可与氟树脂基板相匹敌的热可塑性树脂基板材料

概述了可以与氟树脂基板相匹敌的低介质特性的热可塑性树脂基板材料的开发和应用。     

Anhydrous esterification of myristic acid with propylene: Ion exchange resin and acid-treated clay as catalysts

Anhydrous esterification of myristic acid with propylene was carried out in the temperature range of 110–145°C and pressure from 190–195 psig in the presence of Amberlyst-15 (cation exchange resin) and Filtrol-24 (acid-treated clay) as catalysts. The product ester, isopropyl myristate finds use in cosmetic and topical medicinal preparations where good absorption through the skin is desired. Filtrol-24 is the catalyst of choice, and the recommended operating temperature is 130°C with a pressure of 190 psig.     

The effects of glycol methacrylate as a dehydrating agent on the dimensional changes of liver tissue

The dimensional changes of liver sections during the course of processing with glycol methacrylate (GMA) or with ethanol are described. Tissue processing with ethanol served as a control. During prolonged processing steps (24 h each), linear shrinkage of tissue specimens dehydrated with GMA at room temperature was 13.2%. Subsequent infiltration with GMA resulted in trivial swelling, and polymerization in slight shrinkage (2.3%). In comparison, processing with cold GMA resulted in shrinkage during dehydration (about 10.8%), a slight swelling in pure GMA, followed by shrinkage during polymerization (2.2%). Short routine processing schedules resulted in similar shrinkage/swelling patterns, although precise values differed slightly. In all experiments, ethanolic dehydration resulted in smaller dimensional tissue changes than did GMA dehydration. The dimensional changes of tissue sections during stretching on water, mounting and drying compensated for the major part of the shrinkage manifested during processing.     

某炼油厂一级浮床除盐系统阳床工艺特性及调整试验

论述了某厂一级除盐系统阳床工艺特性及调整试验过程，对存在问题进行分析并改进，得到了实际运行最佳方式和参数，取得良好效果。     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

桐油改性酚醛树脂的结构及固化过程的研究

通过桐油与苯酚在酸性催化剂存在下反应，然后再在碱性催化剂存在与甲醛反应制得了一种热固性桐油改性酚醛树脂。利用红外光谱，差示扫描量热法分析技术对改性树脂的结构及固化反应过程进行了研究。     

新型环氧树脂绝缘浸渍胶（WSK）在微特电机上的应用

介绍了新型环氧树脂少溶剂快干绝缘浸渍胶的性能试验数据及基在微特电机上的应用及注意事项。     

Use of inverse gas chromatography to quantify interactions in amine cured epoxy resins

Flory–Huggins interaction parameters, λ, were determined for a series of probes in an amine cured epoxy resin matrix (433–493 K) and its precursors (324–363 K) by inverse gas chromatography (IGC). Hildebrand–Scatchard theory was combined with Flory–Huggins theory in order to estimate infinte dilution solubility parameters (δ₂) for the matrix and its precursors at 298 K. It was shown that the value of the solubility parameter for the cured resin matrix lies between those of its precursors. Compared to the majority of published work, an unusual aspect of this application of IGC is that solubility parameters have been determined when the stationery phases are (i) small molecules and (ii) a highly crosslinked polymer. Moreover, all possible attempts have been made to ensure equilibrium conditions between probe and stationary phase, and compensation for asymmetry of peak profile has been applied in determining δ₂. The solubility parameters estimated by IGC are in good agreement with those calculated by other methods.     

On the curing of a vinylester-urethane hybrid resin

Curing kinetics of a vinylester-urethane hybrid (VEUH) resin consisting of vinylester resin (VE) diluted in styrene and novolac type polyisocyanate (NPI) have been studied by differential scanning calorimetry (DSC). As VEUH is crosslinked via free radical polymerisation between the vinyl functions of styrene and VE, and polyaddition reaction between the secondary -OH groups of VE and -NCO of NPI, it was necessary to study these reactions separately. This was achieved by studying the curing with and without incorporating the NPI. The curing reaction was monitored by measuring the heat of reaction under isothermal and dynamic temperature conditions. Models describing the curing were developed, which are in good agreement with the experiments. A comparison between the curing of the VEUH and the VE resin without NPI leads to the conclusion that the curing of the VEUH as accessed by DSC is dominated by the radical polymerisation of styrene with VE although the two reactions are not time separated.