深厚淤泥中双排钢板桩结构安全稳定性研究

针对滨海地区深厚淤泥地基中双排钢板桩围堰结构受力复杂的问题,基于土力学理论,分别从运行工况下的抗剪切变形稳定、底部抗隆稳定、整体抗滑移稳定、抗倾覆稳定以及整体滑动稳定等方面进行分析,给出了安全稳定计算公式,同时通过数学理论推导计算,给出了钢板桩最小入土深度计算公式。以浙江省某大型围垦工程水闸的双排钢板桩围堰工程为例,依据该计算公式,得出最小入土深度建议值为17.01 m,与工程实际设计值18.50 m基本一致;同时利用有限元计算软件,对该工程中双排钢板桩围堰结构进行数值模拟计算分析,并将模拟结果与钢板桩实际水平变位监测资料进行对比分析,认为该双排钢板桩围堰结构设计安全可靠,可为相关工程应用提供参考。     

不同缝纫工艺下缝纫阻力的测试与分析

本文采用LM缝纫性测试仪对不同缝纫工艺下的针织物和机织物缝纫阻力进行了测试.测试了织物层数、织物正反面以及缝纫方向不同时,面料缝纫阻力的大小;测试了不同缝针、缝纫线时的缝纫阻力.实验结果表明:织物的缝纫阻力随织物的层数增加而成倍数以上的增大;机织物在45°角左右缝纫时,缝纫阻力最大;针织物在接近纵行和横列方向,缝纫阻力出现最大值;穿引缝纫线会增大缝纫阻力,但缝纫线对缝纫阻力的增大作用较缝针的作用微弱.同时,实验过程中还发现,针织物的缝纫阻力比机织物的不匀率高,缝针刺到纱线上的概率高,因此针织物不易于缝纫.本论文的研究,希望对服装加工给予帮助,以提高服装质量和服装加工效率.     

基于语文教学中渗透德育教育的探索

语文是基础教育的重要学科,也是思想道德建设的主要阵地。本文将从语文教学过程中如何进行德育教育,如何使学生在学习知识的同时学会做人处事谈一些体会,并就二者的关系以及具体的教学案例进行探讨,旨在从教学方法、情感熏陶、深挖教材这三方面着手进行语文教学中渗透德育教育的经验探索和推广。     

Kinetic analysis of cellular internalization and expulsion of unstructured D-chirality cell penetrating peptides

Most cell penetrating peptides (CPPs) are unstructured and susceptible to proteolytic degradation. One alternative is to incorporate D-chirality amino acids into unstructured CPPs to allow for enhanced uptake and intracellular stability. This work investigates CPP internalization using a series of time, concentration, temperature, and energy dependent studies, resulting in a three-fold increase in uptake and 50-fold increase in stability of D-chirality peptides over L-chirality counterparts. CPP internalization occurred via a combination of direct penetration and endocytosis, with a percentage of internalized CPP expelling from cells in a time-dependent manner. Mechanistic studies identified that cells exported the intact internalized D-chirality CPPs via an exocytosis independent pathway, analogous to a direct penetration method out of the cells. These findings highlight the potential of a D-chirality CPP as bio-vector in therapeutic and biosensing applications, but also identify a new expulsion method suggesting a relationship between uptake kinetics, intracellular stability, and export kinetics.     

CO2激光焊接的同轴检测与熔透控制(Ⅱ)熔透状态同轴光信号的频域分析

利用CO2激光深熔焊等离子体光信号的同轴检测系统,提出了频谱重心的概念井以此来分析等离子体光信号的频谱特性,研究了平扳焊接时对应适度熔透状态时同轴光信号的顿域特征。结果表明,随激光功率增加或焊接速度减小,当焊接熔透状态从“适度熔透(小孔透)”变化到“仅熔池透”时对应2～6kHz段频谱重心位置向上(高额)跳变。     

TIG焊和PAW焊中活性剂对焊缝熔深的影响

针对常规TIG焊生产效率低、熔深小等问题，研究了TIG焊和PAW焊中应用活性剂对焊缝熔深的影响。结果表明，应用活性剂后，在同样的参数下，同传统TIG相比，活性剂能够大幅度提高不锈钢、铝合金和钛合金的焊缝熔深。对于PAW焊，熔深也有增加，但是增加的幅度不如TIG效果明显，但对焊缝成形有很好的改善。同时，活性剂对铝合金焊接背面能够起到保护作用。对于钛合金，活性剂除了增加焊缝的熔深外，还能够大幅度地消减焊缝产生的气孔。     

Prediction and verification of melting front in GTA weld pool of full-penetration

A thermal conduction model is applied to speed up the numerical analysis of the temperature distribution and the weld pool geometry of full penetration in gas tungsten arc （GTA） welding. With considering both top and bottom flee surface deformation of full-penetrated weld pool, three-dimensional weld pool with melting front and solidification front is predicted. Welding experiments are conducted to measure the melting front curves at the top surface and the longitudinal section of the weld. It shows that the predicted and measured results are in good agreement.     

单电源双面电弧焊接工艺实验研究

双面电弧焊接工艺（DSAW）是近几年新出现的一种焊接方法，它可以有效地增大焊缝溶深、提高焊接速度、节约能源消耗、降低焊接变形。本文对单电源DSAW工艺进行了实验研究，分析了双弧作用下焊缝熔深的变化规律，对双面电弧的收缩现象进行了观察，探讨了单电源DSAW工艺增大焊缝溶深的机理。     

Effects of blasting parameters on removability of residual grit

This article shows the quantitative evaluation of the residual grit on a blasted substrate, and the removability of the residual grit is examined. Carbon steel plates were blasted by white alumina grit with mean diameters of 338 to 1106 μm. The velocity and the number of grit particles were measured during blasting. The residual grit was removed from a substrate surface by the dissolution of the blasted substrate surface. A mixed acid solution was used as the dissolution solution. The residual grit weight was 7 to 17 g/m². The amount of the residual grit and the penetration depth of the embedded grit increased with increasing grit size. The penetration depth was 5 to 9% of the mean diameter of the grit. The residual grit weight and the penetration depth increased with the increase of the momentum of the grit particle. This article was originally published inBuilding on 100 Years of Success, Proceedings of the 2006 International Thermal Spray Conference (Seattle, WA), May 15–18, 2006, B.R. Marple, M.M. Hyland, Y.-Ch. Lau, R.S. Lima, and J. Voyer, Ed., ASM International, Materials Park, OH, 2006.     

The integrated intelligent system for welding seam error and penetration depth identification

A integrated intelligent system for seam tracking and penetration control is given. The system received information of welding seam error and penetration depth from only one sensor, then, it realized seam tracking and penetration control simultaneously. This paper introduces constitution of the system, methods of information recognition, design of the neuralfuzzy controller and results practically.