Heat Transfer Analysis for Gas-to-Liquids Transportation Through Trans Alaska Pipeline

Gas-to-liquids (GTL) technology involves the conversion of natural gas to liquid hydrocarbons. In this article, theoretical studies have been presented to determine the feasibility of transporting GTL products through the Trans-Alaska Pipeline System (TAPS). To successfully transport GTL through TAPS, heat loss along the route must be carefully determined. This study presents heat transfer and fluid dynamic calculations to evaluate this feasibility. Because of heat loss, the fluid temperature decreases in the direction of flow and this affects the fluid properties, which in turn influence convection coefficient and pumping power requirements. The temperature and heat loss distribution along the pipeline at different locations have been calculated. Fairly good agreement with measured oil temperatures is observed. The powers required to pump crude oil and GTL individually, against various losses have been calculated. Two GTL transportation modes have been considered; one as a pure stream of GTL and the second as a commingled mixture with crude oil. These results show that the pumping power and heat loss for GTL are less than that of the crude oil for the same volumetric flow rate. Therefore, GTL can be transported through TAPS using existing equipment at pump stations.     

The influence of raw material characteristics on the industrial pelletizing process and pellet quality

Industrial pelletizing of sawdust was carried out as a designed experiment in the factors: sawdust moisture content, fractions of fresh pine, stored pine and spruce. The process parameters and response variables were energy consumption, pellet flow rate, pellet bulk density, durability and moisture content. The final data consisted of twelve industrial scale runs. Because of the many response variables, data evaluation was by principal component analysis of a 12 × 9 data matrix. The two principal component model showed a clustering of samples, with a good reproducibility of the center points. It also showed a positive correlation of energy consumption, bulk density and durability all negatively correlated to flow rate and moisture content. The stored pine was more related to high durability and bulk density. The role of the spruce fraction was unclear. The design matrix, augmented with the process parameters was a 12 × 6 matrix. Partial least squares regression showed excellent results for pellet moisture content and bulk density. The model for durability was promising. A 12 × 21 data matrix of fatty- and resin acid concentrations measured by GC–MS showed the differences between fresh and stored pine very clearly. The influence of the spruce fraction was less clear. However, the influence of the fatty- and resin acids on the pelletizing process could not be confirmed, indicating that other differences between fresh and stored pine sawdust have to be investigated. This work shows that it is possible to design the pelletizing process for moderate energy consumption and high pellet quality.     

电力负荷削峰减载系统在珠钢电炉的应用

借助现场采集装置,在计算机上获取每一分钟的冶炼工艺电能需求量,显示当前15分钟时段已发生的电耗量,调整用户设定,实现需量自动刷新、报警和专家分析推荐后续用量;实现平稳用电并减少对电网冲击,同时降低电能最大需用量以减少成本。     

新型水泥浆实心减轻材料FXW在固井中的应用研究

低密度水泥浆常用泡沫和漂珠作为减轻材料，但泡沫和漂珠的一个共同缺陷是承压能力有限。在现场使用时，地面密度和井下密度是不一致的，这将打破注水泥压力平衡，给固井施工带来一定的风险。为此，通过大量实验，根据颗粒紧密堆积原则，以粉煤灰、改性橡胶粉、微硅、石灰类矿物等为原料，复配出一种新型实心耐压减轻材料 FXW 。由于FXW为实心减轻材料，能够承受压力，因而能够适应井下高压条件。实验表明，FXW低密度水泥浆强度高，韧性好，可更好地满足油气井后期开发需求。     

3-D MCM封装技术及其应用

介绍了超大规模集成电路（VLSI）用的3-D MCM封装技术的最新发展，重点介绍了3-D MCM封装垂直互连工艺，分析了3-D MCM封装技术的硅效率、复杂程度、热处理、互连密度、系统功率与速度等问题，并对3-D MCM封装的应用作了简要说明。     

粉煤灰降失水水泥浆在天然气井固井中的研究与应用

长庆天然气田属于低压、低渗透气田,存在承压能力较低的地层,固井设计要求全井段封固,并且采用双级双凝施工工艺。但由于用于低密度水泥浆中的漂珠生产量降低,价格上升,研究应用替代产品是固井技术发展的方向。在一级领浆中研究应用了粉煤灰水泥浆体系,其性能和固井质量可完全满足固井要求。粉煤灰水泥浆体系价格低和固井质量优良,使其成为漂珠水泥浆体系的替代配方。     

The Minimum PAPR Code for OFDM Systems

In this letter, a block code that minimizes the peak‐to‐average power ratio (PAPR) of orthogonal frequency division multiplexing (OFDM) signals is proposed. It is shown that peak envelope power is invariant to cyclic shift and codeword inversion. The systematic encoding rule for the proposed code is composed of searching for a seed codeword, shifting the register elements, and determining codeword inversion. This eliminates the look‐up table for one‐to‐one correspondence between the source and the coded data. Computer simulation confirms that OFDM systems with the proposed code always have the minimum PAPR.     

Carbon nanofibers as hydrogen adsorbing materials for power sources

Porous carbon nanofibers are synthesized by CVD method from acetylene with use of iron-containing catalysts. Activation of the nanofibers in melted potassium hydroxide results in increasing surface area from initial 300–400 m² g⁻¹ to 1700 m² g⁻¹. As follows from XRD data, activated nanofibers do not contain regular packages of graphene layers, but retain high electric conductivity. Deposition of copper improves electrochemical hydrogen storing characteristics of carbon nanofibers. Carbon nanomaterials obtained can be used as hydrogen storing materials in batteries instead of hydride forming metals.     

32位MIPS微处理器中乘法器的设计和实现

在Booth算法的基础上,结合MIPS 4KC微处理器中的流水线结构和乘法器的工作过程,提出了一种改进的Booth乘法器的设计方法,并采用全制定方法实现,用这种方法实现的乘法器单元具有面积小、单元电路可重复性好、版图设计工作量小、功耗低等特点.     

CDMA系统中联合功率控制、波束赋形与多用户检测

应用功率控制、波束赋形和多用户检测可以有效地消除和减少CDMA系统中的干扰。本文结合波束赋形和多用户检测的特性，提出一种应用波束赋形增益和多用户相关矩阵的解相关算法。基于算法的复杂性，提出一种区分聚集用户进行多用户检测的的算法。由于波束赋形能够消减主瓣波束之外的多用户干扰，对聚集移动台采用解相关检测达到减少运算量和消除多用户干扰的目的。对算法进行了仿真分析，证明了本算法的优越性。