红外光谱法用于快速测定车用柴油酸度等性质的研究

针对车用柴油酸度等性质测定过程繁琐，采用衰减全反射样品池测定车用柴油的红外光谱，用偏最小二乘法（PLS）建立红外光谱测定车用柴油酸度、密度、闪点和凝点的4个校正模型，验证标准误差分别为0.46 mg/(100 mL),0.77kg/m3,2.60 ℃,2.77 ℃，该方法符合标准方法再现性要求。与标准方法相比，该方法具有无需预处理、操作简单、测量快速、重复性好等优点。     

心电地图仪中工频干扰的一种滤除方法

在心电地图仪中记录到的体表心电信号往往由于电磁的影响而引进工频干扰．基于体表心电信号中工频干扰的特点，作者提出了一种滤除工频干扰的方法，即就单独—胸导联信号通过提高频谱的分辨率来估计工频干扰的频率；基于最小均方误差准则来估计各导联信号中工频干扰的幅度和相位。文中还给出了该算法的流程图和滤波性能分析。模拟结果表明了该算法的有效性。应用该算法对心电地图仪中的工频干扰进行对消，取得了满意的结果。     

局部设有钢筋砼电梯井墙的设计探讨

本文就局部设有钢筋砼电梯井的工程计算及理论分析，阐明分析了少墙的框剪结构的设计及注意问题。     

Comparison of inward and outward grown Pt modified aluminide diffusion coatings on a Ni based single crystal superalloy

Two commercial Pt modified aluminide coatings (RT22 and MDC150L) on the same single crystal Ni-based superalloy (CMSX-4) were studied by: scanning electron microscopy; transmission electron microscopy; energy dispersive X-ray spectrometry; and gravimetry. The RT22 coating is an inward grown coating (high activity), while MDC150L is produced by outward growth (low activity). Samples were oxidised in still laboratory air at 1050 °C for various times up to 2000 h. It was found that the outward grown coating produced a slower growing oxide that was more spallation resistant. Several possible reasons for this were identified including: coating purity; coating surface topography; and ductile to brittle transition temperature. The microstructural differences between the two coatings in the as-coated condition were investigated and the development of their microstructure during heat treatment was described. A model for coating growth during heat treatment was proposed.     

ASYMPTOTIC PROPERTIES OF THE SAMPLE AUTOCORRELATIONS AND PARTIAL AUTOCORRELATIONS OF A MULTIPLICATIVE ARIMA PROCESS

Abstract. We shall investigate the asymptotic behaviour of the sample autocorrelations and partial autocorrelations of a multiplicative ARIMA process and derive their limiting distributions. Some simulations are presented to illustrate the results obtained.     

Discrete singular convolution and its application to the analysis of plates with internal supports. Part 2: Applications

Part 2 of this series of two papers presents the applications of the discrete singular convolution (DSC) algorithm. The main purpose of this paper is to explore the utility, test the accuracy and examine the convergence of the proposed approach for the vibration analysis of rectangular plates with internal supports. Both partial internal line supports and complex internal supports are considered for 21 square plates of various combinations of edge support conditions. The effects of different size, shape and topology of the internal supports and different boundary conditions on the vibration response of plates are investigated. The partial internal line supports may vary from a central point support to a full range of cross or diagonal line supports. Several closed‐loop supports, such as ring, square and rhombus, and their combinations are studied for complex internal supports. Convergence and comparison studies are carried out to establish the correctness and accuracy of the DSC algorithm. The DSC results are compared with those in the available literature obtained by using other methods. Numerical results indicate that the DSC algorithm exhibits controllable accuracy for plate analysis and shows excellent flexibility in handling complex geometries, boundary conditions and support conditions. Copyright © 2002 John Wiley & Sons, Ltd.     

Simultaneous Spectrophotometric Determination of Three Components Including Deoxyschizandrin by Partial Least Squares Regression

1IntroductionWuweizi is a traditional Chinese herb,usually usedto cure cough,asthma,neurasthenic,hepatitisetc.Theactive ingredients in wuweizi are5%-22%lignan,themain components of which include deoxyschizandrin,schizandrin andγ-Schizandrin.Forthe purpos…     

Power sector development in India with CO2 emission targets: Effects of regional grid integration and the role of clean technologies

The power sector in India at present comprises of five separate regional electricity grids having practically no integrated operation in between them. This study analyses the utility planning, environmental and economical effects of integrated power sector development at the national level in which the regional electric grids are developed and operated as one integrated system. It also examines the effects of selected CO₂ emission reduction targets in the power sector and the role of renewable power generation technologies in India. The study shows that the integrated development and operation of the power system at the national level would reduce the total cost including fuel cost by 4912 million $, total capacity addition by 2784 MW, while the emission of CO₂, SO₂ and NO_x would be reduced by 231.6 (1.9%), 0.8 (0.9%), 0.4 (1.2%) million tons, respectively, during the planning horizon. Furthermore, the study shows that the expected unserved energy, one of the indices of generation system reliability, would decrease to 26 GWh under integrated national power system from 5158 GWh. As different levels of CO₂ emission reduction targets were imposed, there is a switching of generation from conventional coal plants to gas fired plants, clean coal technologies and nuclear based plants. As a result the capacity expansion cost has increased. It was found that wind power plant is most attractive and economical in the Indian perspective among the renewable options considered (Solar, wind and biomass). Copyright © 2003 John Wiley & Sons, Ltd.     

3D velocity from 3D Doppler radial velocity

We present local least squares and regularization frameworks for computing 3D velocity (3D optical flow) from 3D radial velocity measured by a Doppler radar. We demonstrate the performance of our algorithms quantitatively on synthetic radial velocity data and qualitatively on real radial velocity data, obtained from the Doppler radar at Kurnell Radar station, Botany Bay, New South Wales, Australia. Radial velocity can be used to predict the future positions of storms in sequences of Doppler radar datasets.© 2005 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 15, 189–198, 2005     

A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.