环缝错边容器的有限元分析与容限探讨

采用有限元方法对 1台封头与筒体具有较大错边量的容器进行了应力分析 ,得到了错边区域的应力分布状况 ,并对其进行应力强度评定。结果表明 ,该容器错边部位的应力是满足应力分析准则的。通过对存在不同错边量的容器进行应力分析 ,探讨了容器的错边容限 ,对含有错边缺陷在役容器是否合乎使用的判断具有一定指导意义     

平面药包抛掷爆破的漏斗特征解析

根据惠州港通用码头陆域平面药包抛掷爆破的实爆堆积测量分析成果 ,结合药包设计的主要参数 ,对平面药包产生的爆破漏斗的范围与形态、不同药包部位的残方比与抛掷率、药包的长抗比与圆柱体药包的应力波形演变关系予以解析 ,供硐室爆破的理论研究、模拟试验和总结条形药包特性时参考     

Biologically active secondary metabolites of barley. IV. Hordenine production by different barley lines

Forty-three lines of barley, including ancestral (wild), landraces, Middle Eastern lines, and modern cultivars, were grown under two different sets of environmental conditions. Hordenine production in barley roots was determined at the one-leaf stage by HPLC analysis and, in two lines only, over a period of 35 days. Forty-two of the 43 lines produced significant amounts of hordenine, although there was no variation among groups. Middle Eastern lines had the highest production with 327 µg/g on a dry weight basis. Production was, however, determined more by environmental conditions during growth than by genetic factors. Hordenine production was up to seven times higher in plants grown under lower light intensities.     

Application of boundary element method to 3-D problems of coupled thermoelasticity

This paper deals with a new boundary element method for analysis of the quasistatic problems in coupled thermoelasticity. Through some mathematical manipulation of the Navier equation in elasticity, the heat conduction equation is transformed into a simpler form, similar to the uncoupled-type equation with the modified thermal conductivity which shows the coupling effects. This procedure enables us to treat the coupled thermoelastic problems as an uncoupled one, A few examples are computed by the proposed BEM, and the results obtained are compared with the analytical ones available in the literature, whereby the accuracy and versatility of the proposed method are demonstrated.     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

用有限带宽反射波波形分析法进行储层横向预测

以正演地震模拟为基础的有限带宽反射波渡形分析法是一种新的储层横向预测方法。首先利用波形分解确定地震反射层的地质属性,找出能反映岩性变化的反射波波形特征参数;然后,采用多元数据聚类分析和灰色系统理论完成储层横向的预测。文中以预测江苏 J 凹陷 F 构造上阜二段生物灰岩分布及厚度横向变化为例,简述了反射波波形分析的全过程。预测结果已为钻探证实。     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

Fatigue crack growth analysis of welded aluminium RHS T-joints with manipulated residual stress level

The fatigue life of a welded aluminium T‐joint made from beams with rectangular hollow section (RHS) has been predicted using a crack propagation analysis and compared with experimental results from joints with different residual stress levels. To include the effect of the residual stresses, the stress ratio was calculated at the weld toe and, via Walker's equation, introduced into the analysis. How to obtain the Walker exponent has been discussed in detail. The introduction of a stress ratio at the weld toe provides good agreement between the experimentally and analytically found S–N curves. The effect of the residual stress was successfully included in the analysis.     

Control of Titanium Alloy Thin Plate Welding Distortion by Trailing Peening

The technology of trailing peening is a kind of promisingly bran-new technology which can be used to control weldingstress and distortion of Ti alloy thin plate. Control of TC4 Ti alloy thn plate welding stress and distortion underthe condition of convent     

Effect of Stress State on Growth of Interfacial Intermetallic Compounds Between Sn-Ag-Cu Solder and Cu Substrates Coated with Electroless Ni Immersion Au

Excessive intermetallic compound (IMC) growth in solder joints will significantly decrease the reliability of the joints. IMC growth is known to be influenced by numerous factors during the component fabrication process and in service. It is reported that, other than temperature and holding time, stress can also influence the IMC growth behavior. However, no existing method can be used to study the effect of stress state on IMC growth in a controlled manner. This paper presents a novel method to study the effect of stress on interfacial IMC growth between Sn-Ag-Cu solder and a Cu substrate coated with electroless Ni immersion Au (ENIG). A C-ring was used and in-plane bending induced tensile and compressive stresses were applied by tightening the C-ring. Results revealed that in-plane compressive stress led to faster IMC growth as compared with in-plane tensile stress.