论高层建筑中央空调水系统水压试验的步骤

通过对中央空调水系统安装的特点分析,确定了应用效果良好的试压步骤。     

MCRC��ǻ��չ��ճ�̽

本文根据MCRC引进装置的情况,对加拿大Delta公司的MCRC硫回收工艺作了初步探索,介绍了该方法的工艺特征,并评述了引进装置的性能考核结果。文中还结合四川气田建厂的环保要求,评价了MCRC方法的使用价值及意义。     

一种新型声波降粘防蜡装置

新型声波降粘防措装置由上、下接头、振动簧片和收缩喷嘴构成。装置安装在抽油泵泵简之下，尾管之上，在压差作用下井下流体以较大速度从装置的喷嘴射出，冲击振动簧片，产生机械振动声波，油水混合液在声波中产生相应的声波力学效应和分散乳化作用等，使混合液在油管内的粘度降低，蜡晶不易聚集长大，从而达到降粘防蜡延长油井热洗周期的目的。室内试验及现场近20口井的应用情况表明，这种装置具有结构简单、成本低廉、应用方便等特点，具有明显的降粘防蜡效果。     

金属－橡胶硫化粘接过程中分子取向行为的间接证据

对金属－橡胶热硫化粘接复合体的剥离行为进行了研究，同一粘接试样的双向１８０°剥离试验显示出了巨大的差异。本文分析了弹性材料在硫化过程中的分子行为，并提出了相应的新假设，认为这是由于金属－橡胶在硫化粘接过程中分子取向交联行为所致。这种双向１８０°剥离破坏现象可被看作是金属－橡胶硫化粘接过程中分子取向行为的间接证据。     

面流消能近底紊动流速特性的研究(面流消能试验研究之一)

本文主要论述了面流消能五种典型流态近底紊动流速特性,总结出了近底时均流速和紊动强度沿程变化规律,提出了近底紊动流速可能出现的最大瞬时值及相应位置的计算公式。面流消能工程的下游防冲设计中考虑的主要水力参数之一是,消能段近底流速紊动可能出现的最大瞬时值及其相应的部位,但目前国内外研究成果较少。笔者通过水工模型试验重点研究了面流消能各典型流态近底流速及其紊动纵向分量沿程的变化规律,并提出了计算公式,为优化面流设计提供科学依据。     

高水头船闸输水廊道反弧门水弹性振动试验研究

本文简要介绍水弹性振动模型试验的相似准则，用近似满足水弹性相似准则的有机玻璃模型对－高水头船闸反弧形阀门进行流激振动试验研究．试验表明阀门的振动是随机振动，不仅有质量振动而且有结构振动，有若干阶模态被激发参与振动。在开门和关门过程中，阀门面板脉动压力和阀门振动是不大的，与葛洲坝船闸类似阀门间歇开启的振动水平相当。由于常压模型不能正确模拟空化现象，对于廊道内可能产生的空泡溃灭所引起的阀门振动尚需通过减压模型进行研究。     

�;��ȶ�����״̬�µ������Ծ���������

本文提出了油井稳定生产状态下的脉冲试井数学模型,利用时间和空间叠加原理求得其解析解。并用非线性回归分析方法来进行脉冲试井分析。     

Physicochemical characteristics and leachability of scale and sludge from Bulalo geothermal system, Philippines

Scale and sludge from Bulalo geothermal field, Philippines, have been characterized by whole rock analysis, radioactivity counting, size analysis, light microscopy, scanning electron microscopy, and X-ray diffraction. Their leachability was assessed by regulatory leaching procedures and by sequential extraction. Both scale and sludge consisted mostly of oxides of Si, Al, and Fe with no radionuclides detected. The scale had 10% S content. Sulfides and silicates were important phases in both samples having size ranges from submicron to 2 mm. Geothermal soils at Bulalo have higher than normal soil levels of As, S, Cu, Cr, Zn, and Pb but regulatory leaching tests indicated that these elements are not released. However, the sequential extraction showed that As, Cu, and Zn were leachable under extreme conditions.     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.