A note on pressure drop for the cross-flow of power-law liquids and air/power law liquid mixtures past a bundle of circular rods

The steady flow of non-Newtonian polymer solutions on their own and together with air transverse to a bundle of circular rods, has been studied experimentally. In particular, the frictional pressure drop has been measured as a function of non-Newtonian power-law constants, flow rates, voidage of bundles and the input fraction of air over wide ranges of conditions as: power-law flow behaviour index, 0.5 to 1; voidage values of 0.78 and 0.87-0.88; air velocity (superficial), 0.09 to 0.28 m/s and liquid velocity (superficial) 0.018 to 0.5 m/s. While the single phase flow results for power-law liquids are in excellent agreement with an existing equation, the two-phase pressure drop results are also in accordance with the form of the well-known Lockhart-Martinelli correlation. Based on these results, it is suggested that a value of 5-10 for the Reynolds number based on rod diameter marks the limit of the laminar flow in such systems.     

A class of discontinuous dynamical systems IV. A laboratory air-water system

An air-water experimental system consisting of two inlets and one outlet is constructed and characterised. It reaches the state of sliding mode, or equivalently, two phase slug flow. The linear hydraulic model proposed in the literature is adequate to describe it. Experimental data are used to tune this model. The resistance to the flow of air through the outlet valve during the two phase flow is much larger than that when air alone flows out. At the operating range, the resistance to water flow is not affected by the presence of air.     

Distribution and nature of organic/mineral bound elements in Assam coals, India

This study focuses on the determination and concentration of twelve elements (Na, K, Ca, Mg, Cr, Mn, Fe, Co, Ni, Cu, Zn and Cd) occurring in sub-bituminous Assam coals and their geochemical association. Distribution of these elements between organic and mineral matters was studied. Comparison of the results of three coals has shown that three elements (Mg, Ca and Mn) are significantly organic bound, while five elements (Fe, Co, Ni, Cu and Zn) are significantly mineral bound; Cd is 50% bound to either organic or mineral matter. FTIR and XRD studies reveal qualitative information about the bonding pattern and nature of components of the mineral matters. The results obtained in this study have considerable geochemical and technological interests.     

Niobium-containing catalysts—the state of the art

This review article is devoted to the materials containing niobium, which have been discovered or developed in the past few years and exhibit the potential application in heterogeneous catalysis. Niobium oxides and mixed oxides as well as sulfides, nitrides (oxynitrides), carbides (oxycarbides), and phosphates are considered. Among the catalytic processes in which Nb-containing materials were tested, liquid and gas phase oxidation is described in details, and the role of niobium in the prevention of the catalyst from SO₂ poisoning is mentioned.     

聚丙烯／轻质碳酸钙／三单体固相接枝物复合体系结构与性能的研究

将聚丙烯与马来酸酐、甲基丙烯酸甲酯、丙烯酸丁酯三种单体的固相接枝物应用于聚丙烯侥质碳酸钙复合体系，研究接枝物对复合体系力学性能、微观形态和耐热性等的影响。结果表明，在PP中加入CaCO3进行填充改性，在一定用量的三单体固相接枝物作用下，PP的力学性能及耐热性得到明显的提高。     

悬浮床催化精馏合成支链烷基苯的模拟

Suspension catalytic distillation (SCD) has been developed recently as an innovative technology in catalytic distillation. In this paper, a brief introduction to SCD is given and an equilibrium stage (EQ) model is developed to simulate this new process for synthesis of linear alkylbenzene (LAB) from benzene and 1-dodecene.Since non-ideality of this reaction system is not strong, EQ model developed could be applied to it successfully.Simulation results agree well with experimental data, and indicate some characteristics of SCD process as an advanced technology for the production of LAB: 100% conversion of olefins, low temperature (90-100℃) and low benzene/olefin mole ratio.     

Control of shrinkage and final conversion of vinyl ester resins cured in low‐temperature molding processes

Vinyl ester resin is a major thermoset polymer used in low‐temperature composite manufacturing processes such as the Seemann composite resin infusion‐molding process (SCRIMP). Volume shrinkage and residual styrene are important concerns for composites produced in such processes. A low‐shrinkage additive (LSA) is a typical agent added to control the volume shrinkage of vinyl ester resins during molding. In this study, the effects of LSA content and the temperature profile (the temperature gradient and peak temperature) on the volume shrinkage control of a vinyl ester resin were investigated. The reaction kinetics of the resin system were also studied. We achieved good volume shrinkage control if we raised the curing temperature slowly to allow sufficient time for phase separation and if the curing temperature reached a high value after phase separation to allow microvoid formation. On the basis of experimental results, we designed an improved SCRIMP to increase resin conversion, reduce resin shrinkage, and produce composites with better properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1486–1496, 2003     

Studies on phase separation rate in porous polyimide membrane formation by immersion precipitation

Phase separation rate during porous membrane formation by immersion precipitation was investigated by light scattering in a polyimide/N‐Methylpyrrolidone (NMP)/water system. In the light scattering measurement, plots of scattered intensity against scattered angle showed maxima in all cases, which indicated that phase separation occurred by a spinodal decomposition (SD). Characteristic properties of the early stage of SD, such as an apparent diffusion coefficient D_app and an interphase periodic distance Λ, were obtained. The growth process of Λ was also followed by light scattering. The growth rate had the same tendency as D_app when water content in the nonsolvent bath and the polymer concentration in the cast solution were changed. The pore size of the final membrane increased with decreasing water content, which was opposite to the tendency of Λ growth rate. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 292–296, 2003     

Porous cellulose acetate membrane prepared by thermally induced phase separation

Microporous cellulose acetate membranes were prepared by a thermally induced phase separation (TIPS) process. Two kinds of cellulose acetate with acetyl content of 51 and 55 mol % and two kinds of diluents, such as 2‐methyl‐2,4‐pentandiol and 2‐ethyl‐1,3‐hexanediol, were used. In all polymer‐diluent systems, cloud points were observed, which indicated that liquid–liquid phase separation occurred during the TIPS process. The growth of droplets formed after the phase separation was followed using three cooling conditions. The obtained pore structure was isotropic, that is, the pore size did not vary across the membrane. In addition, no macrovoids were formed. These pore structures were in contrast with those usually obtained by the immersion precipitation method. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3951–3955, 2003     

Synthesis and characterization of side‐chain liquid‐crystalline ionomers containing quaternary ammonium salt groups

A series of thermotropic side‐chain liquid‐crystalline ionomers (LCIs) containing 4‐(4‐alkoxybenzyloxy)‐4′‐allyloxybiphenyl (M) as mesogenic units and allyl triethylammonium bromide (ATAB) as nonmesogenic units were synthesized by graft copolymerization upon polymethylhydrosiloxane. The chemical structures of the polymers were confirmed by IR spectroscopy. DSC was used to measure the thermal properties of these polymers. The mesogenic properties were characterized by polarizing optical microscopy, DSC, and X‐ray diffraction. Homopolymers without ionic groups exhibit smectic and nematic mesophases. The nematic mesophases of the ionomers disappear and the mesomorphic temperature ranges decrease with increasing concentration of ionic units. The influence of the alkoxy chain length on clearing temperature (T_c) values of ionomers clearly shows an odd‐even effect, similar to that of other side‐chain liquid‐crystalline polymers. The mesomorphic temperature ranges increase with increasing alkoxy chain length when the number of alkoxy carbon is over 3. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2879–2886, 2003