小冲孔蠕变试验技术

小冲孔蠕变试验技术是获取在役构件蠕变性能的一种新方法，由于它具有接近无损取样的特点，因此受到学术界和工业界的广泛重视。本文简要回顾了小冲孔蠕变试验技术的发展及应用，重点介绍了典型小冲孔蠕变试验装置的组成及结构，指出了小冲孔蠕变试验技术目前存在的问题和广阔的应用前景。     

基于并行工程和网络计划技术的模具生产进度编制方法

在充分考虑模具生产的特点和生产活动之间并行性的基础上,建立了单副模具典型生产过程的细化网络图,提出了一种基于并行工程、网络计划技术和最优化生产技术(OPT,Optimal ProductionTechnology)的模具生产进度计划编制方法。通过算例及其结果分析,表明了方法的可行性和有效性。     

优质、高效电弧喷涂技术的应用和发展

本文介绍了电弧喷涂技术的原理、特点，在生产中的应用和发展，国内在研究和应用方面存在的差距，该技术的发展方向。     

无损检测的几个热点问题和技术

介绍当前无损检测领域几项快速发展的并受人普遍关注的热点问题和技术，如输油、输气管道和地下管网的在线监测、复合材料粘接层的检测、成像技术以及信号处理。介绍其基本原理、技术特点和近期进展。最后指出，当前新材料新领域的质量控制发展对无损检测技术提出了更高的要求和更广阔的应用空间。     

Study On the Tribological Behavior of the Arc-added Glow Discharge Plasma Non-hydrogen Carburization On Titanium Alloy Surfaces

This paper introduces a new titanium alloys surface strengthening treatment by using the arc-added glow discharge plasmas non-hydrogen carburization technique. High purity and high strength graphite is selected as cooling cathode arc source for supplying carbon atoms and particle, which migrate to the titanium alloy(Ti6Al4V) surface and form modified layer. Thus, the hydrogen embrittlement is avoided while the tfibological behavior of the titanium alloy surface is improved in the respects of anti-friction and anti-wear ability.The tribological behavior of the modified layer under dry sliding against SAE52100 steel was evaluated on a ball-on-disc test rig. The results showed that the modified layer obtained a thickness of 30μm at 980℃, 30minutes. The microhardness of the Ti6Al4V alloy surface attained 936 HV, which was much larger than that of the Ti6AI4V alloy. The Ti6AI4V alloy was characterized by adhesion wear and scuffing under dry sliding against the steel, while the surface modified layer experienced much abated adhesion wear and scuffing under the same testing condition. This could be attributed to the carbon dement with different modalities exists in the modified layer.The modified layer showed good friction-reducing and fair anti-wear ability in dry sliding against the steel. Using the SEM,XRD and XPS, the phase structure and morphology of the carburization modified layer was analyzed.     

板料成形优化技术进展与质量工程研究

板料成形过程的优化研究对于改进模具设计、提高产品质量具有重要意义。综述了板料成形工艺优化的研究现状。考虑到在有约束的设计优化中,最优结果常位于约束边界附近,随机因素的波动易导致产品质量不稳定甚至失效,难以保持产品的可靠性和稳健性。为此,本文应用质量工程学中的6σ理念,提出了基于数值模拟的板料成形6σ稳健设计优化方法。     

倾斜冷却体法制备半固态浆料的研究现状

介绍了低成本、高效率的倾斜冷却体法制备半固态浆料的方法，综述了国内外对该方法的研究现状、相关工艺参数对组织形貌的影响及需要解决的关键问题。     

EPS模陶瓷型精密铸造失模工艺研究

针对EPS陶瓷壳型精铸失模时容易裂壳的现象,对EPS消失模精密铸造工艺进行了研究。利用自制的膨胀率检测设备对不同密度的EPS模试样在不同加热温度下的最大膨胀率进行了测试,研究了壳型膨胀与失模温度之间的关系;对陶瓷壳型中EPS模失模时的温度场分布进行测量,发现EPS模试样的密度大小对失模时温度场有着很重要的影响。在试验和分析的基础上,对EPS模失模机制进行了探讨,提出了高温失模机制。高温失模有利于降低失模时对壳型的膨胀作用力,为获得洁净而健全的陶瓷型壳提供了可靠保证。     

The role of the surface free energy in the selection of a suitable excipient in the course of a wet-granulation method

Pellets containing metronidazole were produced in a centrifugal granulator, with hydroxypropylcellulose (Klucel LF®) as binding agent, and corn starch, microcrystalline cellulose (Vivapur 101®) and lactose as excipients. The wettability of the pharmaceutical powders was assessed by means of contact angle measurements, and the dispersive and polar surface energies were determined. The spreading coefficients, the work of adhesion and the work of cohesion were calculated and correlated with the pellet properties (friability, bulk and tapped density, and porosity). The aim was to investigate the role of the surface free energy of one- and two-component powder compositions in pellet production. The interactions between the particles were found to be connected with the measured pellet parameters. It was concluded that, in the course of the growth of the pellets, the particle sizes of the pharmaceutical powders and the interactions between them are important. If the work of cohesion of the binder is lower than the work of cohesion of the substrate and the work of adhesion, then the optimal amount of the binding agent is that which coats the particles uniformly in minimal quantity and in continuous layer.