A Finite Element Computational Method for Gas Hydrate. Part I: Theory

A finite element scheme is presented to model the dissociation of gas hydrates in porous media by hot water injection. We show a complete derivation of the finite element formulation, including the associated mass and energy conservation equations capable of performing transient analysis of both conductive and convective heat transfer for gas and liquid flow in porous media. The scheme also includes the latent heat effect to accommodate the change of phase due to melting of hydrate. In the companion paper, Part II, this method is successfully applied to hydrate reservoirs.     

磷酸酯淀粉在纯棉细特高密织物浆纱中的应用

就磷酸酯淀粉在纯棉细号高密织物中的上浆情况进行了试验，提出了具体浆纱工艺和减少织造断头率，提高织物效率及布面质量对策，实验表明，磷酸酯淀粉完全适应于纯绵细特高密织物的上浆要求。     

管壳式换热器流场三维数值模拟

采用多孔介质方法 ,在PHOENICS 3 3程序的基础上建立了换热器的三维流动计算模型。引入体积穿透率、表面穿透率、分布阻力等来描述换热器内的管束。模型通过计算Halle等[1] 的实验工况来进行验证 ,并尝试用于计算 2 0 0MW低温供热堆主换热器内的流场     

P／MCs新型复合材料制备、结构及阻尼性能

采用特殊的渗流法所制备的新型Ｐ／ＭＣｓ复合材料，由高分子聚合物与蜂窝状铝架组成，它具有优异的阻尼性能，并简述了结构对阻尼的影响     

含多孔物质硝胺发射药的温感特性

研究了多孔物质对于硝胺发射药在不同初温下的燃面调节作用，由于多孔物质的孔结构及其与基体界面状况的改变，使发射药低温燃面增大，而高温燃面减小，这有利于降低燃速温度系数．     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

核孔膜生产线膜微孔制备工艺实验研究

本文介绍核孔膜生产线,重点描述了膜微孔制备工艺的实验研究。对于PC和PES膜,已得到32种工况下的扩孔公式,其形式为D=A+Bt,其中D——孔径,t——扩孔时间,A,B为特定工艺参数下的常数值.通过实验。得到了膜孔密度N与300~#核反应堆功率P、热柱辐照位置L的经验公式,即N=6.97×10~5×10~3×101~(1.18L).在本生产线上可生产最大幅面为3 140mm×240mm,孔径为0.04～10 μm的多系列多规格的核孔膜产品。     

Porous elastomeric beads from crosslinked emulsions

The production of porous polymeric particles is attractive for a large number of applications and can be achieved by various techniques. Although numerous production schemes exist for glassy polymers, difficulties arise for soft, rubbery materials that need a chemical crosslinking step, such as elastomers. This is particularly true for poly(dimethylsiloxane) (PDMS), which shows the lowest glass‐transition temperature among the polymers. Recent studies suggest in situ hydrogen bubble formation or vacuum drying of water droplets dispersed in the polymer matrix in order to generate porous PDMS structures. In this work we report early results based on the chemical crosslinking of water in PDMS emulsion droplets in a mechanically stirred thermostated water vessel. This approach is shown to lead to high porosity PDMS beads (ca. 10^?3 m particle diameter) with an open structure whose properties (diameter and porosity) are strongly influenced by the starting composition (solvent, surfactant, and polymer types and ratios), as well as the operating parameters (agitation and temperature). The possible uses of these derived beads are discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 967–971, 2002     

Asymmetric alumina membranes electrochemically formed in oxalic acid solution

Alumina membranes were fabricated by anodizing aluminium metal in 0.15 M oxalic acid. The growth kinetics of the porous layer were investigated in the temperature range –1 to 16 °C using linear potential scans up to 70 V. The faradaic efficiencies of metal oxidation and of porous layer formation, determined by applying Faraday's law, were found to be independent of both temperature and electrical charge. SEM analysis of the metal-side and solution-side surfaces revealed different morphologies. After dissolution of the barrier layer in phosphoric acid, the metal-side surface showed circular pores whose size of about 90 nm was found to be uniform and independent of temperature. The pore population was also practically independent of temperature and a value of about 4 × 10¹³ pores m^–2 was determined. On the solution-side surface the presence of a deposit partially occluding the mouths of pores was observed. This coating could be removed by chemical etching in NaOH or thermal treatment at 870 °C, where decomposition of oxalate occurs. This supports the hypothesis that the deposit consists of an aluminium salt containing oxalate anions precipitated from the solution. The results show that it is possible to control the morphological characteristics of the anodic alumina membranes by careful choice of experimental conditions.     

Advances in Microporous and Mesoporous Solids—Highlights of Recent Progress

This report highlights developments in the fields of microporous and mesoporous materials that were published mostly during the year 2002. Selected examples are provided to illustrate new zeolite structures, porous coordination materials, mesoporous solids with new compositions, controlled morphologies, and increased hydrothermal and thermal stabilities, as well as porous solids with tunable pore openings or other structural features that can be dynamically modified. A number of applications are discussed, including stabilization of reactive guests, separations, electronic materials, and sensors.