Prediction of higher heating values for saturated fatty acids from their physical properties

Higher heating values (HHVs) of fatty acids (C₄–C₁₈) were measured and correlated using linear least square regression analysis. Equations were developed for the estimation of the HHVs of saturated fatty acids from their molecular weight (Mw), density (DN) and carbon number (CN). These equations are HHV = 0.0518 Mw + 29.76, HHV = −93.4 DN + 122.67 and HHV = 0.7271 CN + 31.419 with R² values of 0.9895, 0.9798, and 0.9895, respectively. The correlations may be used for HHV estimation of mixtures of fatty acids developed from vegetable oils.     

Visualization and quantification of the mechanical deformation induced by an electrical field in poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) films

An optical nondestructive strain measurement technique was performed to analyze the mechanical deformation induced by an electrical field within the insulating materials. Poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) films were then subjected to constant electrical fields right up to their electrical breakdown. The experimental technique made it possible to follow the various stages of the mechanical behavior of PEN in real time. The final breakdown occurred in the observation zone and the related mechanical deformation was captured. A “margarita” structure was observed with a hole at the center. The experimental results indicated that the level of the induced‐mechanical deformations depended on the local environment. We defined two different zones representing the inside and the outside of the damaged area. The induced‐deformations were larger in the damaged zone. It was also observed that deformations increased when the sample had a lower degree of crystallinity. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyurethane foams with 1,3‐pyrimidine ring

Attempts of obtaining of polyurethane foams using polyetherols with 1,3‐pyrimidine ring (obtained in reactions of 6‐aminouracil with oxiranes) are reported. Properties of the foams are investigated, especially their thermal stability. The foams show an improved thermal stability up to 200°C for a long time. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal stabilization effect of biphenol monoacrylate on polyamide 6

Biphenol monoacrylate (AL) was combined with a traditional hindered phenolic‐based binary antioxidant system to form a ternary stabilization system for the purpose of further improving the thermal–oxidative stability of polyamide 6 (PA6). The thermal stabilization effect of the antioxidant AL on PA6 was studied in terms of the reduced viscosity, the chemical structure, the yellow index, and the mechanical properties. The results showed that the antioxidant AL, with the proper chemical structure, could improve the thermal stability of PA6 effectively through a unique bifunctional stabilizing mechanism. The interaction of the molecules of PA6 with the antioxidant AL was investigated. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Entanglement network and relaxation temperature dependence of single‐site catalyzed ethylene/1‐hexene copolymers

In this work, we investigate the linear viscoelastic response of high molecular weight ethylene/1‐hexene copolymers, characterized by a narrow molecular weight distribution and comonomer content in the range from 0 to 10 mol %. A variation in the entanglement plateau modulus has been found in agreement with the recently developed packing length model. The packing model applied to viscoelastic data suggests decreased values of the characteristic ratio, accordingly with recent computer simulation results. The flow activation energy increases as the side chain content increases. This feature is thought to be related to the mobility of the molecules. The presence of side branches due to the comonomer hinders the mobility of the molecules, and increases the thermal barrier for the segmental motion. Then in the comonomer content range studied, the increase of the flow activation energy goes parallel with a decrease in the characteristic ratio. This result suggests that more parameters than only the stiffness of the chain modulate the thermal dependence of viscoelastic properties. A more refined study is necessary combining experiments with computer simulations in order to elucidate these aspects. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influence of the amount of ferromagnetic addition on the rheological properties of spinning solutions,the structure,the strength,and thermal properties of polyacrylonitrile fibres

The rheological properties of spinning solutions of polyacrylonitrile in dimethyl formamide (DMF) containing various amounts of a ferromagnetic nanoaddition were investigated. The porous structure, the strength and thermal properties of fibers obtained from these solutions were assessed, as well as the uniformity of the nanoaddition distribution on the fiber surface was estimated. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Green and self-lubricating polyoxymethylene composites filled with low-density polyethylene and rice husk flour

