六铝酸钙材料的合成及其显微结构研究

分别采用轻质碳酸钙和活性氧化铝 ,或纯铝酸钙水泥和活性氧化铝为初始原料 ,反应烧结合成了六铝酸钙 (CA6)材料 ,研究了原料和成型压力对合成材料的烧结性能和显微结构的影响 ,同时借助于XRD、TG -DSC、SEM和EDAX等测试手段对其反应过程、物相变化和显微结构进行了分析和观察。研究结果表明 :(1) 130 0℃时 ,合成材料的主晶相为刚玉相和CA2 ,并开始有CA6形成 ;温度升至14 0 0℃ ,CA6大量生成 ;15 0 0℃时反应完成 ,产物全部为CA6相。 130 0～ 15 0 0℃时 ,上述反应表现为体积膨胀过程 ,试样的体积密度和径向线收缩率随温度的变化不大 ;而高于 15 0 0℃时 ,试样明显趋向烧结 ,体积密度升高 ,线收缩率加大。采用纯铝酸钙水泥和活性氧化铝合成的试样的体积密度均高于采用轻质CaCO3 和活性氧化铝的 ,尤其在烧成温度高于 15 0 0℃时。坯体的成型压力对这两种合成试样的烧结性能均没有显著影响。 (2 )合成六铝酸钙材料的晶粒形貌与合成工艺有关 ,制备片状晶粒的六铝酸钙材料需满足两个条件 :一是晶核有足够的发育空间 ,二是从晶核生长形成片状结构需足够的物质扩散。采用纯铝酸钙水泥和活性氧化铝为原料的试样 ,其CA6晶核很容易发育成片状晶形 ,且随着坯体成型压力的增加 ,片状CA6有向等轴状发展的趋势 ;采用     

Degree of crosslinking and mechanical properties of crosslinked poly(vinyl alcohol) beads for use in solid-phase organic synthesis

The limited swellability in polar media of the commonly used polystyrene/divinylbenzene (PS-DVB) support materials for solid-phase organic synthesis has led to the development of novel, highly swellable hydrophilic gels designed for use in aqueous or polar media. Poly(vinyl alcohol) beads crosslinked with epichlorohydrin (PVA-EP) were prepared by a two-step inverse-suspension polymerization method. While it is known that the morphology of the resulting beads can be controlled by the ratio of EP versus PVA as well as by the pre-crosslinking time, the actual degree of crosslinking of the beads and their mechanical properties remain unknown. It is therefore the purpose of this study to evaluate the actual degree of crosslinking of beads prepared with different quantities of crosslinker in the feed by spectroscopic (Raman, nuclear magnetic resonance) and chemical (functional group loading) methods. The mechanical properties of these swollen PVA-EP beads will be evaluated by single-bead unconfined compression in solvents such as water, N,N-dimethylformamide (DMF), and tetrahydrofuran (THF) and compared to model PS-DVB beads commonly used for solid phase synthesis.     

微粉对矾土基超低水泥浇注料性能的影响

以高铝矾土熟料为主原料 ,加入 2 %的铝酸钙水泥及总量为 6 %的Al2 O3 微粉和SiO2 微粉 ,配制了矾土基超低水泥浇注料 ,研究了微粉对浇注料的烧结性能、力学性能及热震稳定性的影响。结果表明 :(1 )SiO2 微粉对浇注料的促烧结作用优于Al2 O3 微粉。这是因为与Al2 O3 微粉相比 ,由气相沉积生成的SiO2微粉的粒度小 ,比表面积大 ,活性较高。 (2 )随着SiO2微粉加入量的增加 ,在 1 1 0 0℃和 1 4 0 0℃处理后的常温强度以及在 1 30 0℃和 1 4 0 0℃下的高温抗折强度和抗热震性明显提高。这是由于引入的SiO2 微粉在高温下与Al2 O3 反应生成的针状莫来石穿插进入刚玉骨架 ,起着明显的强化和韧化作用     

Antimicrobial protection of cotton and cotton/polyester fabrics by radiation and thermal treatments. I. Effect of ZnO formulation on the mechanical and dyeing properties

Cotton and cotton/polyester fabrics were treated against microbial attack by applying a formulation based essentially on ZnO under high‐energy radiation and thermal curing. To achieve the homogeneity and the reactivity of the treating formulation, a binder (Impron MTP) and a dispersing agent (Setamol WS) were used with ZnO. The antimicrobial property of the fabrics was evaluated, in terms of mechanical properties, by a soil burial test. Moreover, the effect of antimicrobial finishing on the dyeing properties in terms of color strength was investigated. It was found that the best composition that affords the best antimicrobial protection to cotton fabrics contains 2% ZnO, 2% binder, and 1% dispersing agents. For the cotton/polyester blend, the best results were achieved at the same conditions except the ZnO was 1%. It was found that the treatment under the effect of electron‐beam irradiation is better than that of gamma irradiation and thermal curing. The results showed that when the finishing process was carried out before dyeing with a reactive dye, it affects the color strength rather than performing the finishing after the dyeing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1129–1137, 2003     

