用小尺寸R－CT试样研究核压力容器钢断裂韧性及与Charpy试样的比较

提出了一种用双边带深侧槽的小尺寸圆形紧凑拉伸试样评定核压力容器（ＲＰＶ）钢断裂韧性的单试作试验方法，给出了用该方法测定的两个厂家生产的核压力容器用Ａ５０８ＣＬ３钢的断裂韧性参数，还与Ｃｈａｒｐｙ试样的试验结果及大尺寸标准试样的试验结果进行了比较。研究结果表明：用双边带深侧槽的小尺寸Ｒ－ＣＴ试样测得的断裂韧性值比相同恻槽深度预制疲劳裂纹Ｃｈａｒｐｙ试样的测试值更接近有效断裂韧性值，所以，用于核压力容器断裂韧性的监测是可行的。     

用试井方法确定注水后地层渗透率的变化

大港油田已进入开发中后期，高含水油田占73％，开发初期的一些参数已不适合现在开发的需要。研究出一套用试井方法确定注水以后地层渗透率变化的方法，对大港油田的增储上产具有重要意义。     

CMOS电路中抗Latch-up的保护环结构研究

闩锁是CMOS集成电路中的一种寄生效应,这种PNPN结构一旦被触发,从电源到地会产生大电流,导致整个芯片的失效。针对芯片在实际测试中发现的闩锁问题,介绍了闩锁的测试方法,并且利用软件Tsuprem4和Medici模拟整个失效过程,在对2类保护环(多子环/少子环)作用的分析,以及各种保护结构的模拟基础之上,通过对比触发电压和电流,得到一种最优的抗Latch up版图设计方法,通过进一步的流片、测试,解决了芯片中的闩锁失效问题,验证了这种结构的有效性。     

压裂泵往复密封性能及机理研究

根据流体动压润滑理论，对压裂泵柱塞密封摩擦副的润滑机理进行了理论分析。在排出和吸入行程，柱塞密封摩擦副均能满足流体动压润滑的条件，即在柱塞与密封界面上能形成并保持一定厚度的油膜润滑密封，从而达到减小摩擦提高寿命的目的；建立了摩擦界面油膜厚度和泄漏量的计算公式。利用有限元法理论，对密封圈的压力沿轴向的分布规律、泄漏量与压力变化关系进行了模拟计算。对往复密封圈沿轴向压力分布、泄漏量随压力变化进行了测试；试验结果表明，建立的计算模型具有较高的计算精度，揭示了压裂泵的密封机理。     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

p,V, T and derived thermodynamic data for toluene,trichloromethane, dichloromethane,acetonitrile, aniline,and n-dodecane

Experimentally determined p,V,T data are reported for toluene, trichloromethane, dichloromethane, acetonitrile, aniline, and n-dodecane at 278, 288, 298, 313, and 323 K, except for dichloromethane, for which the highest temperature was 298 K. At each temperature, measurements were done at pressures up to about 280 MPa or (for aniline and n-dodecane) at a lower pressure slightly below the freezing pressure at the temperature of measurement. Values of the isobaric expansivity isothermal compressibility and (for toluene, trichloromethane, dichloromethane, and acetonitrile) internal pressure, derived from the p,V,T data, are presented.     

高压低温先导式安全阀的设计

介绍了一种某试验系统用高压低温先导式安全阀,主要从工作原理、结构特点、材料的选用、结构特点、试验等方面进行阐述。     

55t/h锅炉技术改造成功经验

介绍了35t／h锅炉扩容改造为55t／h非标锅炉的技术成功经验。从增加锅炉的容积、受热面面积、燃烧器喷嘴改造三个方面介绍了对锅炉本体的改造，改造后实现了锅炉的水位、汽温及燃烧自动调节，提高了锅炉的热效率为以后的锅炉扩容改造提供了实践经验。     

利用测井资料预测塔河油田地层破裂压力

针对塔河油田奥陶系碳酸盐岩油藏 ,介绍了地层破裂压力预测和地层裂缝高度预测的基本原理 ,选择了塔河油田 4口井的资料进行了破裂压力和裂缝高度预测的成果处理。为塔河油田奥陶系碳酸盐岩储层改造提供了较为可靠的施工参数     

Case Study of an Aerosol Explosion and a Method to Determine Explosion Temperatures

A failure analysis case study is presented for a two-piece aerosol containing tetrafluoroethane, commonly referred to as Refrigerant 134a. A gentleman was preparing to recharge the air conditioning system of an automobile when the bottom exploded off the aerosol container, propelling the body of the aerosol container like a rocket, which hit the man in the eye and blinded him in that eye. The aerosol was never connected to the air conditioner, therefore backpressure from the air conditioner (AC) compressor was ruled out as a cause for the explosion. The objective of the study was to determine why the aerosol exploded. Several recently developed test methods were used, including two types of heat-to-burst tests and a puncture chamber to measure the pressure-versus-temperature behavior of aerosols. More common test methods were also used, such as water bath pressure tests, hydro pressure burst tests, pneumatic pressure burst tests, hardness measurements, weight measurements, metallography, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and an accident scenario recreation. A semi-empirical correlation between the hardness and weights of the container bottoms was used to determine the explosion temperature and/or pressure. This semi-empirical correlation agrees in principle with an analysis of the explosion pressures using finite-element analysis (FEA). The root cause for the explosion was determined to be a lack of strength of the bottom of the two-piece aerosol coupled with heating the aerosol to temperatures significantly above room temperature.