对合理的粒度组成,并通过试验予以验证。     

Physical Properties Important to Electrostatic and Non electrostatic Powder Transfer Efficiency in a Tumble Drum

ABSTRACT: Popcorn was oiled and coated in a tumble drum nonelectrostatically and electrostatically with sugar, cornstarch, salt, cellulose, maltodextrin, all-purpose flour, whole-wheat flour, or soy flour. Particle size, density, flowability, and chargeability were correlated to transfer efficiency using regression analysis. Of the various methods to measure chargeability, charge-to-mass and adhesion improvement were the most significant. For nonelectrostatic coating, small, dense, free-flowing powders were most efficient. Small, free-flowing highly charging powders were most efficient for electrostatic coating. Percent improvement was the highest for the least efficient powders. The greatest benefit with electrostatic coating was for low density, highly charging powders with no effect of size.     

A methodology for investigating effects of cell size on operational flexibility in flexible manufacturing systems

There are two aspects to cell formation in flexible manufacturing systems, cell sizing or deciding on the optimum number of machines to be allocated to each cell, and then allocation of specific machines to each cell. Although the latter problem has been investigated extensively there is a paucity of published work on the former. This paper discusses the effects of cell sizing on operational flexibility.Operational flexibility is that aspect of flexibility that enables manufacturing systems to respond with speed and efficiency to changes in the manufacturing environment while maintaining an effective level of control.     

Influence of Two Salicylate Components on the Particle Size of an Oil-in-Water Emulsion with Nonionic Surfactants

This paper reports a study undertaken using techniques of static and dynamic light scattering to investigate the influence of sodium salicylate and methyl salicylate on droplet size of oil-in-water emulsions. The rates of changes were measured by determining the size and distribution of the oil droplet in the material. All emulsions showed a bimodal size distribution; the mean diameters and polydispersity were calculated from intensity. These data were analyzed with nonlinear regressions and bootstrap methodology. An amount of methyl salicylate component induced a decrease of mean diameter and standard deviation. On the contrary, sodium salicylate entailed the growth of all droplet populations and coalescence for the highest concentration.     

CH_4、CO_2与O_2制合成气的研究 Ⅱ工艺条件的影响

在固定床反应器中考察了１２％Ｎｉ－５％ＲＥ－２％Ｃｕ－２％Ｌｉ／Ａｌ２Ｏ３（ｍａｓｓ）催化剂在ＣＨ４、ＣＯ２与Ｏ２催化氧化重整制合成气反应中催化剂粒径、工艺操作条件（空速与温度）及原料气配比对反应的影响，确定了较佳的操作条件：催化剂粒径２０～４０目，反应最佳温度为８００℃，ＳＶ＝４×１０４ｍｌ／（ｇ·ｈ）。同时看到在不同的原料气配比的条件下该催化剂的活性亦很稳定，不仅达到了反应平衡，且产物Ｖ（ＣＯ）／Ｖ（Ｈ２）比有很强的调变性。     

粒界缓冲型展宽效应对PTC材料温度系数的影响

本文利用相变扩张理论分析了粒界缓冲型展宽效应对BaTiO_3系PTC陶瓷的介电系数及温度系数a_r的影响,指出了晶粒尺寸和温度系数的关系。     

Effect of harvesting time and fruit size on titratable acidity, soluble solid and distribution of limonin in Thai tangerine juice

The effect of fruit size and harvesting of Thai tangerine fruit ( Citrus reticulata , Blanco) at different growth stages, 8–12 months after fruit set, on the distribution of limonin in whole fruit as well as in the individual fruit parts and extracted juice was investigated. The highest limonin concentration was observed in seed, followed by albedo, flavedo, segment membrane and juice sacs in decreasing order. The limonin concentration in juice as well as in whole fruit was decreased when fruit was harvested 8–12 months of fruit set. Increasing harvesting time from 8 to 12 months showed corresponding decreases in the amount of limonin in flavedo, albedo and seed. There was a decrease in titrable acidity and increase in total soluble solid and total soluble solid/titrable acidity ratio of juice with a later than normal harvesting time. However, fruit size showed no effect on limonin content and other properties of juice extracted from tangerine.     

云母粒径对云母／聚丙烯性能的影响

研究了云母填充改性聚丙烯(云母/PP)中云母粒径对其性能的影响。实验结果表明:云母粒径越小使得云母/聚丙烯材料强度提高越大、断裂伸长率增加,加工流动性变好;同时也促进和有利于聚丙烯结晶过程中的成核作用。     

硼预淀积对自组织生长Ge量子点尺寸分布的影响

研究了以不同B2H6流量预淀积硼对UHV/CVD自组织生长Ge量子点尺寸分布的影响。在适当的生长条件下,得到了尺寸分布很窄的均匀Ge量子点,用AFM对量子点的形貌进行观察,Ge量子点尺寸的涨落小于±3%,量子点的水平尺寸和高度分别为60nm和10nm,密度为8×109cm-2。实验结果表明,通过预淀积硼表面处理,可以得到尺寸分布很窄的量子点,以满足量子点光电器件方面应用的要求。     

原料对铁合金冶炼过程的影响

介绍了铁合金冶炼时需要准备的原料，对不合格原料需要进行加工处理，达到合格粒度。并提出了影响铁合金冶炼过程有原料的粒度，配料称量，混合等重要因素。