Polyoxymethylene (POM) composites filled with low-density polyethylene (LDPE) and rice husk flour (RHF) were prepared by injection molding. The POM/5 wt % LDPE/7.5 wt % RHF composite exhibited the lowest wear rate, whereas the coefficient of friction remained low, and the POM/5 wt % LDPE/5 wt % RHF composite had the best mechanical properties. X-ray diffraction analysis was carried out, and the worn surfaces were examined with scanning electron microscopy. The results showed that the addition of the filler reduced the crystallinity degree of the POM composites. The main wear mechanism for unfilled POM was adhesion, whereas for the POM composites, wear seemed to occur mainly by fatigue and abrasion. It was experimentally confirmed that the POM composite filled with LDPE and RHF, which is well-performing, low-cost, and environmentally friendly, could be a potential material for tribological applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Epoxidation of high trans‐1,4‐polyisoprene and its properties

A new organic‐solvent‐free water‐phase suspension method was used to synthesize partially epoxidized high trans‐1,4‐polyisoprene (TPI) to improve its properties, including oil resistance and wet‐skid resistance. The epoxidation was conducted in an aqueous peracetic acid solution and on the TPI granules prepared by a bulk precipitation method with supported titanium catalyst. The effects of the synthesis conditions, including reaction temperature, reaction time, and pH value, on the epoxy content were investigated. Epoxidized trans‐1,4‐polyisoprene (ETPI) with epoxy contents between 10 and 80% were obtained within 4 h. Both the amorphous and crystalline regions of TPI were epoxidized. The crystallization properties decreased with increasing epoxy content. ETPIs possessed lower mechanical properties than TPI but could be enhanced by vulcanization. The oil resistance and wet‐skid resistance were significantly improved after epoxidation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Local dynamics in epoxy coatings containing iron oxide nanoparticles by dielectric relaxation spectroscopy

Nanocomposites of photocurable epoxy resin and epoxy‐modified iron oxide magnetic nanoparticles were analyzed by dielectric relaxation spectroscopy to study the local dynamics at temperatures well below the glass‐transition temperature. Two secondary processes were detected, β and γ processes, but the second one was just detected at lower temperatures in the high‐frequency part of the spectra and moved out of the frequency range at higher temperatures. Data were fitted to the Havriliak–Negami and Arrhenius models, and the obtained parameters were analyzed. Relaxation times of the β secondary relaxation did not change with the nanoparticle content, but the relaxation strength increased. The increase could not be explained when we took into account the molecular origin of the relaxation. The presence of ferromagnetic nanoparticles enhanced the internal field and increased the relaxation strengths. Transmission electron microscopy images showed that the nanoparticles were well dispersed in the matrix, without magnetic agglomerates. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Influence of post‐treatments on the properties of porous poly(vinyl alcohol) membranes

Porous poly(vinyl alcohol) (PVA) membranes were prepared by a phase‐inversion method. The influence of chemical crosslinking and heat treatments on the swelling degree, resistance to compaction, mechanical strength, and morphology of porous PVA membranes was extensively studied. The crosslinking degree and crystallinity of the membranes, calculated from IR spectra, increased with the treatment time. The porosity, calculated on the basis of swelling experiments, showed a decreasing trend for heat‐treated membranes but remained almost at a constant value for crosslinked membranes. Such a change was further proved with scanning electron microscopy pictures. The behavior was explained by the rearrangement of PVA chains during the heat‐treatment process, which led to morphological changes in the membranes. The mechanical properties of the porous membranes in dry and wet states were measured, and a great difference was observed between crosslinked and heat‐treated membranes in the dry and wet states. The crosslinked membranes showed good mechanical properties in the dry state but became fragile in the wet state. On the contrary, the heat‐treated membranes were more flexible in the wet state than in the dry state. This change was explained by the turnaround of inner stress in the systems during the swelling process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008