Propane oxydehydrogenation reaction on a VPO/TiO2 catalyst. Role of the nature of acid sites determined by dynamic in-situ IR studies

A VPO/TiO₂ catalyst tested in the oxydehydrogenation reaction (ODH) of propane between 300 and 400°C shows satisfactory performances (up to 80% of propene selectivity at 2% of propane conversion at 300°C or 56% of propene selectivity at 9% of propane conversion at 400°C). Addition of water or pyridine in the feed gas tends to decrease the propane conversion and enhances the propene selectivity. It is shown that water increases the number of Brönsted surface acid sites by dissociative adsorption which, in turn, enhances propene selectivity at the expense of the CO_x selectivity. These results are in good agreement with spectroscopic IR observations performed under catalytic conditions showing that the Lewis acid sites are linked to CO_xformation, whereas it seems that Brönsted sites would rather be linked to propene formation.     

Catalytic wet air oxidation of olive mill wastewater

Au-based catalysts, known for ambient temperature CO oxidation, have to provide stable performance of up to 5000 h in order to be commercially applicable in automotive fuel cells. In this report, the on-line deactivation characteristics of Au/TiO₂ in unconventional PROX conditions are discussed. As opposed to CO removal from air, results in this report suggests that carbonates have a minor effect on deactivation of Au/TiO₂ in dry H₂-rich conditions. Also, no conclusive correlation between surface hydration and deactivation was observed. Rather, deactivation appeared to have occurred as a result of an intrinsic transformation in the oxidation state of the active species in the reducing operating conditions; a process which was reversible in an oxidizing atmosphere.     

Determination of Binder Decomposition Kinetics for Specifying Heating Parameters in Binder Burnout Cycles

The decomposition kinetics of poly(vinyl butyral) binder from barium titanate multilayer ceramic capacitors with platinum metal electrodes were analyzed by thermogravimetric analysis as a function of the heating rate. The activation energy and pre-exponential factor for the decomposition kinetics were determined from two types of integral equations, from the Redhead method, and from the variation in heating rate method. The accuracy of the kinetic parameters determined from these methods was then evaluated for describing the observed rate of binder decomposition. Although the individual models yielded very different kinetic parameters, all were capable of describing the experimental data within ±15% accuracy. The kinetic parameters were then used in a coupled transport and kinetic model for describing the buildup of pressure within the ceramic green body as a function of the heating cycle. A methodology based on calculus of variations was also developed to predict the minimum duration for the binder burnout cycle.     

抄数系统在产品设计和模具制造中的应用

介绍高速抄数机的基本结构、功能、工作流程以及在新产品开发,模具型腔、型芯设计和制造中的具体应用.     

Ozone Contactor Hydrodynamics

Tracer tests were conducted at the 6,000 pounds of ozone per day Tucson, CAP Water Treatment Plant in Tucson, Arizona. The tests were designed to determine T₁₀ values through the contactors at various operating conditions. The tests were modeled using three techniques. Peclet Number was calculated for each of the runs, which would indicate the hydrodynamic conditions inside the ozone contactor. The results indicated that the increase in water flow rate and the number of cells with gas flow increased Peclet Number. The flow rate of liquid seemed to impact the Peclet Number more than gas flow. The headloss in each cell appeared to be important in controlling the distribution of liquid and gas through the cell. A correlation was developed between the product of gas and liquid phase Reynolds Number and Peclet Number.     

An improved light attenuation technique for measuring large interfacial areas

A laser-based light attenuation technique was successfully used to measure interfacial areas as high as 5832 m²/m³ and Sauter mean bubble diameter varying between 50 and 5600 μm. Good agreement between this approach and the photographic technique was obtained particularly at low gas holdups.     

无铅压电陶瓷的研究进展

在压电陶瓷领域，无铅压电陶瓷从环保的角度考虑越来越引起人们的注意。本文主要综述了以BNT为基的3类无铅压电陶瓷体系。它们都是很好的无铅压电陶瓷的侯选材料，其中BNBT－6，BNTN－3和BNST－2的机电耦合常数K33分别为0．55，0．43，而且具有较高的频率常数和较小的介电系数，适用于众多高频超声换能检测领域以及压电致动装置等方面，所以作为无铅压电陶瓷它们是很有潜力的。     

Miniemulsion and conventional emulsion copolymerization of styrene and butadiene: Effect of process on gel content

The properties of styrene/butadiene copolymers obtained by conventional emulsion and miniemulsion polymerizations were studied. Thin layer chromatography with flame ionization detection was used to determine the gel fraction of the copolymer in the latex particles as a function of conversion. It was found that the gel formation began at a higher conversion in the miniemulsion polymerization when compared with that in the conventional process. Also, a lower glass transition temperature was noted at the lowest conversion sampled (～25%), implying a higher initial butadiene monomer concentration within the nucleated miniemulsion monomer droplets when compared with particles formed conventionally. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4616–4622, 2006     

可生物降解热熔胶粘剂的研究进展

综述了近年来可生物降解热熔胶的发展、合成、性能、应用、最新的研究进展。     

Zinc Coated Steel/Epoxy Adhesive Systems: Investigation of the Interfacial Zone by FTIR Spectroscopy

The present study takes advantage of the ability of Fourier Transform Infrared Spectroscopy (FTIR) for the analysis of ultrathin organic films on metals. FTIR in the reflection mode (IRRAS) is used in order to study the interaction of ultrathin films of dicyandiamide (hardener of most one-pack epoxy resins) with various substrates, model ones such as gold or zinc and industrial ones such as steel and zinc-coated steels.

Pure zinc surfaces and, to a lesser extent, zinc-coated steels are shown to react with dicyandiamide after heating at 180°C, as evidenced by the frequency shift of the absorption band (at about 2200 cm^-1) characteristic for nitrile groups. As real systems consist of thick layers of a fully formulated adhesive cured onto a metallic substrate, the direct investigation of such a buried interphase is no longer possible by FTIR and by most of the known spectroscopies. Some mechanically tested specimens are then analysed, after failure, by FTIR microspectrometry. The spectra obtained, corresponding to the fracture initiation zone which is about 100 μm in diameter, advocate for the presence of an ultrathin layer of modified polymer still covering the substrate.