AA7005铝合金的热加工变形特性

研究了AA7005合金高温压缩变形时的流变应力、动态回复与再结晶以变形组织变化特征。合金稳态变形时,应变速度、温度和流变应力之间满足包含热激活材料常数的Arrhenius项的双曲正弦关系,变形过程为受位错增殖和相互销毁速率控制的热激活过程,螺型位错的交滑移和刃型位错的攀移为主要动态回复机制。动态回复时,形成典型的变形亚晶组织,亚晶尺寸随1nZ的减小而增大。高温低速变形条件下,合金发生局部几何动态再结晶,流变曲线呈现连续下降的特征,形成与原始纤维组织不同的细小等轴大角度再结晶晶粒。     

TA15合金的热变形行为及加工图

研究了TA15合金的热模拟压缩实验。结果表明：变形温度的升高和应变速率的减小使峰值应力和稳态应力显著降低，变形温度会影响进入稳态流动所需变形量。以热模拟压缩实验为基础，建立的加工图表明：TA15合金高温变形时存在2个非稳定区域，一个是变形温度1300K以上和应变速率10．0s^-1以上的区域，另一个是变形温度1200K以下和应变速率0．006s^-1～1．995s^-1之间的区域。同时，建立的TA15合金高温变形时的流动应力模型表征了变形温度、应变速率和变形程度对流动应力的影响，模型的计算精度较高。     

基于字典的DNA序列压缩算法研究及应用*

在现有DNA序列数据压缩算法的基础上,以DNA序列数据的存储效率及生物学解释综合考虑,设计并实现了基于字典的DNA序列压缩算法DNADCompress.算法核心包括重复子串字典建立、字典项筛选、字串压缩编码三方面.实验数据表明,数据压缩算法压缩效果达到常用DNA序列压缩算法水平,并为序列生物学解释提供了基础.     

经不同熔体处理的易拉罐用铝材的热压缩变形组织

采用动态热/力模拟实验技术对经不同熔体处理的易拉罐用铝材进行高温压缩变形实验,并用光学显微镜、透射电镜分析探讨其热变形组织特征。结果表明:冶金质量影响易拉罐用铝材的动态再结晶组织特征,在未处理或常规熔体处理状态下存在枝晶网胞结构,晶粒组织不均匀;高效熔体处理使易拉罐用铝材在较低的温度下即可通过亚晶合并方式发生动态再结晶,并在变形温度573~673 K、应变速率0.1~1.0 s-1、变形量约0.7的较宽的热变形工艺条件下可获得细小且分布较均匀的再结晶晶粒组织。     

Flow stress and softening behavior of wrought magnesium alloy AZ31B at elevated temperature

1　INTRODUCTIONThewroughtmagnesiumalloyshaveexcellentspecificstrengthandstiffness ,machinability ,dampcapacity ,dimensionalstability ,lowmeltingcostsandare ,hence ,veryattractiveinsuchapplicationsasau tomobile ,aviation ,electronicandcommunicationin dustry[16 ] .Investigationsontheflowstressandsofteningbehaviorofmagnesiumalloysathigherformingtem peratureandstrainratehavebeenanimportantsub jectinwroughtmagnesiumalloysforming[710 ] .InthispapertheflowstressandsofteningbehaviorofAZ31Bdeform…     

Aging and mechanical properties of NR/BR blends

The mechanical properties and post-thermal aging properties of natural rubber (NR) and polybutadiene rubber (BR) blends at different blending ratios are investigated herein. The experimental results show that both tensile and tear strengths of NR/BR blends increase with increasing NR content. BR has a higher compression stiffness than NR. The deformation of BR is less than that of NR under the same load conditions. With regard to aging properties, both tensile stress and strain of NR/BR blends decrease after prolonged aging. In addition, the stress loss of BR is lower than that of NR, meaning that the aging resistance property of BR is superior to that of NR. Furthermore, accumulated thermal history has shifted the glass transition temperature (T _g) of NR/BR blends toward lower temperatures while the loss tangent (tan δ) value increases with prolonged thermal aging.     

铸态AZ80镁合金高温热变形行为研究

在Gleeble-1500热模拟机上对铸态AZ80镁合金在应变速率为0.005s-1~5s-1、变形温度为200℃~400℃条件下的高温热压缩变形行为进行了研究。结果表明,材料真应力-真应变曲线呈现动态再结晶特征。在温度T≥250℃,试样流变应力行为对应变速率敏感;在低温下T=200℃,应变速率对流变应力影响不大。高温下试样流变应力符合幂指数函数关系,应力指数n为6,热变形激活能Q为220kJ/mol。在高应变速率条件下,试样在变形中的温升是应变量的函数。实验中,Zener-Hollomon参数值大的试样温升明显,而Zener-Hollomon值小的试样变形温度基本保持不变。     

小波分析与漏磁检测信号处理

详细介绍了小波分析的基本理论,并将其引入到钢管漏磁探伤信号的分析中,可以去除噪声、压缩数据和检测奇异性,而且为缺陷的定性和定量分析提供了新的判定方法.     

Effect of temperature on mechanical behavior of AZ31 magnesium alloy

Strain rate sensitivity and tension/compression asymmetry of AZ31 magnesium alloy at different temperatures and strainrates were investigated.Both of mechanical behaviors are temperature dependent.Strain rate sensitivity increases with increasingtemperature.Thermally activated slip is the source of strain rate sensitivity.At the temperature below or near 373 K,strain ratesensitivity is very little.Tension/compression asymmetry in yielding decreases with increasing temperature.Twinning is the reasonof tension/compression asymmetry.At the temperature above or near 573 K,the material shows little tension/compressionasymmetry of the flow stress.     

Study on the machinability of resulfurized composite free-cutting steels

The machinability of S, S-Ca, S-RE, and S-RE-Ca system resulfurized composite free-cutting steels were investigated, where RE is rare earths, mostly cerium. The experimental results showed that in the low cutting speed range (≤35 m/min), the S-RE system free-cutting steel had better machinability than the others and that the S-RE-Ca system free-cutting steel exhibited the best machinability at high cutting speeds. A protective layer capable of preventing diffusion wear was formed on the rake face of a P30 tool when S-RE-Ca system free-cutting steel was machined in the cutting speed range of 120 to 160 m/min.