PVA-based activated carbon fibers with lotus root-like axially porous structure

A novel method was developed for the fabrication of activated carbon fiber (ACF) with wet spinning polyvinyl alcohol (PVA) fibers as the precursors. Through a combination of preoxidation, dehydration, carbonization and activation under a certain tension, PVA-based ACFs (PVA-ACFs) with high yields and good mechanical properties were obtained. The surface and cross-section morphologies, pore structures, surface geometries, surface functional groups and crystal structures of the PVA-ACFs were characterized using field emission scanning electron microscopy, low temperature nitrogen adsorption, Fourier transformed infrared spectrophotometry, X-ray photoelectron spectroscopy and X-ray power diffraction. All the PVA-ACF samples prepared had lotus root-like axially meso- and macroporous structures with the domination of micropores. Fractal geometries of PVA-ACFs deduced from nitrogen adsorption isotherms indicates that capillary force dominated in the interactions between nitrogen and the PVA-ACFs. The surface functional groups of the PVA-ACFs depend on the activating agents. Graphitoidal crystal structures were observed for the PVA-ACFs. The small crystal size and short range ordering between the crystallites ensured a high specific surface area of the PVA-ACFs.     

Carbonaceous adsorbents from sewage sludge and their application in a combined activated sludge-powdered activated carbon (AS-PAC) treatment

In this study, waste biological sludge is converted to an adsorbent by chemical activation with sulphuric acid. The adsorbent obtained is then applied to the aerated vessel of an activated sludge process treating glucose and phenol to improve the quality of the treated effluent. The sludge-based carbonaceous adsorbent was found to be mesoporous in nature, with a good adsorption capacity for large molecular weight compounds and limited removal efficiency for smaller molecules such as phenol. The addition of carbon, either sludge-based or commercial, enhanced phenol removal from 58% to 98.7% and from 87% to 93% the organic matter removal as measured by the chemical oxygen demand (COD) when operated with feed concentrations of 100 mg phenol/l and 2500 mg COD/l. No differences were found between the activated sludge-activated carbon bench scale continuous reactors operating with either commercial or sludge-based adsorbents in spite of the higher adsorption capacity of the former. It is suggested that powdered adsorbent bioregeneration in the combined AS-PAC system may be impaired by the obstruction of pores due to bacterial growth, the effect being more important for the commercial activated carbon with a narrower pore size distribution.     

Induction plasma synthesis of fullerenes and nanotubes using carbon black–nickel particles

The existence of fullerenes (as allotropes of carbon) was established in the mid-1980s and during the last 15–18 years, systematic efforts have been devoted to improve the methods of their synthesis, including plasma-based system methods. The work presented here is focused on the investigation of fullerenes synthesis, using a radio frequency plasma reactor. The main objectives were to explore the use of induction plasma technology for the synthesis in-continuo of carbon fullerenes and to predict their formation conditions through conduct of theoretical studies. Thus, a thermodynamic study was carried out to predict the equilibrium composition of fullerenes produced at several combinations of operating conditions. Additionally, a statistical factorial design experiment, employing four factors at two levels, was also developed, in order to study the influence of the system’s operating parameters on the eventual C₆₀ fullerene yield. The results obtained showed that the reactor pressure, the electrical power and the raw material feed rates all have an important effect on the synthesis of fullerenes. The highest C₆₀ concentration in the products was found to be about 7.7 wt.%. Various other carbon nanostructures, such as nanotubes and nano-onions, were also successfully produced.     

On the preparation and properties of CuZSM-5 catalysts for NO decomposition

Equilibrium exchange isotherms were determined for the exchange of Cu²⁺ with NaZSM-5 at varying Cu(Ac)₂ concentrations in solutions of constant volume and zeolite weight. At low Cu²⁺ levels the solid scavenged all the copper ions. When copper could be detected in the equilibrated solutions, overexchange was observed. The extent of overexchange was higher at pH 6 than at pH 4. These results were analyzed in relation to catalytic activity.On leave from the Central Institute for Chemistry, Hungarian Academy of Sciences, H1525 Budapest, Hungary.     

dc Electrical Degradation of Perovskite-Type Titanates: I, Ceramics

The rate of the resistance degradation of doped SrTiO₃ ceramics is investigated as a function of various external and material parameters. The effects of the mutually interrelated parameters dc voltage, dc electric field, and thickness of the dielectric are described by power laws. Electron microscopic potential contrast studies show a Maxwell-Wagner polarization leading to a concentration of the electric field at the grain boundaries during the degradation. Based on this finding, the voltage step per grain boundary, ΔΘ_gb, is introduced as a rate-determining parameter which allows an explanation of the influence of the grain size on the degradation rate as well as the difference in the power laws for ceramic and single-crystal samples.     

熔融石英耐火材料

阐述了熔融石英耐火材料的主要性能与应用领域。