Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

人支气管上皮靶细胞形态学参数的测量

支气管上皮靶细胞形态学参数对计算受氡子体照射的支气管的剂量是很重要的。本文介绍利用奥尔新兰-PAS 染色的外科切除人肺组织切片,测量基底细胞粘液细胞和的胞核深度与数目。结果表明,叶、段和小支气管的粘液细胞核深度分别为相应节段基底细胞的61%、69%和73%;此三节段粘液细胞的数目分别为基底细胞的53%、29%和28%,平均为37%。     

压水堆核燃料循环的经济分析程序介绍

所开发的压水堆核燃料循环分析计算机经济程序包括12个子程序,代表着压水堆整个核燃料循环各种不同的工艺过程。本程序能算出压水堆核电站核燃料循环中燃料费用对发电成本的影响,给出各工艺过程对燃料成本的敏感度分析,并尽可能给出燃料循环中燃料材料及服务的价格数据.     

论社区服务产业化

社区经济作为一种优化的资源配置方式，利用社区服务为载体，将社区内互不相联的各种经济成份变为利益共同体，建立一种新的经济生产方式，从而带动社区乃至更广区域的经济发展。     

Prediction of spectral reflectance factor distribution of automotive paint finishes

It is necessary to determine the accurate reflectance of painted surfaces for the review of paint finishes by computer graphics (CG) before actual painting of the exterior color of automobiles, and for quality control during production and inspection processes. We have optimized a method for measuring reflectance by using a statistical technique. We have found that the reflectance of a painted surface is best measured at an incident angle of 60° and at five aspecular angles of 10°, 18°, 28°, 40°, and 90°. Our method makes it possible to accurately reproduce reflection characteristics of paint finishes containing special flake pigments, such as pearl mica. Also it was proved that our method can apply not only to solid and metallic coatings but to all painted surfaces. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 275–282, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20125     

Drying of Uncoated Paper with Gas-Fired Infrared Emitters—Optimum Emitters' Location Within a Paper Machine Drying Section

This article theoretically investigates the drying of uncoated paper with gas-fired infrared (IR) emitters installed within the drying section of a given commercial paper machine. Specifically, it presents the ideal location of two opposing IR emitters within the drying section. The ideal location of the two opposing IR emitters corresponds to the highest machine speed with specified average moisture content of paper sheet at the end of the drying section. This article also presents the average evaporation rate, temperature, and moisture content of the paper sheet as it travels through the drying section with the two opposing IR emitters operating at the optimum location. In addition, the temperature and moisture profiles in the sheet thickness direction, before and after the IR emitters, are provided. This article is not concerned with the potential effects of drying with IR emitters on paper sheet properties and machine runnability issues.     

铝型材推弯工艺

通过铝型材圆环的推弯实验,研究了推弯工艺原理、变形过程,结合有限元模拟得到了和实验结果相吻合的型材厚度分布、成形零件卸载回弹后的曲率半径及型材截面畸变.结果表明:推弯零件曲率及截面畸变一致性高,成形模具结构简单且便于调整,数值模拟可以用于推弯工艺的优化分析.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

Robustness of VS-MRAC with respect to unmodelled dynamics and external disturbances

A variable structure model reference adaptive controller (VS-MRAC) using only input and output measurements was recently proposed and shown to be globally asymptotically stable with superior transient behaviour and disturbance rejection properties. In this paper a singular perturbation approach is used in order to establish the robustness of the controller in the presence of unmodelled dynamics (parasitics) and disturbances. We develop a new Lyapunov-based technique to analyse the overall system and show that for sufficiently small parasitics the system remains stable and the output error is small in some sense.