交流变频调速技术在二辊轧机压下系统中的应用

介绍一种采用变频调速技术控制的二辊轧机压下系统。该系统可控制轧机压下系统的速度在工艺要求的范围内无级可调，压下量以数字动态显示，控制准确、操作方便。文中对系统的组成及工作原理作了较详细的介绍。     

多缝式烧嘴点火器在攀钢烧结生产中的应用

多缝式烧嘴点火器具有燃烧效率高，火焰长度易调，炉膛温度分布合理等优点，经工业试验证明，该点火器能满足攀钢烧结点火工艺要求，并有明显节能效果。     

通过直接栅电流测量研究PMOSFET's热载流子损伤

通过直接栅电流测量方法研究了热载流子退化和高栅压退火过程中PMOSFET's热载流子损伤的生长规律.由此,给出了热载流子引起PMOSFET's器件参数退化的准确物理解释.并证明了直接栅电流测量是一种很好的研究器件损伤生长和器件参数退化的实验方法.     

Processing and properties of zirconia-toughened alumina ceramics

Al₂O₃:ZrO₂ ceramics have been prepared from physically mixed pure oxide powders. The results indicate that careful processing of the starting powders and a two-stage sintering process can avoid expensive processing methods like hot pressing/hot isostatic pressing used for achieving high densification. The mechanical properties were measured and the resultant microstructure studied to explain the toughening behaviour of this material.     

粉末布法制备SiC/Ti基复合材料

用粉末布法制备了低成本SiC/Ti基复合材料.结果表明,采用合适的轧制参数即可容易地获得厚度合适、均匀的粉末布;热失重分析和热解残余物分析指出用来制备粉末布的有机粘结剂的去除过程分成两个阶段,合理除气后,基本没有残余物.使用真空热压工艺制备的SiC/Ti基复合材料,纤维分布基本均匀,纤维与基体的界面结合良好.     

Effect of water inlet velocity on thermal stratification in a mantled hot water storage tank

Thermal stratification in a mantled hot water storage tank is analysed numerically for different water inlet velocities. The aim is to obtain higher thermal stratification and supply hot water for usage as long as possible. Twelve different water inlet velocities to the hot water storage tank are considered. The numerical method is validated by comparing its results against experimental and numerical results from the literature. It turned out that the results obtained from the numerical analysis have shown very good agreements with the results from previous works. As a result, the water temperature in the tank increases with the increase of the water inlet velocities to the mantle but this increment is not proportional. After a period of operation of 7.2 h, which corresponds to the average sunshine duration in Turkey, temperature increments of 6.5 and 35 K have been estimated for the hot water inlet velocities of 0.01 and 0.3 m s^?1, respectively, at a radial distance of 0.1 m and a height of 1 m inside the storage tank. Copyright © 2005 John Wiley & Sons, Ltd.     

液态中锰渣摇包生产高硅锰硅合金的探讨

论述了利用液态中锰渣摇包生产高硅锰硅的原理、工艺过程热平衡,并介绍了其操作过程、主要影响因素及所取得的经济、社会效益.     

水冷热模法离心铸造大口径球铁管用管模涂料

阐述水冷热模法管模涂料的组成。说明了耐火基料，悬浮剂、粘结剂，减水剂的各自作用机理，提出了合理的涂料配方、合适的喷涂方式。     

优化锰铁高炉配矿结构

介绍了通过优化高炉锰铁烧结矿原料结构，改善了烧结矿性能，使锰铁冶炼取得了增产、节焦、降成本的明显效果。     

添加CaF2-YF3的AlN陶瓷的热导率

用CaF2和YF3做添加剂，在1750℃制备了热导率高于170W/m.K的的AlN陶瓷，并用XRD和SEM研究了AlN陶瓷在烧结过程中的相组成，微结构以及晶格参数的变化，并讨论了其对热导率的影响，研究发现，当使用CaF2-YF3做添加剂时，微结构差异对AlN陶瓷热导率的影响很小，AlN陶瓷的热导率主要由AlN晶格氧缺陷浓度决定，由于CaF2-YF3能有效降低AlN颗粒表面的氧含量，从而有利于获得高的热导率。