新取代苯基荧光酮试剂的合成及其性质的研究Ⅱ．新型取代苯基荧光酮与金属离子显色反应的研究

研究了３，５－二溴－４－氨基苯基荧光酮、３，５－二溴－４－偶氮变色酸等８种苯基荧光酮在酸性介质中与高价金属离子Ｚｒ（Ⅳ）、Ｍｏ（Ⅵ）、Ｗ（Ⅵ）、Ａｌ（Ⅲ）、Ｇａ（Ⅲ）等的显色反应。３，５－位二溴取代的试剂的灵敏度高于未取代的灵敏度，摩尔吸光系数绝大多数在１０５Ｌ·ｍｏｌ－１·ｃｍ－１以上。     

高发泡聚乙烯阻燃初探

根据聚合物燃烧现象和一般阻燃机理寻求研究高发泡聚乙烯的阻燃方法和阻燃剂。研究结果表明:只有对添加型阻燃剂三元并用,方能不降低高发泡聚乙烯的物性,制得较为理想的高发泡聚乙烯自熄型制品。     

用于高压电容器的SrTiO3基陶瓷

报道ＳｒＴｉＯ３基陶瓷的制备方法和介电性质，给出了用此种陶瓷制成的高压电容器的试验结果，并对它位进行了讨论。     

A feasibility study of a direct-mapping parallel processing method to solve linear equations in load-flow calculation

With the growing size and complexity of power systems, system analysis—such as transients calculation—takes much time. Hence, fast calculation methods are required. Although parallel processing is a hopeful method, there have been difficulties in the parallel solution of linear equations which appear in power-flow calculations by the Newton-Raphson method. This paper aims at the fast calculation of the power-flow problem by means of parallel processing. In order to improve the suitability to the parallel solution of the differential equation in transients calculation, we assume the use of a direct-mapping parallel processing machine to map directly the network of a power system onto a network of processors. Under this assumption, we propose a new parallel-processing-oriented method in which the linear equation is solved by linear iterations between nodes with Aitken acceleration. We simulate the method on three model power systems and compare this Parallel Iterative Method (PIN) with a Parallel Direct Method (PDM) which uses the banded matrix according to the number of operations required. As a result, we can expect that PIM may solve linear equations faster than PDM with m processors, although the PIM might be inferior to the PDM with m × m processors, where m denotes the half-band width of the banded matrix.     

Li2O在保护渣中的作用

采用在不同玻璃性的两种基渣中加入Ｌｉ２Ｏ为研究Ｌｉ２Ｏ对保护渣粘度，熔化温度及玻璃性能的影响，并对Ｌｉ２Ｏ改善保护渣玻璃性的机理进行了探讨，提出了寻找高速连铸保护渣中Ｌｉ２Ｏ的代用物的一种方法。     

Measurement and prediction of pressure drop in two-phase flow

Experimental data for air–water two-phase co-current flow in two different pipe diameters were used to test the prediction of pressure drop by a number of existing theories and correlations. Several models are shown to be useful for prediction, particularly with the stratified regimes which have proved difficult to handle in the past. The model suggested by Olujic proved to be of particular value.     

彩色PDP用玻璃基板

本文讨论了彩色ＰＤＰ现用钠钙玻璃的热稳定性，指出由于这种玻璃在热处理过程中易变形和收缩，因而不适合作大面积彩色ＰＤＰ基板材料，介绍了彩色ＰＤＰ基板玻璃的制造方法和特点。最后介绍了日本旭硝子公司和美国康宁公司各自为彩色ＰＤＰ新开发的玻璃基板材料ＰＤ２００和ＣＳ２５。     

用小尺寸R－CT试样研究核压力容器钢断裂韧性及与Charpy试样的比较

提出了一种用双边带深侧槽的小尺寸圆形紧凑拉伸试样评定核压力容器（ＲＰＶ）钢断裂韧性的单试作试验方法，给出了用该方法测定的两个厂家生产的核压力容器用Ａ５０８ＣＬ３钢的断裂韧性参数，还与Ｃｈａｒｐｙ试样的试验结果及大尺寸标准试样的试验结果进行了比较。研究结果表明：用双边带深侧槽的小尺寸Ｒ－ＣＴ试样测得的断裂韧性值比相同恻槽深度预制疲劳裂纹Ｃｈａｒｐｙ试样的测试值更接近有效断裂韧性值，所以，用于核压力容器断裂韧性的监测是可行的。     

Ti,N,Mg对M2高速钢凝固组织和硬度的影响

为了改善Ｍ２高速钢共晶碳化物的分布，本文利用小凝固试样变质的方法研究了Ｔｉ，Ｎ和Ｍｇ对Ｍ２高速钢凝固组织和硬度的影响。试验结果表明，加入Ｔｉ或Ｔｉ－Ｎ后，共晶碳化物形态和分布有很大改善，而加入Ｔｉ－Ｎ后对凝固组织有轻微的细化作用，但只添加Ｔｉ不补碳时，钢的淬火硬度和回火硬度均下降；加入适量的Ｍｇ可以使片状的Ｍ２Ｃ型共晶碳化物转为鱼骨状的Ｍ６Ｃ型共晶碳化物，使其分布有所改善，Ｔｉ和Ｍｇ复合加入可以明     

高效防气防砂一体化管柱的研制与应用

为解决文南油田高气液比井出砂易造成卡泵的问题,研制了高效防气防砂一体化管柱。该管柱主要由闭式气锚、重力式防气装置和激光割缝筛管3部分组成。闭式气锚的分离作用消除了气体对抽油泵的影响,提高了泵效;重力防气装置利用液气分离原理和高烟囱原理进行液气分离,液流回流时间可达10min,排气最高压差可达0.2MPa;经激光割缝筛管过滤后的液体含砂粒外径小于0.05mm。该管柱在文南油田现场应用16井次,累计增液6000t,增油2717t,平均单井泵效提高7%。