气化炉锥底砖、激冷环与下降筒的损毁与解决对策

针对国产化大氮肥水煤浆气化炉中锥底砖、激冷环和下降筒使用过程中出现的问题,分析了损毁原因,分别从技术改进、工艺操作和设备管理等方面提出了相应的解决对策,可以不同程度地延长锥底砖、激冷环、下降筒的寿命。     

GRM-2SD120棉线缠绕机

介绍了GRM－2SD120棉线缠绕机的结构原理，重点介绍了该机的锭子部分，口型部分，锭子盘，中胶部分，传动原理，电气原理及主要技术参数。     

一次多级离心泵运行故障处理及分析

简要介绍了实际生产中多级离心泵存在的问题,并分析了故障原因和处理措施。     

One‐step synthesis and ring‐opening polymerization of novel macrocyclic(arylene multisulfide) oligomers

A series of macrocyclic(arylene multisulfide) oligomers were synthesized under high dilution conditions by reacting diphenyl ether/diphenyl/diphenyl disulfide/diphenyl methane with dichloro disulfide in the presence of a trace amount of iron powder by a one‐step reaction. From MALDI‐TOF mass spectra, it was established that the repeating units of the cyclization ranged from two to seven and the unit of macrocyclic(arylene multisulfide) oligomers had one to seven sulfur atoms. The macrocyclic oligomers readily underwent ring‐opening polymerization in the melt, resulting in linear, high molecular weight polymultisulfides. DSC thermograms demonstrated that the four polymultisulfides, derived from the macrocyclic(arylene multisulfide) oligomers, are amorphous in nature. The macrocyclic(arylene multisulfide) oligomers and polymers were analyzed by MALDI‐TOF‐MS, IR, HPLC, NMR, DSC, and TGA methods. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 735–741, 2004     

二甲基亚砜一步法碳纤维用聚丙烯腈原丝生产工艺

叙述了二甲基亚砜一步法（高转化）高强碳纤维用聚丙烯腈原丝生产的工艺流程。着重讨论了聚合、纺丝的工艺控制。以及工艺控制对聚丙烯腈原丝和最终碳纤维性能的影响。按此工艺生产的聚丙烯腈原丝的质量完全符合高强碳纤维生产的需要。     

闪蒸法聚乙烯无纺布的研究进展

介绍了无纺布的发展历程以及我国无纺布的现状，着重讨论了开展闪蒸法聚乙烯纺粘型无纺布研究的意义、方法、生产工艺。     

大型渣油气化炉激冷室热质传递过程模拟

对现行８．５３ＭＰａ德士古渣油气化炉激冷室中热质传递过程进行了分析、研究，从数学模型着手，进行模拟计算，模拟结果与工业数据吻合良好。通过模拟揭示了激冷过程本质特征，探讨了现行激冷环损坏的主要原因。     

卧式一步法丙纶高强丝生产工艺研究

在意大利ＦＡＲＥ公司卧式一步法丙纶高强丝设备上，研究了聚丙烯熔融指数与丙纶高强丝强度的关系。探讨了纺丝温度、冷却条件、单丝纤度、拉伸倍数等主要工艺条件对丙纶高强丝强度的影响。     

Cationic copolymerization behavior of a bicyclic orthoester having hydroxy group with glycidyl phenyl ether and volume change on their copolymerization

This article describes cationic ring‐opening copolymerization of a bicyclic orthoester having hydroxy group (BOE‐OH) and glycidyl phenyl ether (GPE), and the volume shrinkage behavior during the copolymerization. THF soluble polyethers [poly(BOE‐OH‐co‐GPE)] were obtained by the copolymerizations at 80–180°C, while crosslinked poly(BOE‐OH‐co‐GPE) was obtained by the copolymerizations at 220–250°C. This crosslinking reaction may originate from the dehydration of methylol groups in the side chain of poly(BOE‐OH‐co‐GPE). The volume shrinkage during the cationic copolymerization reduced as the increase of the BOE‐OH feed ratio. By contrast, the volume shrinkage on the crosslinking polymerization was almost independent on the BOE‐OH feed ratio. Poly(BOE‐OH‐co‐GPE)s with higher BOE‐OH composition showed lower thermal weight loss temperature owing to the release of H₂O by dehydration of methylol groups. The BOE‐OH component in the THF soluble poly(BOE‐OH‐co‐GPE)s lowered the glass transition temperature (T_g), while that in the crosslinked poly(BOE‐OH‐co‐GPE) increased the T_g probably because of the higher crosslinking density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1356–1361, 2006     

有色双细全牵伸丝的研制开发

从生产实践出发,探讨了33dtex/24f双细全牵伸丝（FDY）丝的生产工艺。在选择工艺参数时应考虑色母粒对纺丝生产的影响。合理地选择纺丝温度、喷丝板孔径、拉伸速度、牵伸倍数可稳定地生产性能良好的FDY丝。