Development of temperature compensated high elongation resistance strain gauges for use up to 250°C

The paper describes the development and evaluation of temperature compensated high elongation resistance strain gauges for use from room temperature to 250°C. These gauges could be temperature-compensated on steels with coefficient of thermal expansion α = 11 ppm/°C. Thermal output within 250°C was about 1 μm/m/°C and maximum standard deviation of 5 gauges was 34 μm/m. Strain limit was > 4% at room temperature and at 250°C. Gauge factors of different strain ranges at R.T. and at 250°C are tabulated. Some applications are stated.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

强流质子直线加速器中束晕现象研究

从束流包络方程与单粒子运动方程联立模型出发，考虑了纵向能量方程的耦合，研究了强流质子直线加速器中的束晕现象。采用相交间的Ｐｏｉｎｃａｒｅ截面方法和实空间Ｐｏｉｎｃａｒｅ截面方法，研究了周期聚焦系统失配的情况下束晕的形成以及加速对束晕形成的影响。     

HDPE的耐磨蚀性与抗冲击性的研究

用自制的旋臂式磨蚀实验仪，研究了５种高密度聚乙烯和１种顺丁橡胶改性的高密度聚乙烯，在铁尾矿和铁精矿浆体中的耐磨蚀性。耐磨蚀性最差的是ＨＤＰＥ２２００Ｊ，耐磨蚀性较差的是ＨＤＰＥ６３００Ｍ；ＨＤＰＥ５０００ｓ，６０９８和２４８０的耐磨蚀性较好；ＨＤＰＥ／ｃｉｓ－ＢＲ的耐磨蚀性最好。     

A Study of Surface Deformation during Wire‐Rod Rolling of High Speed Steels using Experimental and Computational Techniques

The evolution of surface defects during shape rolling of high‐speed steel billets is studied using longitudinal surface defects prepared by machining and welding. The reduction of the defects during rolling in a production mill is compared to the total area reduction of the billets. Samples are collected after pass 4, 6, 8, 14, 19 and the final pass, 28, representing the finished 5.5mm wire. By inspecting the cross sections, the rotation of the billets from pass to pass is evaluated. Results from FE simulations on solid billets are compared to the experimental results. Generally, simulations predict less reduction than observed experimentally. In most cases cracks reduce most effectively followed by carbon steel welds and stainless steel welds.     

不同品位高钛渣对沸腾氯化工艺的影响

分别以94％品位高钛渣和90％品位高钛渣为原料，采用沸腾氯化工艺制备粗TiCl4，分析了两种品位高钛渣对沸腾氯化工艺的影响。结果表明：94％品位高钛渣由于其活性低而对沸腾氯化工艺的影响较大。     

Inverse Analysis of Axisymmetrical Compression of HSLA Steel

The objective of the present work is to further explore the problem of selection of the flow stress function which will give the best agreement with experiments for a wide range of the Zener‐Hollomon parameter. Analysis of various flow stress functions was performed, with particular emphasis on the Zerilli‐Armstrong model. Inverse analysis was successfully applied to identify the flow stress model for microalloyed steels deformed in ferrite, two‐phase and austenite regions. Inverse method is applied to interpret the results of the axisymmetrical compression tests performed for HSLA steel samples on a Gleeble 3800 and Split Hopkinson Pressure Bar. Sensitivity analysis is performed based on local and global methods. The objective of the sensitivity analysis in the present study is the evaluation to what extent the selected coefficients in the rheological model influence the result of simulations. In the considered tests this result is represented by two dependent variables, the load and the shape of the sample (barrelling). It is confirmed that the Zerilli‐Armstrong equations should be applied at very high strain rates. Physical meaning is an advantage of this model. Difficulties with identification are the main disadvantage.     

浅议轨道交通直流牵引供电系统的构成及保护配置

介绍了城市轨道交通直流牵引供电系统的构成,详细叙述了直流牵引供电系统的主要电气设备及其连接方法,以及系统的运行方式.另外,还简单介绍了系统配置的直流保护以及保护原理和保护作用.     

摩擦诱发高铬铸铁相变的透射电镜研究

利用透射电子显微镜研究了高铬铸铁在摩擦过程中的显微组织变化。结果表明：奥氏体基体在摩擦应力的作用下发生相变。摩擦表面形成α‘Ｍ。次表层形成γ与α’Ｍ共存区；γ与．ε共存区；γ位错丛聚区。     

利用热管纺丝技术一步法生产FCY

利用平板型热管纺丝装置对普通高速纺丝机进行技术改造，并一步法生产出充分结晶的ＰＥＴ纤维（ＦＣＹ）。该纤维可直接用于织造，调节热管温度、热管安装位置可获得满足后道工序不同需要的ＦＣＹ。