真空制盐蒸发结晶器的设计与实践

真空蒸发制盐外热式强制逆循环轴向出料蒸发结晶器，经多个厂家生产应用实践证明是成功的，具有生命力的。这种新型结构，作为一项新技术新设备应加强研究，总结提高，推广应用。不断完善。文章从流体力学、结晶机理角度要求，到具体工程设计参数和材质选用。论述了该罐的特点。     

黄河下游河道萎缩致灾机理探讨

本文基于水力学原理，结合实体模型试验及原型实测资料分析，探讨了黄河下游河道萎缩的概念、致灾效应和致灾机理。分析表明，河道萎缩是造床过程中河道排洪输沙功能衰退的一种演变现象，其致灾效应是使洪水涨率增大，同流量下洪水水位不断抬升。致灾的现象主要表现在畸型河势增加、工程险情增多、直接造成工程损失及滩区经济损失等。试验研究揭示，主河槽宽度缩窄造成洪水水位涨幅增大，河底平均高程抬升和过水断面面积减小造成洪水水位起涨的基准面抬升是河道萎缩致灾的主要原因。河道萎缩致灾效应的大小与萎缩模式有关，其中以“集中淤槽”模式所形成的致灾效应尤为明显。     

Reaction scheme and kinetic modelling for the MTO process over a SAPO-18 catalyst

A kinetic model for simulation of the MTO process over SAPO-18 catalyst in a wide range of operating conditions has been proposed. The kinetic model predicts the experimental evolution of reaction products with time on stream, which follows three consecutive periods: initiation (where olefin production increases), a period of maximum olefin production and a period in which this production decreases. The kinetic scheme takes into account these three steps that evolve with time on stream: formation of active intermediate compounds, an step where olefins are formed by reaction of oxygenates (methanol/DME) with these intermediates and deactivation of intermediates by degradation to coke. The presence of water in the reaction medium attenuates the reaction rate of these steps. Discrimination of kinetic equations and calculation of the parameters of best fit have been carried out by solving the mass conservation equations of the individual components of the kinetic scheme together with the kinetic equation for deactivation and taking into account the effect of water on the kinetics of each step.     

论剪切质量的提高

通过对飞剪剪切长度，精度，剪刃间隙和压板机构等参数的优化，来提高钢板的剪切质量。     

论我国大学不良竞争的形成及控制

大学在办学资源、办学过程、办学质量、办学形象的竞争中出现大量的不良倾向。大学的不良竞争是由于政府主导资源配置、资源和制度供给不足、大学系统重构等因素导致。必须通过控制主体、控制手段的转变和控制对象的发展形成新的控制机制，以保证大学竞争的秩序化和规范化。     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Formation of composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system

The formation of aluminum matrix composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system was investigated. The thermal analysis results show that the reactions are spontaneous and exothermic. The Gibbs free energy of α-Al2O3 is the lowest among all the combustion products, followed by TiB2 and Al3Ti. It is noted that when the B2O3/TiO2 mole ratio is below 1, the reaction products are composed of particle-like α-Al2O3, TiB2 and rod-like Al3Ti. The α-Al2O3 crystallites, resulting from the reaction between A1 and TiO2 or B2O3, are segregated at the grain boundaries due to a lower wettability with the matrix. SEM micrographs show that rod-like Al3Ti phase distributes uniformly in the matrix. When the BEO3/TiO2 mole ratio is around 1, the Al3Ti phase almost disappears in the composites, and the distribution of α-Al2O3 particulates is improved evidently.     

Ring‐opening polymerization of D,L‐lactide by rare earth 2,6‐dimethylaryloxide

Ring‐opening polymerization of D,L ‐lactide (LA) has been successfully carried out by using rare earth 2,6‐dimethylaryloxide (Ln(ODMP)₃) as single component catalyst or initiator for the first time. The effects of different rare earth elements, solvents, monomers and catalyst concentration as well as polymerization temperature and time on the polymerization were investigated. The results show that La(ODMP)₃ exhibits higher activity to prepare poly(D,L ‐lactide) (PLA) with a viscosity molecular weight of 4.5 × 10⁴ g mol^?1 and the conversion of 97 % at 100 °C in 45 min. The catalytic activity of Ln(ODMP)₃ has following sequence: La > Nd > Sm > Gd > Er > Y. A kinetic study has indicated that the polymerization is first order with respect to both monomer and catalyst concentration. The apparent activation energy of the polymerization of LA with La(ODMP)₃ is 69.6 kJ mol^?1. The analyses of polymer ends indicate that the LA polymerization proceeds according to ‘coordination–insertion’ mechanism with selective cleavage of the acyl–oxygen bond of the monomer. Copyright © 2004 Society of Chemical Industry     

Hydrothermal Reaction Mechanism and Pathway for the Formation of K2Ti6O13 Nanowires

Calculations and detailed first principle and thermodynamic analyses have been performed to understand the formation mechanism of K₂Ti₆O₁₃ nanowires (NWs) by a hydrothermal reaction between bulk Na₂Ti₃O₇ crystals and a KOH solution. It is found that direct ion exchange between K⁺ and Na⁺ plus H⁺ interactions with [TiO₆] octahedra in Na₂Ti₃O₇ promote the formation of an intermediate H₂K₂Ti₆O₁₄ phase. The large lattice mismatch between this intermediate phase and the bulk Na₂Ti₃O₇ structure, and the large energy reduction associated with the formation of this intermediate phase, drive the splitting of the bulk crystal into H₂K₂Ti₆O₁₄ NWs. However, these NWs are not stable because of large [TiO₆] octahedra distortion and are subject to a dehydration process, which results in uniform K₂Ti₆O₁₃ NWs with narrowly distributed diameters of around 10 nm.     

An Agent Interaction Based Method for Nonlinear Process Plan Scheduling

This article puts forward a scheduling method for nonlinear process plan shop floor.Task allocation and load bal- ance are realized by bidding mechanism.Though the agent interaction process,the execution of tasks is determined and the coherence of manufacturing decision is verified.The employment of heuristic index can help to optimize the system performance.