防腐蚀涂料的性能与选择

介绍并比较几种常用的防腐蚀涂料的品种、组成和性能特点，提出防腐蚀涂料的选择原则。     

Cd-ZSM-5沸石催化剂的制备、表征和芳构化催化性能

采用离子交换、浸渍和混合三种方法制备镉改性ZSM-5沸石催化剂,考察了改性方法和镉含量对催化剂的表面酸性和Cd状态以及芳构化性能的影响。结果表明,加入镉降低了B酸性,Cd~(2+)与沸石结合形成了L_(1612)酸中心,其生成量取决于改性方法和Cd含量,并与芳构化活性提高有直接关系。     

Electrical and optical properties of semi-insulating polycrystalline silicon thin films: the role of microstructure and doping

We have investigated the relationship between microstructure and electrical conductivity in semi-insulating polycrystalline silicon (SIPOS) with oxygen concentrations in the 2–35 at.% range and the effect of doping with boron, phosphorus, arsenic and erbium by ion implantation. SIPOS thin films are mixtures of silicon and silicon oxide phases. The chemical and morphological evolution of these phases upon annealing is emphasized. Electrical conductivity measurements are interpreted in terms of a physical model containing few free parameters related to the material microstructure. A direct extension of this model explains also the conductivity increase in SIPOS doped with elements of the third or the fifth group. In the last part of the paper, data of electroluminescence at 1.54 μm in Er-implanted SIPOS due to intra-4f transitions of the Er³⁺ ion are shown and discussed.     

Synthesis of heterocyclic metal complexes and their evaluation as marine antifoulants

4-Amino-3-thio-1,24-triazolidine (L₁) and 4-amino-5-thio-1,3,4-thiadiazole (L_II) as well as their metal complexes of the general formulae ML_I·2H₂O and ML_IICl (M; Pb(II), Cd(II) and Zn(II)) were prepared. With Sn(II), we obtained Sn(L_I)₂·2H₂O and SnL_IICl, respectively. The structures of the compounds were identified through elemental analysis, and IR and UV spectra measurements, in addition to thermal analysis in case of the metal complexes. The antifouling properties of the compounds were tested by their incorporation into paint formulations which were applied to PVC substrates and tested in water from Alexandria western harbour. When the compounds were added at 17·5% by volume, the coated panels were fouled after 3 months of immersion. The addition of 6·7% by volume of tributyltin oxide to 15·8% of the prepared compounds in one formulation elevated the paint efficiency and prevented fouling for 11 months. Paint containing solely tributyltin oxide at the same concentration was inactive against algae.     

Processing and microstructure of non-oxide ceramic fibres

Research and development efforts on high-temperature, oxidation-resistant fibres have increased over the past decade due to the demand for light-weight, stiff and strong composite materials in aerospace applications. Varieties of ‘high-performance’, continuous, non-oxide fibres with low-density, high tensile strength and tensile modulus have been developed either from organic precursors or via chemical vapour deposition for fabrication of ceramic matrix composites. Fibres derived from polymer precursors (e.g. Nicalon, Tyranno, HPZ) are small in diameter (compared to CVD monofilaments) and are ideally suited for ceramic composites. Processing, microstructural stability and mechanical properties of these newly developed SiC and Si₃N₄ base fibres are briefly reviewed in this paper.     

Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

18Ni（350）马氏体时效钢的磁滞特性

采用双时效处理工艺研究了热轧１８Ｎｉ（３５０）马氏体时效钢的磁滞特性。结果表明，８２０℃·　ｈＡＣ＋（５９－６１０）·。ｈＡＣ＋５１０℃·。ｈＡＣ和８２０℃·　ｈＡＣ＋（６９０－７１０℃）·３ｈＡＣ＋１５０℃·３ｈＡＣ处理具有较高的磁滞性能，在对大量数据进行二元线性回归的基础上得出了１８Ｎｉ（３５０）马氏体时效钢磁滞特性的分段关系式。     

Polymer networks based on α,ω-methacrylate-terminated poly(1,3-dioxolane)

α,ω-Methacrylate-terminated poly(1,3-dioxolane)s (polyDXL) were synthesized by cationic ring-opening polymerization of DXL in the presence of methylene-bis(oxyethylmethacrylate) as transfer agent. If the initiator concentration is small compared with the transfer agent concentration, the molecular weights of the polymers are governed by the ratio of the reacted monomer to the reacted transfer agent. The α,ω-methacrylate-terminated polyDXLs obtained undergo free radical polymerization with formation of polyacetal networks. The properties of the networks as function of the molecular weight of the corresponding prepolymers are reported.     

CF/ABS树脂复合材料制备工艺对导电性能的影响及对屏蔽性能的理论预测

本文研究了使用溶剂法、密炼机和开炼机混炼碳纤维填充ABS树脂复合材料的导电性能,得到了纤维填充量与复合材料电阻率的关系,对其导电机理进行了分析.通过比较,发现纤维长径比是决定复合材料导电性能的重要因素,其它如纤维在基体中的分布也对复合材料导电性能有影响.最后对复合材料的屏蔽性能进行了理论计算.