基于环形微热板的ZnO微气体传感器设计

提出一种新型的设有环形结构微热板的硅基ZnO微气体传感器。利用ANSYS软件,将环形电极结构与传统的蛇形结构进行温度分布的模拟仿真,发现该结构能供给传感器更高的温度且中心温度分布均匀,进而解决了现有传感器功耗大的缺点。通过对RF磁控溅射ZnO薄膜的工艺摸索,得出了适宜作气敏薄膜的制备参数。该传感器在250℃下对（200-1000）×10-6CH4气体有很好的响应。     

一次多级离心泵运行故障处理及分析

简要介绍了实际生产中多级离心泵存在的问题,并分析了故障原因和处理措施。     

双金属氰化物催化剂的研究进展

综述了近年来双金属氰化物（DMC）催化剂的研究进展，指出DMC催化剂是一类用于环氧化物的高效催化剂，与传统的环氧化物催化剂相比，其制得的聚醚多元醇具有分子量高、不饱和度低、分子量分布窄、平均官能度高等优点。但该催化剂在应用过程中仍存在一些缺点。针对这些缺点，国内外的高校、企业已进行了大量的改性研究工作。     

海洋非黏结柔性管道接头密封结构分析

介绍海洋非黏结柔性管道接头的常见密封结构,用Abaqus对接头的密封特性进行数值分析,研究密封圈的密封性能对不同密封结构参数的灵敏度,得到密封结构参数变化对接头密封结构的密封性能和力学性能影响的一般规律.结果表明密封结构的主要设计参数为密封圈的锥角和曲率半径以及加载位移等.     

One‐step synthesis and ring‐opening polymerization of novel macrocyclic(arylene multisulfide) oligomers

A series of macrocyclic(arylene multisulfide) oligomers were synthesized under high dilution conditions by reacting diphenyl ether/diphenyl/diphenyl disulfide/diphenyl methane with dichloro disulfide in the presence of a trace amount of iron powder by a one‐step reaction. From MALDI‐TOF mass spectra, it was established that the repeating units of the cyclization ranged from two to seven and the unit of macrocyclic(arylene multisulfide) oligomers had one to seven sulfur atoms. The macrocyclic oligomers readily underwent ring‐opening polymerization in the melt, resulting in linear, high molecular weight polymultisulfides. DSC thermograms demonstrated that the four polymultisulfides, derived from the macrocyclic(arylene multisulfide) oligomers, are amorphous in nature. The macrocyclic(arylene multisulfide) oligomers and polymers were analyzed by MALDI‐TOF‐MS, IR, HPLC, NMR, DSC, and TGA methods. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 735–741, 2004     

楔形环管片纵向接头对施工荷载力学响应研究

楔形环管片是盾构隧道曲线段的重要组成部分。以珠海-澳门轻轨某急弯隧道为例,利用ANSYS有限元软件计算了楔形环管片在不同管片幅宽、楔形量、隧道曲率半径、千斤顶压力等条件下管片纵向接头的受力情况,重点分析了管片环间接头的最大正负弯矩。研究结果表明:随着盾构隧道曲线半径减小,正负最大弯矩均增大,不同隧道转弯半径下,管片最大正负弯矩均随接头抗弯刚度的增大而增大;不论正负弯矩,均有管片幅宽越小最大弯矩越大的现象。不同管片幅宽下,管片最大正负弯矩均随接头抗弯刚度的增大而增大;曲线半径为150 m时,最大正弯矩基本随着千斤顶压力呈线性增大的趋势,最大约为1 180 k N·m。研究结果对今后的急弯盾构隧道管片设计有一定的指导意义。     

大型渣油气化炉激冷室热质传递过程模拟

对现行８．５３ＭＰａ德士古渣油气化炉激冷室中热质传递过程进行了分析、研究，从数学模型着手，进行模拟计算，模拟结果与工业数据吻合良好。通过模拟揭示了激冷过程本质特征，探讨了现行激冷环损坏的主要原因。     

Cationic copolymerization behavior of a bicyclic orthoester having hydroxy group with glycidyl phenyl ether and volume change on their copolymerization

This article describes cationic ring‐opening copolymerization of a bicyclic orthoester having hydroxy group (BOE‐OH) and glycidyl phenyl ether (GPE), and the volume shrinkage behavior during the copolymerization. THF soluble polyethers [poly(BOE‐OH‐co‐GPE)] were obtained by the copolymerizations at 80–180°C, while crosslinked poly(BOE‐OH‐co‐GPE) was obtained by the copolymerizations at 220–250°C. This crosslinking reaction may originate from the dehydration of methylol groups in the side chain of poly(BOE‐OH‐co‐GPE). The volume shrinkage during the cationic copolymerization reduced as the increase of the BOE‐OH feed ratio. By contrast, the volume shrinkage on the crosslinking polymerization was almost independent on the BOE‐OH feed ratio. Poly(BOE‐OH‐co‐GPE)s with higher BOE‐OH composition showed lower thermal weight loss temperature owing to the release of H₂O by dehydration of methylol groups. The BOE‐OH component in the THF soluble poly(BOE‐OH‐co‐GPE)s lowered the glass transition temperature (T_g), while that in the crosslinked poly(BOE‐OH‐co‐GPE) increased the T_g probably because of the higher crosslinking density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1356–1361, 2006     

3-取代苯基-5-羟基-5-三氟甲基异噁唑啉的合成

3 取代苯基 5 羟基 5 三氟甲基异口恶唑啉是合成具有异口恶唑结构的原卟啉原氧化酶抑制剂类除草剂的重要中间体。通过以下途径制得4个具有不同取代基的异口恶唑啉中间体:首先,在回流状态,n(甲醇钠)∶n(取代苯乙酮)=2∶1的甲醇钠存在下,取代苯乙酮与三氟乙酸乙酯缩合得到取代苯基 4,4,4 三氟 1,3 丁二酮;后者可在室温下,于二氯甲烷溶剂中,用氯化硫酰氯化,在侧链上引入氯原子;最后,以乙酸作溶剂,回流下,具有不同取代基的苯基 1,3 丁二酮与盐酸羟胺闭环得到产物。反应总收率大于95%。产品结构经质谱、核磁共振氢谱、碳谱确认正确。     

A 60‐GHz on‐chip slot‐array antenna in integrated‐passive‐device technology for antenna‐in‐package applications

A new millimeter‐wave antenna structure on a low‐cost, production platform integrated passive device technology is presented. The antenna consists of a 2‐by‐1 array of slot antennas at 60 GHz. An in‐house developed on‐chip antenna measurement setup was used to characterize the fabricated antenna. The measurement results show an antenna gain of more than 5 dBi with a return loss of 18 dB at 60 GHz. The better‐than‐10‐dB impedance bandwidth of the antenna covers the 60‐GHz unlicensed band from 57 to 64 GHz. The 3‐dB beamwidths of the antenna are 105° and 76° at E‐plane and H‐plane at 60 GHz, respectively. The size of the die of the antenna is 2 mm × 4.5 mm. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:155–160, 2014.