轻质油中C1—C7轻烃的地球化学特征

作者对5个盆地18个轻质油样品作了C_1—C_7轻烃分析,检测出29种单体轻烃。通过轻烃组成特征研究,认识到石蜡指数(PI_1)和庚烷值(PI_2)作为成熟度的指标,不受沉积盆地类型影响;C_6,C_7烃类族组分受母质类型影响较大。陆相(含煤地层)有机质生成轻质芳烃(苯)的含量比海相有机质要高。新疆塔里木盆地沙参2井原油的轻烃分析资料表明,该井油源岩为海相沉积。     

坨五站中间乳化层快速增长原因及治理方案

胜利采油厂坨五站高含水(95％)原油化学预脱水中，二级沉降罐内油水相之间的中间乳化层增长迅速，引起了一系列问题。现场调查和大量室内测试结果表明，产生这一现象的原因有：油溶性破乳剂WD-1加入点不合理。有2／3的含水原油在通过油水分离器之后才与破乳剂混合；二级沉降罐进油口伸入油相内，油流的冲击达不到中间层；WD-1对坨五站混合原油中的稠油破乳脱水性能欠佳，不能适应坨五站混合原油组成和含水的变化。针对上述各种原因筛选出了性能更好的一种破乳剂1916。根据确定的几种原因采取了相应的措施：将破乳剂加入点改在3个并联油水分离器之前；将二级沉降罐的进油口移到水相内；改用筛选出的破乳剂1916，结果使中间乳化层的增长受到了抑制。图2表4参2。     

酸化返出液中分离出的原油脱水时电脱水器跳闸原因及对策

海上油井酸化后,油井返排液沉降分离得到含酸原油,后者进入电脱水器后常引起电脱水器跳闸。其原因是含酸原油(油包水型乳状液)的电导率过高,超过了电脱水器的安全工作电导率κw。对于现场所用的电脱水器,由设计参数计算出κw=0.43μS/cm。从某海上油田3口油井酸化后不同时间的返排液共取样40份,随机选出13份,沉降分离后得到13份含酸原油样,测得电导率范围在0.03～10000μS/cm。认为原油的含水率(应<18%)不是引起跳闸的原因,跳闸的主因是含酸原油的高电导率。研制了一种油溶性的碱性添加剂,其化学成份是碱金属、碱土金属氧化物或氢氧化物,以浓溶液形式加入含酸原油中,可使电导率降至κw以下。加入量由实验确定。表2参2。     

Synthesis and characterization of antioxidants and detergent dispersant based on some polyisobutylene copolymers

Polyisobutylene succinic anhydride-urea/polyamines (PIBSA) copolymers were synthesized as potential antioxidants and detergent dispersant agents for lubricating oils samples (SAE-30). Homogeneity, thermal stability and dispersancy of the solutions were determined. Fully soluble oil compounds that are thermally stable up to 250 °C were achieved. The oxidation stability of lube oil samples in the presence of four designed PIBSA additives (varying in the number of amine groups) was determined for a time period of up to 72 hours. The dependence of the additive efficiency on its concentration was studied to achieve maximum stability. Some PIBSA additives at concentration 3.0 · 10⁴ ppm exhibit the best results. Dispersivity values were measured at predetermined oxidation times. The results proved reliable dispersion capability as the nitrogen content of the additive is increased, i.e. the increase in the basic character of the additive leads to the increase in the neutralization capability. Moreover, the designed PIBSA additives retain their efficiency after long oxidation times, confirming their role as multifunctional nitrogen containing polymeric additive. Electronic Publication     

膨胀石墨对各种油类的吸附动力学

通过对吸附率(有效吸附系数)Ks和饱和吸附量msat的测量,描述了粘度为0.001 Pa·s～0.850 Pa·s的各种油类在膨胀石墨柱中的吸附动力学,发现吸附率Ks对油类粘度有很强的相关性.吸入膨胀石墨柱中的饱和吸附量msat几乎恒定在50kg/kg,该值略低于由膨胀石墨块直接浸渍在油中测得的吸附容量,这是由于所吸附的油沿膨胀石墨柱高度存在重力梯度.     

Effects of irradiation in combination with waxing on the essential oils in orange peel

The study evaluated the effects of waxing, irradiation dose and post‐irradiation storage time on the essential oils in orange peel. Mature oranges (Maroc late) waxed or unwaxed were treated with 1 or 2 kGy radiation and stored for 9 weeks at 20 °C and 40–50% RH. Essential oils from the peel were extracted and analysed by GC. Results showed that D ‐limonene was significantly lower in waxed oranges; levels in samples treated with 2 kGy were higher than those in non‐irradiated or treated with 1 kGy. Linalool, methyl anthranilate and 3,7‐dimethyl‐2,6‐octadienal decreased as the dose increased. Levels of linalool increased with storage time but D ‐limonene was unaffected. These results may aid in guaranteeing the quality of orange essential oils during storage time. Copyright © 2004 Society of Chemical Industry     

长庆油田陕北区原油破乳剂的筛选和复配

实验考察了8种市售水溶性破乳荆对长庆油田陕北区有代表性的宝塔区、安塞和子长原油(均为低硫中间基-石蜡基原油)的脱水效果(加量100mg／L，脱水温度55℃，时间3h)。目前长庆采油一厂使用的YT-100和延炼集团使用的GT-940对这3种原油的脱水效果均较好，但对子长原油的脱水率不高，分别为69．7％和58．9％。在由所选性能较好的破乳刺组成的4种二元复配物中，GT-940 HQ96-1对3种原油的脱水效果均高于单剂，最佳配比分别为4：1，4：1，3：2；其余3种复配物则对原油有选择性，其中GT-940 YT-100相近(97．5％)；YT-100 HQ96-1仅能改善子长原油的脱水效果，配比为4：1时脱水率最高(76．4％)；SP-169 HQ96-1仅能改善宝塔区原油的脱水效果．配比3：2和2：3时脱水率最高(92．9％)。表5参6。     

成品油储罐内的腐蚀及防护

对成品油储罐内各部位腐蚀情况进行了介绍，说明了产生腐蚀的原因和腐蚀机理。介绍了油罐内防护技术，采用节点加固，降低边缘应力，可减缓油罐金属腐蚀速度；对选用油罐内防腐涂料的原则进行了阐述。     

巧用营销策略 开发零售市场

综述了在成品油市场竞争日趋激烈的形势下，做好成品油销售工作的经验和体会，介绍了领导带上，上下剂心协力，分析用户的需求和用油规律，抓住商机，以适合市场规律的营销策略和热情周到的服务，现固已有市场，并开拓了新市场的做法。     

Concepts,processing, and recent developments in encapsulating essential oils

By the virtue of their olfactory, physicochemical, and biological characteristics, essential oils (EOs) have drawn wide attention as additives in daily chemicals like perfume or personal care products. Nevertheless, they are physicochemically unstable and susceptible to degradation or loss. Microencapsulation offers a feasible strategy to stabilize and prolong release of EO. This review summarizes the recognized benefits and functional properties of various preparation and characterization methods, wherein innovative fabrication strategies and their formation mechanisms are especially emphasized. Progress in combining detecting/measuring technologies with kinetic modelling are discussed, to give an integral approach of controlling the dynamic release of encapsulated EOs. Moreover, new development trends of EOs capsules are also highlighted.