A study of suppression of vapor explosions by adding inversely soluble polymers

The mechanism of the suppression of vapor explosions by adding inversely soluble polymers in water is studied. Vapor explosion experiments and quench experiment are conducted using a silver test piece. Polymetric solution (polyethylene oxide), of concentrations from 0 to 500 wppm, whose normalized viscosity (by water) varies from 1.00 to 2.00, is used. No vapor explosion is observed in the aqueous polymer solution at a concentration higher than 200 wppm. Quench experiments using the silver test piece submerged in the polymer solution and water are performed in order to examine the stability of film boiling. The suppression of the vapor film collapse is attributed to the precipitation of polyethylene as a gel around the vapor film. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(4): 297–306, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10037     

烷基化原料预加氢工艺应用分析

由于来自催化裂化装置的烷基化原料中所含有的丁二烯在烷基化反应中可生成重质油,使产品干点上升,辛烷值下降,并使酸耗增加.针对这种状况,齐鲁石化公司研究院和胜利炼油厂联合开发了QSH-01烷基化原料预加氢催化剂及其相应的工艺技术,来脱除原料中丁二烯.笔者对该工艺技术及其应用作了阐述,并对该技术的应用前景作出分析.     

含微量元素铜焊锡丝的研制

在６０／４０的锡铅焊料中加入０．２％左右的铜，凝固后具有均匀细小的共晶组织，其熔点为１８３℃，焊点强度和扩展率均高于未加铜的６０／４０锡铅焊料，并且含铜的锡铅焊料在焊接时，对铜烙铁头和微细铜线了小的熔蚀性。     

丙烯酸高碳醇酯的合成

介绍了降凝剂中间体丙烯酸高碳醇酯的合成和产品分离提纯方法。考察了合成条件对酯化反应的影响，结果表明，在原料丙烯酸与十八醇摩尔比1．2：1，阻聚剂对苯二酚用量占原料总量1．5％，催化剂对甲苯磺酸用量占原料总量1．5％，反应温度80-86℃，回流反应时间6h条件下，酯化率最高达89％。产品分离提纯方法与传统分离方法比较，所需分离时间短，洗涤用水量少，而产品收率远高于传统分离方法，达95％以上。     

一种基于小波变换的OTDR事件分析算法的研究

简单分析了用 OTDR卡进行光纤检测的原理 ,根据小波分析检测信号突变点的理论 ,提出了运用小波分析对光纤断点及反射事件准确定位的方法。理论分析和实例计算表明 ,这种方法对 OTDR曲线中反射事件尤其是断点的定位非常准确 ,是一种行之有效的方法     

Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

An introduction to Wu's method for mechanical theorem proving in geometry

Wu's algebraic method for mechanically proving geometry theorems is presented at a level as elementary as possible with sufficient examples for further understanding the complete method.The work reported here was supported by NSF Grant DCR-8503498.     

论校园文化和德育目标的一致性

中系统介绍了校园化和德育目标的关系，并找准两之间的结合点，通过分析两的一致性和辩证统一关系，达到育人目的。     

The Problem of Estimating the Uncertainty of the Fixed Point Temperature Due to the Presence of Impurities

The main problems in estimating the uncertainty due to the presence of impurities in the material: the absence in the documents of a unique definition of the quantity being measured – the fixed point temperature, the lack of agreed methods of realizing the fixed points and the insufficient justification of the equations used for the estimate, are analyzed. The results of a measurement of the melting point of gallium are presented, which differ in the conditions in which they were realized – with one and two liquid-solid interfaces and different solidification conditions, are presented. The reasons for the considerable difference between the values of the temperatures obtained in these experiments are discussed.     

铜铟铋硫对Sn-Ag基无铅焊料性能的影响

研究了Cu、In、Bi、S元素对Sn-Ag基无铅焊料熔点和铺展性的影响。结果表明:Sn-Ag-Cu三元合金成分为95.5%Sn3.5%Ag1%Cu时具有较低熔点(215℃)和好的铺展性;加入适量的In可降低Sn-Ag合金的熔点和改善铺展性能;随w(Bi)的增加Sn-Ag-Bi三元合金的熔点降低、铺展性变好;Sn-Ag合金的熔点随w(S)的增加而升高,加入少量S能改善Sn-Ag合金的铺展性。