一次多级离心泵运行故障处理及分析

简要介绍了实际生产中多级离心泵存在的问题,并分析了故障原因和处理措施。     

双金属氰化物催化剂的研究进展

综述了近年来双金属氰化物（DMC）催化剂的研究进展，指出DMC催化剂是一类用于环氧化物的高效催化剂，与传统的环氧化物催化剂相比，其制得的聚醚多元醇具有分子量高、不饱和度低、分子量分布窄、平均官能度高等优点。但该催化剂在应用过程中仍存在一些缺点。针对这些缺点，国内外的高校、企业已进行了大量的改性研究工作。     

海洋非黏结柔性管道接头密封结构分析

介绍海洋非黏结柔性管道接头的常见密封结构,用Abaqus对接头的密封特性进行数值分析,研究密封圈的密封性能对不同密封结构参数的灵敏度,得到密封结构参数变化对接头密封结构的密封性能和力学性能影响的一般规律.结果表明密封结构的主要设计参数为密封圈的锥角和曲率半径以及加载位移等.     

Effect of alkali and ultraviolet (UV) radiation pretreatment on physical and mechanical properties of 1,6‐hexanediol diacrylate–grafted jute yarn by UV radiation

To improve the physicomechanical properties of jute yarn, grafting with 1,6‐hexanediol diacrylate (HDDA) monomer was performed by a UV radiation technique. A series of HDDA solutions of various concentrations in methanol were prepared. A small quantity of photoinitiator (Darocur‐1664) was also added to HDDA solutions. To optimize the conditions for grafting, the effects of monomer concentration, soaking time, and radiation doses were studied by varying the number of soaking times along with variation of monomer concentrations and UV radiation intensities. The extent of polymer loading and the mechanical properties like tensile strength (TS), elongation at break (Eb), and tensile modulus of both treated and untreated jute were investigated. The highest tensile strength, polymer loading, and modulus were achieved with 5% HDDA concentration, 5 min soaking time, and the 4th pass of UV radiation. This set of conditions was selected as optimum and produced enhanced tensile strength (67%), modulus (108%), and polymer loading (11%) over those of virgin fiber. To further improve the mechanical properties the jute yarns were pretreated with alkali (5% NaOH) solution and after that the alkali‐treated yarn were treated under UV radiation of various intensities. The pretreated samples were grafted with optimized monomer concentration (5% HDDA). Increased properties of alkali + UV‐pretreated and grafted samples such as polymer loading (12%), tensile strength (103%), elongation at break (46%), and modulus (114%) were achieved over those of virgin jute yarn. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 18–24, 2004     

One‐step synthesis and ring‐opening polymerization of novel macrocyclic(arylene multisulfide) oligomers

A series of macrocyclic(arylene multisulfide) oligomers were synthesized under high dilution conditions by reacting diphenyl ether/diphenyl/diphenyl disulfide/diphenyl methane with dichloro disulfide in the presence of a trace amount of iron powder by a one‐step reaction. From MALDI‐TOF mass spectra, it was established that the repeating units of the cyclization ranged from two to seven and the unit of macrocyclic(arylene multisulfide) oligomers had one to seven sulfur atoms. The macrocyclic oligomers readily underwent ring‐opening polymerization in the melt, resulting in linear, high molecular weight polymultisulfides. DSC thermograms demonstrated that the four polymultisulfides, derived from the macrocyclic(arylene multisulfide) oligomers, are amorphous in nature. The macrocyclic(arylene multisulfide) oligomers and polymers were analyzed by MALDI‐TOF‐MS, IR, HPLC, NMR, DSC, and TGA methods. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 735–741, 2004     

二甲基亚砜一步法碳纤维用聚丙烯腈原丝生产工艺

叙述了二甲基亚砜一步法（高转化）高强碳纤维用聚丙烯腈原丝生产的工艺流程。着重讨论了聚合、纺丝的工艺控制。以及工艺控制对聚丙烯腈原丝和最终碳纤维性能的影响。按此工艺生产的聚丙烯腈原丝的质量完全符合高强碳纤维生产的需要。     

闪蒸法聚乙烯无纺布的研究进展

介绍了无纺布的发展历程以及我国无纺布的现状，着重讨论了开展闪蒸法聚乙烯纺粘型无纺布研究的意义、方法、生产工艺。     

楔形环管片纵向接头对施工荷载力学响应研究

楔形环管片是盾构隧道曲线段的重要组成部分。以珠海-澳门轻轨某急弯隧道为例,利用ANSYS有限元软件计算了楔形环管片在不同管片幅宽、楔形量、隧道曲率半径、千斤顶压力等条件下管片纵向接头的受力情况,重点分析了管片环间接头的最大正负弯矩。研究结果表明:随着盾构隧道曲线半径减小,正负最大弯矩均增大,不同隧道转弯半径下,管片最大正负弯矩均随接头抗弯刚度的增大而增大;不论正负弯矩,均有管片幅宽越小最大弯矩越大的现象。不同管片幅宽下,管片最大正负弯矩均随接头抗弯刚度的增大而增大;曲线半径为150 m时,最大正弯矩基本随着千斤顶压力呈线性增大的趋势,最大约为1 180 k N·m。研究结果对今后的急弯盾构隧道管片设计有一定的指导意义。     

大型渣油气化炉激冷室热质传递过程模拟

对现行８．５３ＭＰａ德士古渣油气化炉激冷室中热质传递过程进行了分析、研究，从数学模型着手，进行模拟计算，模拟结果与工业数据吻合良好。通过模拟揭示了激冷过程本质特征，探讨了现行激冷环损坏的主要原因。     

卧式一步法丙纶高强丝生产工艺研究

在意大利ＦＡＲＥ公司卧式一步法丙纶高强丝设备上，研究了聚丙烯熔融指数与丙纶高强丝强度的关系。探讨了纺丝温度、冷却条件、单丝纤度、拉伸倍数等主要工艺条件对丙纶高强丝强度的影响。