钎焊温度对SiC/YG8接头微观组织的影响

在保温时间为5min、钎焊温度为940~990℃条件下,采用CuMnNi钎料钎焊SiC陶瓷与YG8硬质合金.利用金相显微镜、扫描电镜和能谱仪对接头的微观组织进行分析,研究钎焊温度对接头微观组织的影响.结果表明:在靠近SiC一侧生成一层带状反应层,主要由Cu基固溶体、硅化物、碳和碳化物组成;焊缝主要由基底Cu基固溶体以及Mn、Si、Co、Cu、Ni元素形成的化合物组成.随着钎焊温度的增加,焊缝的宽度减少,焊缝中心的Cu基固溶体基底减少,而化合物相增多.     

消除磨齿裂纹的工艺措施

介绍了磨齿裂纹的产生机理,给出了防止磨齿裂纹产生的工艺措施,收到了良好的效果。     

确保硬质阳极氧化硬度与厚度的探讨

硬质阳极氧化能使铝及铝合金获得耐蚀,耐磨、绝缘性好,硬度高的涂层、对航空航天产品具有使用价值,但其厚度与硬度不易保证,本文着重探讨这个问题。     

硬质合金刀具电解磨削工艺研究

阐述了电解磨削硬质合金刀具的原理、特点及工艺。并对其工艺机理及影响因素进行了探讨。     

30CrMnSiNi2A钢件镀硬铬的氢脆分析

本文叙述了用延迟破坏法试验超高强度钢(υb=1700MPa)不超过三次镀硬铬的氢脆情况。     

激光熔覆模压硬质合金粉末层的研究

利用液压机和简易模具直接将硬质合金粉末(25? 15%Co 60% WC)压制在碳钢基体上;采用大功率CO2激光器对预置层进行扫描,在一定工艺参数下得到了表面较为平整、无裂纹、与基体形成良好冶金结合的涂层;利用扫描电镜和显微硬度计对涂层进行成分、形貌和显微硬度分析.结果表明,在相对较软的涂层基体上分布着高硬度的条状碳化物及少量的鱼骨状共晶体.涂层的平均硬度达到56HRC.     

GRINDING RESIDUAL STRESS OF CEMENTED CARBIDE

Grinding residual stress in the surface layer of WC-6 Wt—％Co hard alloy was measured by means of X-ray diffraction. The effects of various grinding parameters and treatment processes on the stress were studied. By means of electrolytic etching, the stress distribution along the depths beneath the surface was measured. The relationship between the stress and the service life of the alloy is discussed.     

Effect of binder-phase modification and Cr3C2 addition on properties of WC-IOC0 cemented carbide

For production of fine-grained and corrosion-resistant tungsten carbide (WC) based cemented carbides, addition of chromium carbide (Cr₃3C₂) in small amounts is standard practice. No systematic study, however, has been made of the effects of large additions (maximum 6 wt % ) of Cr₃C₂ as a substitute for tungsten carbide. This study focuses on the effect of hard-phase substitution by C₃C₂ in WC-1OCo cemented carbide. An attempt is also made to modify the binder metal cobalt by partial or complete substitution of nickel. Specimens were prepared using the standard liquid-phase sintering process and were tested for sintered porosity, mechanical properties, corrosion resistance, and microstructural parameters. Results confirm the findings of earlier workers regarding grain refinement and improvement of mechanical properties upon the addition of small amounts (<2 wt%) of Cr₃C₂. Modification of the binder phase improves indentation fracture toughness and corrosion resistance. Addition of Cr₃C₂ independent of the binder type improves corrosion resistance.     

全球铝轧制工业概览系列综述之九——日本神户钢铁公司真冈铝板带轧制厂

对日本神户钢铁公司枥木县真冈轧制厂的方方面面作了较全面的介绍，并对神户钢铁公司与美国铝业公司的合资企业－－神钢－美铝铝业有限公司作了附带的描述。这两家企业都是从上世纪70年代以来新建的高起点、高水平、高标准、高质量的世界级的铝板带轧制厂，前者的建设时间历20余年，是一步一步壮大的，原来（1＋3）式热连轧生产线，后改为（1＋4）式的，还有进一步改为（1＋5）式的余地。这是一个综合性强的铝板带加工厂，除生产罐料处，还可生产各种热处理可强化的硬合金板带材。该厂可作为中国今后建设全新的大型现代化铝板带轧制工程的模式。     

稀土添加剂在镀硬铬中的应用

介绍了标准镀铬液中加入稀土添加剂进行低铬酸镀硬铬工艺及应用生产情况,以及取得的经济效益。