湿H2S环境中金属材料腐蚀的研究

介绍了在湿H2S环境中金属材料的腐蚀试验标准、方法和手段并重点强调了在H2S试验过程中常遇到的一些问题的处理方法.最后,指出了应加强H2S腐蚀的基础性和系统性研究的研究方向.     

锌钾硼对甜菜产质量效应及最佳施肥措施的研究

本文利用最优回归设计“310”方案,研究了黑土地甜菜 Zn、K_2O、B的效果及合理施用问题。得出甜菜块根产量、含糖、产糖量、灰分 K 和有害 N 与 ZnK_2O、B 肥回归关系显著的回归模型,分析了 Zn、K_2O、B 对上述五个指标的效应,明确了 Zn 是影响各项指标的主要因子,并采用频率筛选法,提出了兼顾上述五项指标的优质高产施肥措施。     

部件试验模态综合的简便方法

本文将一种基于完备模态基的模态综合技术应用于子结构的试验模态综合,获得成功。这种半试验半理论的模态综合方法是一种较为简便的、要求试验工作量较小的试验模态综合法,因为它只要求测量子结构的振动模态和频率即可。数值仿真结果表明,这种简便的试验模态综合法是行之有效的。     

On the mechanical behavior of aluminum alloys reinforced by long or short alumina fibers or SiC whiskers

This study was initiated to examine the dispersion of longitudinal and transverse waves in metal matrix composites in order to obtain the dynamic elastic modulus and to evaluate various models for predicting the composite's macroscopic elastic constants from the properties of its constituents. The materials chosen for this investigation were alumina continuous fibers on the one hand and alumina and SiC short fibers on the other hand, all embedded in an aluminum alloy matrix. In addition, some indications have been obtained experimentally for the acoustoelastic effect in the composite.     

微波等离子体化学气相沉积的 a-Si∶H 性能研究

本文着重对微波等离子体化学气相沉积法高速沉积的 a-Si∶H 膜的物理性能进行评价研究.测量了沉积膜的光电性能、暗电导激活能、光禁带宽度、光吸收特性、沉积膜中悬键态密度以及氢含量等,并讨论沉积条件对膜性能的影响.结果表明,在沉积速率高达30～90(?)/s 情况下,膜的光电导(光照强度10~5Lux)与暗电导比值可达10~3～10~5,暗电导率从10~(-3)到10~(-11)((?)cm)~(-1),其激活能在0.23～0.88eV 之间(0～200℃温度范围内),光禁带宽度为1.40～2.20eV,氢含量约为2～20%.     

SIMATIC S5—115U可编程控制器

本文通过对SIMATIC S5—115U可编程控制器性能的简介,简述国外PC技术的现状和发展,并提出对PC国产化的看法.     

The fracture stress of chemical vapour deposited diamond

The factors which control the fracture stress of chemical vapour deposited diamond have been studied using the 3-point bend geometry. Fracture stress values of 300–800 MPa for the growth side and 600–1200 MPa for the nucleation side were recorded for samples of thickness 0.4–2.4 mm. A Weibull modulus of 23 was calculated for the growth surface data, showing that the fracture stress variability was low for a brittle material. A theory based on these results demonstrates that the material behaviour is remarkably simple, depending only on the grain size and the sample thickness, regardless of wide variations in other parameters such as optical transmission and stress state. The paper also contains a possible explanation for this well-defined behaviour based on microstress variations resulting from differences in defect density in different growth sectors within a grain.     

Cationic ring-opening polymerization of hexamethylcyclodisilazane: General aspects and tentative mechanisms

The ring-opening polymerization of hexamethylcyclodisilazane (D_2NMe), initiated by methyl triflate in 1,2-dichloroethane, forms in the first, fast kinetic step both linear polymer and cyclic dimer (D_4NMe). Subsequently a slow depolymerization process occurs leading to exclusively cyclotrisilazane (D_3NMe). On the basis of kinetic measurements carried out using an adiabatic calorimetric technique and complementary experiments, mechanisms of both propagation, cyclization and back-biting reactions are proposed. The influence of the reaction temperature was also studied; it is demonstrated that, at low temperature, polymerization does not lead to cyclic oligomer formation. In such conditions, the polymerization presents a ‘living’ character.     

Possible tactics to improve the growth of single-walled carbon nanotubes by chemical vapor deposition

The growth time, growth mode and the method of preparing the supported catalysts play an important role in the growth of single-walled nanotubes (SWNTs). Their effects on the chemical vapor deposition (CVD) growth of SWNTs with MgO-supported catalysts were investigated in this study. It is shown that the growth rate of SWNTs was large during the initial few minutes of growth, however the quality of the tubes was low owing to the formation of many defects. Long term growth may favor the formation of tubes with high quality and high yield, but the introduction of other forms of carbon (impurities) is also unavoidable. There was a balance between the increase in yield and quality and sacrifice of the purity during growth of SWNTs. MgO-supported catalysts prepared by the co-precipitation method were found to be more effective for the synthesis of SWNTs than those prepared by the widely used impregnation method. The size and dispersion state of the catalyst were found to be crucial in enhancing the growth of SWNTs. In addition, growth on the surface of SWNTs over nanosized catalyst films was shown to be more favorable for the synthesis of tube products with higher quality, yield and purity.     

光纤码分多址技术在城域接入网中的应用

分析了光纤码分多址技术O -CDMA在城域接入网中的应用。回顾了O -CDMA技术的发展历史 ,详细地介绍了O -CDMA技术的特点 ,其具有的公平性、灵活性、网络控制管理、对服务区处理能力以及高的安全性使O -CDMA技术成为较好的城域接入网技术。阐述了目前在应用中O -CDMA存在的一些技术方面的问题