SiC／Al合金层状复合材料的机械性能及损伤行为

在室温条件下测定了Ａｌ合金以连续层状形式存在于ＳｉＣ陶瓷层间并渗透入ＳｉＣ陶瓷层内、Ａｌ合金浓度呈层状变化高低相间，以及Ａｌ合金和ＳｉＣ陶瓷均匀分布相互渗透三种ＳｉＣ含量相同而结构形式不同的ＳｉＣ／Ａｌ合金复合材料的机械性能；用ＳＥＭ和光学显微镜观察分析了复合材料的断口形貌及裂纹扩展过程。结果表明，在ＳｉＣ陶瓷层间以连续层状形式存在的Ａｌ合金在应力作用下发生较大程度的塑性变形，在裂纹尾部被拉伸和形成桥接，引起能量耗散，减缓裂纹扩展速度，防止裂纹张开，使复合材料的韧性得到明显改善；ＳｉＣ／Ａｌ合金陶瓷─金属层状复合材料的损伤形式主要是ＳｉＣ陶瓷层开裂、金属层桥接和裂纹偏转。     

Mechanical behavior of 30–50 nm thick aluminum films under uniaxial tension

We present uniaxial tensile test results for 30–50 nm thick freestanding aluminum films. Young’s modulus and ductility were found to decrease monotonically with grain size. Reverse Hall–Petch behavior was observed with no appreciable room temperature creep. Non-linear elasticity with small irreversible deformation was observed for 50 nm thick specimens.     

HA型粘结剂性能评判的研究

冷固结球团直接还原工艺成功的关键因素之一是成型粘结剂的选用。粘结剂性能评判 ,传统的方法是通过考查球团矿的机械强度来说明粘结剂性能的优劣 ,步骤繁锁。经过试验研究 ,本文提出了用粘度大小来评判粘结剂性能的直接方法并从理论上进行了论证。对于 HA型复合粘结剂 ,在六速旋转粘度计上测量 ,50 g复合粘结剂的粘度若大于或等于 6.5× 1 0 -3 Pa·s,表示粘结剂性能较好 ,能满足铁精矿冷固球团直接还原工艺的要求 ;若小于或等于 3.0× 1 0 -3 Pa· s,则表示该粘结剂性能较差。     

BaFe12O19/SiO2-B2O3微晶玻璃陶瓷的制备和微波性能

采用柠檬酸sol-gel工艺合成了BaFe12O19/SiO2-B2O3微晶玻璃陶瓷，研究了SiO2-B2O3玻璃的含量，Ba/Fe原子比和热处理温度对体系析出晶相的影响，以及介电常数和磁异率在1MHz-6GHz频率范围的变化规律，结果表明，休系中SiO2-B2O3玻璃的含量和Ba/Fe比越高，BaF312O19相的析出越困难，前驱体合适的热处理温度为1000℃，介电常数和磁导率基本上随测试频率的增而加下降；介电损耗的最大值为0．43，磁损耗较小。     

Si基膜片型气敏传感器微结构单元的热学性能

微结构气敏传感器由于其微型化、低功耗、易阵列化和易批量生产等优点而受到国内外研究者的广泛关注。利用微机电系统（MEMS）加工技术，制备Si基膜片型微结构单元，并分析其热学性能。这种单元工作区温度为-300℃时，加热功率约75mW；并且膜片工作区的热质量很小，温度可以于毫秒量级的时间内，在室温和450℃之间调制。利用这种微结构单元，可以在温度调制方式下，研究气敏薄膜的电学特性和敏感机理。     

功能化的介孔分子筛碱催化性能的研究

以苯甲醛与氰乙酸乙酯的Knoevenagel缩合为模型反应，研究了用γ－氨丙基三乙氧基硅烷或γ－乙二胺丙基三甲氧基硅烷功能化的纯硅介也分子筛HMS（Hexagonal mesoporous silica）的碱催化性能。结果表明，除个别碱基负载量高的样品外，功能化样品对反应显示很高的催化活性，反应的初期活性不仅取决于催化剂上活性中心的密度，而且与载体的孔道结构有关。大孔径载体有利于反应物、产物的扩散，故在高负载量时，大孔径样品比小孔样品有更高的活性。此外，还考察了反应温度、溶剂、反应物配比和催化剂用量等条件的影响以及催化剂的重复使用情况。结果表明，反应可在低于100℃的温和条件下进行，有明显的溶剂效应，反应物配比和催化剂用量存在一最佳值；随使用次数的增加，催化剂逐渐中毒而失活。     

Effects of hydrolysis on the physical properties of short glass-fibre reinforced poly(ethylene terephthalate)

The mechanical fracture strength and toughness of short-fibre composites, injection moulded from compounds of poly(ethylene terephthalate) (PET) containing 10 and 30% (by weight) (w/o) glass, have been investigated and the dependence upon matrix hydrolytic stability determined. Mouldings have been characterised by several physical techniques to evaluate molecular weight, degradation rates, crystallinity and morphology, whilst time-dependent gravimetric data were derived to quantify sorption kinetics and allow comparisons with theoretical reaction rates to be made. During melt processing, PET is hydrolysed extremely rapidly by traces of moisture (<0.02w/o). yet the inherent strength of moulded composites declines significantly only below an apparently critical molecular weight. However, on long-term humid ageing in hot water, impact behaviour especially is rendered more complex by simultaneous crystallisation, molecular reorder and losses of interfacial bond strength.     

Measurement of Gibbs energies of formation of CoF2 and MnF2 using a new composite dispersed solid electrolyte

Gibbs energies of formation of CoF₂ and MnF₂ have been measured in the temperature range from 700 to 1100 K using Al₂O₃-dispersed CaF₂ solid electrolyte and Ni+NiF₂ as the reference electrode. The dispersed solid electrolyte has higher conductivity than pure CaF₂ thus permitting accurate measurements at lower temperatures. However, to prevent reaction between Al₂O₃ in the solid electrolyte and NiF₂ (or CoF₂) at the electrode, the dispersed solid electrolyte was coated with pure CaF₂, thus creating a composite structure. The free energies of formation of CoF₂ and MnF₂ are (± 1700) J mol⁻¹; {fx37-1} The third law analysis gives the enthalpy of formation of solid CoF₂ as ΔH° (298·15 K) = −672·69 (± 0·1) kJ mol⁻¹, which compares with a value of −671·5 (± 4) kJ mol⁻¹ given in Janaf tables. For solid MnF₂, ΔH°(298·15 K) = − 854·97 (± 0·13) kJ mol⁻¹, which is significantly different from a value of −803·3 kJ mol⁻¹ given in the compilation by Barinet al.     

啤酒标签用铝箔力学性能研究

分析研究了连续铸轧坯料的合金成分，冶金组织和热处理工艺对啤酒标用铝箔力学性能的影响，选定成形性优良的合金系列，并优化铸轧工艺和热处理工艺是提高铝箔力学性能的关键。