破片撞击下装甲钢层裂破坏的二维MCA方法模拟

高速破片撞击装甲钢的层裂问题,应考虑侧向稀疏波效应的影响．应用二维MCA方法模拟破片高速撞击装甲钢,以元胞速度场直观地描述这种侧向稀疏效应．模拟得到不同速度撞击下,靶板背面的破坏形态和层裂片形貌、分布及飞散速度,符合实际结果．     

丹皮酚缓释微球的制备及体内外相关性研究

制备具有固体分散结构的丹皮酚缓释微球,并考察其体内外相关性。采用乳化溶剂扩散法制备丹皮酚缓释微球,考察微球的外观、载药量、包封率及体外释放行为。并以丹皮酚原料药为对照,根据大鼠的体内药物动力学试验结果,考察自制微球的体内外相关性。药物在37℃蒸馏水中12 h释放达到85%以上,大鼠体内的药动学实验表明,制得的丹皮酚缓释微球的体外释放累积百分数与体内吸收分数相关系数较好（r=0.977 5）,生物利用度是丹皮酚原料药的136.81%。该方法较适用于难溶性药物制备缓释微球。     

纯棉抗皱织物甲醛含量与测试方法的相关分析

对织物上甲醛含量的测试方法,我国有两项国家标准,分别规定了游离甲醛和释放甲醛的测试方法。本文通过中国国标的两种甲醛测试方法对抗皱处理后的纯棉织物进行测试,得出两种测试方法的相关关系,蒸汽吸收法测试的甲醛含量远远大于水萃取法测试的游离甲醛含量。随着树脂浓度的增大,游离甲醛和释放甲醛的含量会增大;随着烘焙温度的增加,游离甲醛逐渐增加,释放甲醛含量呈下降趋势。     

湖泊富营养化过程中内源性营养盐释放规律的分析

通过采集3种典型营养级别湖泊沉积物,对其营养盐的释放规律进行研究.结果表明：在碱性条件下,富营养化湖泊沉积物中总磷、总氮释放量达到峰值;在中性条件下,富营养化湖泊沉积物中总有机碳释放量最大;在厌氧条件下,富营养化湖泊沉积物中氮、磷、COD的释放量最大.在平行实验条件下3个湖泊中的重度富营养化湖泊的氮、磷、COD的释放量最大.     

液压解卡工具的技术研究与应用

在油田开发中,大负荷解卡是修井作业中常见的工序之一。由于受到地面环境、修井设备的限制,解卡作业的成功率一直比较低。为此,我们引进了液压解卡工具,以液体为动力传递介质,推动井下解卡工具工作,实现大负荷解卡的目的,并且通过6口井的现场实施取得了较好的效果。     

气体释放速率对浅层气藏中气水运移的影响

为了论证在防治浅层气地质工程灾害中预先采取的有控制性排气措施的合理性和必要性,借助非饱和水气两相渗流原理,研究浅层气藏在气体释放路径下的气水运移规律.采用数值方法描述排气井不同释放速率对地下浅层气藏中气水运移的影响.结果表明:气体释放速率对气藏中的气水运移和分布形态有显著影响,释放速率越快,"水锥"效应越明显;实际工程中需结合详勘数据,选取适宜的排气速率,实施控制性放气措施,避免过早发生淹井,导致气井快速失效;在气藏中的浅层气体释放完毕后,砂土中会残留部分以气泡形式存在的气体,施工过程中需引起重视.     

含铁低镍白色金合金镍渗出及抗变色性能

研究Fe元素部分取代镍对白色金合金镍渗出以及抗变色性能影响.指出当Fe等元素取代合金中的部分Ni元素后,由于镍含量降低,合金的镍释放率出现下降,镍降低导致表面镍钝化膜的破坏.当镍质量分数低于2.5%时,合金的镍释放量反而升高.Fe对合金的漂白效果弱于镍,Fe的加入会导致合金抗变色性能降低.均匀化退火热处理对该实验系列金合金材料的抗变色性能影响不大,但可减少合金成分的偏析,有效降低合金的镍渗出量.     

Study on volume ratio and plasticizer screening of free coating membranes composed of ethyl cellulose and chitosan

The aim of this study was to optimize the formula of free blended coating membrane of ethyl cellulose (EC) and chitosan (CS), including their suitable ratio range and the best plasticizer used. The dry films were produced by a casting/solvent evaporation method, with different volume ratio of EC and CS solution plasticized by various plasticizers, respectively. The wet films were prepared by immersing dry films in pH 6.8 phosphate buffer saline (PBS) for 24 h. The promising ratio range of EC/CS was below 20/5 or 20/6 with various plasticizer, which was determined by comparing the viscosity of the blended solutions and the morphology of the blended films. The efficiency of plasticization was evaluated by measuring glass transition temperature (T_g). All the testing plasticizers have good compatibility with EC or CS and dibutyl phthalate (DBP) have the strongest efficiency inducing the lowest T_g (39.9°C) of the film. Mechanical properties were evaluated by the ratio of tensile strength (T) to elastic modulus (E). In the wet state, the films with DBP had the highest T/E value (1.2). The results of leaching of plasticizers also verified that DBP was the most stable plasticizer in the films. The release rates of tetramethylpyrazine phosphate (TMPP) through the pellets coated with the blended films of EC/CS (20 : 6 v/v) plasticized by various plasticizers showed that the more water‐soluble the plasticizer was, the more quickly TMPP dissolved from the coated pellets, which further indicated that the water‐insoluble plasticizers (such as DBP) could be more applicable to keep the sustained or controlled release property of the blended films in wet state. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1932–1939, 2006     

高温快烧釉中彩颜料的研究

为解决日用瓷铅镉溶出问题和提高装饰档次，研制成功１８种高温快烧颜料色基及专用熔剂。经测试，１８种颜料的各项指标全部达到国家标准要求，铅镉溶出量全部为０．０ｍｇ／ｄｍ２．