Phase Composition of Oxide Scales during Reheating in Hot Rolling of Low Carbon Steel

Low carbon steel was oxidized over the temperature range 1000‐1250°C in O₂‐CO₂‐H₂O‐N₂, O₂‐H₂O‐N₂, and O₂‐CO₂‐N₂ gas mixtures. Oxidation times were 12‐120 min. and the scales were 50‐2000 μm thick. The variations of these parameters were chosen to elucidate the phase composition of oxide scales under conditions similar to those of reheating furnaces in hot strip mills, using either thin slab casting or conventional casting and rolling technology. Two types of scales have been observed which are influenced by the furnace atmosphere, oxidation time, and temperature. The first type is a crystalline scale with an irregular outer surface, composed mostly of wustite (FeO), and a negligible amount of magnetite (Fe₃O₄). The second type is the classical three‐layer scale, composed of wustite (FeO), magnetite (Fe₃O₄), and hematite (Fe₂O₃). In general, the experiments showed that an increase in oxidation time decreased the percentage of wustite while the percentages of magnetite and hematite increased. A rise in oxygen concentration in the gas mixture increased the percentages of magnetite and hematite, confirming earlier experimental findings. In water vapour‐free atmospheres O₂‐CO₂‐N₂, the oxide scales had a low percentage of wustite, and high percentage of magnetite and hematite. Carbon dioxide showed a small influence at 1100°C, and a negligible one at 1250°C.     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

Green and self-lubricating polyoxymethylene composites filled with low-density polyethylene and rice husk flour

Polyoxymethylene (POM) composites filled with low-density polyethylene (LDPE) and rice husk flour (RHF) were prepared by injection molding. The POM/5 wt % LDPE/7.5 wt % RHF composite exhibited the lowest wear rate, whereas the coefficient of friction remained low, and the POM/5 wt % LDPE/5 wt % RHF composite had the best mechanical properties. X-ray diffraction analysis was carried out, and the worn surfaces were examined with scanning electron microscopy. The results showed that the addition of the filler reduced the crystallinity degree of the POM composites. The main wear mechanism for unfilled POM was adhesion, whereas for the POM composites, wear seemed to occur mainly by fatigue and abrasion. It was experimentally confirmed that the POM composite filled with LDPE and RHF, which is well-performing, low-cost, and environmentally friendly, could be a potential material for tribological applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of high temperature alkali cooking on the constituents,structure and thermal degradation of hemp fiber

Degumming of hemp fiber by high temperature alkali cooking was investigated, and the effect of temperature and dosage of alkali on the constituents, structure, and thermal degradation of hemp fiber was also discussed in this work. The morphology, structure, and thermal degradation of hemp fiber after high temperature cooking were investigated through SEM, FTIR, WAXD, and TG analysis. The results indicated that the high temperature cooking process was effective for removing hemicelluloses and lignin and could also improve the thermal stability of cellulose. Crystallinity index of the treated hemp fiber was increased, which was related to the cooking temperature and NaOH dosage. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Critical incidents and chronic stressors at work: Their impact on forensic doctors.

Workers in medium- or high-risk professions are often confronted with critical incidents at the workplace. The impact of these acute stressors may be serious and enduring. Many workers also experience chronic job stressors, such as work overload or role conflicts. This study examined the frequently neglected relationship of acute and chronic stressors with self-reported health symptoms, such as posttraumatic responses, fatigue, and burnout. This association was investigated in a sample of forensic doctors in the Netherlands (N = 84). It was found that the more traumatic events the respondents experienced, the more problems they reported in coping with the traumatic events. Chronic job stressors were associated with posttraumatic responses (intrusions and avoidances) and with burnout and fatigue. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

江苏复杂断块高含水单元改善水驱效果的技术对策

在分析高含水开发单元特点的基础上,针对该阶段剩余油的品位、分布和油水关系极为复杂、挖潜难度大的技术难点,提出了适合江苏复杂断块油田高含水开发单元改善水驱开发效果的思路和工作程序、技术对策,并在真武油田高含水开发单元进行了实际应用,取得了良好的效果.     

碳铬镍含量对高铬铸铁测温保护管性能的影响

通过高温氧化和高温磨损实验,研究了C、Cr、Ni 3个主要元素对高铬铸铁在高温条件下抗氧化和抗磨损性能的影响。结果表明:Cr含量越高,抗氧化性能和抗磨损性能越好;提高碳含量,明显提高高铬铸铁的高温抗磨性能;当w(Cr)=16％时,加入Ni能提高高铬铸铁的高温抗氧化性能;w(Cr)=30％时,Ni对高铬铸铁的抗氧化性能和抗磨损性能影响不明显.在1100℃以下,选用w(C)=2.8％,w(Cr)=30％、不加Ni的高铬铸铁铸造高温抗磨热电偶保护管,既有较好的使用寿命,又可降低成本.     

高强度钢板在汽车车身上的应用及问题对策

主要介绍高强度钢板使用量增加背景、已开发或正在开发的种类、高强度钢板在汽车车身上的应用以及高强度钢板使用中存在的主要问题及其对策等。     

含Zr低合金高强度钢中夹杂物的特性

用电子探针研究了含Zr低合金高强度钢中夹杂物的形貌、大小及分布等特性。结果表明 ,钢样中的夹杂物为圆形 ,呈分散分布 ,其组成系含ZrO2 的复合夹杂物 ,而且MnS依附此复合夹杂物成核和长大。钢中添加少量Zr可明显改善夹杂物形态和分布 ,从而改善钢的强度和韧性