籼米淀粉超微粉体的制备及其性质

研究了籼米淀粉超微粉体的一种新的制备方法 ,通过正交实验确定了酶处理淀粉的最佳条件 ,考察了淀粉的溶解度和膨润力。结果表明 ,酶处理淀粉的最佳工艺参数为 :水解温度４５℃ ,时间为２５ｈ ,酶用量为水解淀粉的４５%。随着粒径的减小 ,淀粉的溶解度增大 ,膨润力下降。     

化学还原法制备纳米铜粉的研究

本文采用KBH4在液相中化学还原CuSO4,并加入KOH和络合剂EDTA ,制得了纳米级的纯净的铜粉 ,通过调整反应物的浓度 ,可以消除Cu2 O等杂质。制备的纳米铜粉还存在一定程度的团聚 ,需试验加入分散剂来改善。     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。     

超细粉碎技术现状及发展趋势

综述了国内外超细粉碎技术及设备的现状、进展,指出了其发展趋势,从工作原理、结构特点等方面详细介绍了超细粉碎典型设备,同时又指出了近年来国内外在此领域中的新进展,基于现存问题指出了今后超细粉碎研究的方向。     

高性能各向异性Sm2Fe17Nx磁粉的制备

本文研究了高性能各向异性Ｓｍ２Ｆｅ１７Ｎｘ磁粉的制备工艺路线与工艺参数。优化了制备与工艺参数。已制备出磁性能达到：Ｂｒ＝１．３９Ｔ，Ｈｃｉ＝８５０ＫＡ／ｍ和（ＢＨ）ｍ＝２３６ＫＪ／ｍ＾３的各向异性Ｓｍ２Ｆｅ１７Ｎ２．８８磁粉，该磁粉的各向异性场ＨＡ达到２０Ｔ。     

Preparation and Properties of Sintering Additives Coated Si3N4 from Heterogeneous Nucleation Processing

The sintering additives such as Al2O3 and /or Y2O3 were coated on the surfaces of Si3N4 particles via heterogeneous nucleation processing using a buffered pH solution as the precipitation reagent .They nucleated and grew only on the surfaces of Si3N4 and did not form sol particles in solution by TEM observation .The isoelectric point(IEP) of coated Si3N4 was different from that of as-received Si3N4.The IEP of Al(OH)3-coated Si3N4 occurred at pH8.4, which is close to that of alumina .When Al(OH)3-coated Si3N4 particles were coated with Y(OH)3,the IEP of coated Si3N4 powder shifted from pH8.4 to pH9.2 ,similar to that of yttria.In addition ,the rheological data showed that Al2O3 and /or Y2O3 coated Si3N4 suspension is nearly Newtonian and that added Si3N4 suspension shows a shear rate thinning behavior.     

Li2O在保护渣中的作用

采用在不同玻璃性的两种基渣中加入Ｌｉ２Ｏ为研究Ｌｉ２Ｏ对保护渣粘度，熔化温度及玻璃性能的影响，并对Ｌｉ２Ｏ改善保护渣玻璃性的机理进行了探讨，提出了寻找高速连铸保护渣中Ｌｉ２Ｏ的代用物的一种方法。     

XH－Ⅰ型岩石铵梯炸药研究

文章论述利用过期火药的一种新途径。在２号岩石铵梯炸药中加入粉碎的过期火药以代替部分梯恩梯，制成一种ＸＨ－Ⅰ型岩石铵梯炸药，适用于各种爆破工程。并具有较高的经济效益和社会效益。     

Final Drying of Whole Milk Powder in Vibrated-Fluidized Beds

Vibro-fluidized beds are widely used in drying sticky powders and agglomerated materials as milk powder. Using a vibro-fluidized laboratory scale dryer, this work is aiming at analyzing preliminarily the effect of its operational variables on the drying kinetics and characteristics of whole milk powder. The full-factorial design technique with three replications at the central point has been employed to generate data and correlations to quantify the effect of inlet air temperature, air flow rate, and vibration bed amplitude on the drying curves and the milk powder properties related to its faster reconstitution in water (as tapped density, Hausner cohesion ratio, agglomerate size distribution, and internal pore concentration). Results obtained are analyzed and discussed to identify the adequate operation condition for final drying whole milk powder in vibro-fluidized beds, assuring a high product quality.