焦粉四辊破碎机高硬度辊皮切削的新工艺

分析了高硬度辊皮的磨损情况；改进了辊皮的切削方案；满足了生产需求并提高了作业率。     

大庆油田深层岩石力学特性参数的试验研究

通过对岩石可钻性、硬度、抗压强度等参数的测量 ,对大庆油田深井不同深度、不同层位、不同岩性的具有广泛代表性的岩心进行试验。并通过线性回归分析 ,建立了适用性较广的钻井岩石力学特性参数预测模型 ,为深井钻头选型提供了依据。     

In Situ FTIR Study of the Formation of an Organosilane Layer at the Silica/Solution Interface

An FTIR experiment especially designed to study the growth of an organosilane layer at the interface between a solution and a flat silica surface is presented. High sensitivity is achieved by using the attenuated total reflection (ATR) technique in a liquid flow cell. The ATR crystal, either silicon or germanium, is covered with a very thin silica layer. Chemical reactions of a mono-and a di-hydrolyzable silane with the silica substrate have been investigated. The grafting of a submonolayer of the first reagent has been monitored by following the C-H and SiO-H vibrations. The density of grafted molecules has been estimated and information on the nature of the chemical bonding has been achieved. Evidence for the chain-polymerization of the dihydrolyzable silane at the substrate/solution interface has been inferred from the appearance of a Si-O-Si absorption band.     

Hardness-stress-strain correlation in aluminium—A simpler alternative to visioplasticity in metal forming

Local stress and strain variations in the deformation zone can be ascertained by measuring hardness. Hardness is correlated with strain and stress. The expressions discussed later are useful in determining the local variations in stress and strain from hardness measurement. It is a simple method compared to visioplasticity. One can estimate the forces required for a forming process. It helps in the choice of equipment, design of tooling and selection of lubricant for the particular process.     

Effect of Microstructure on the Accelerated Creep of 20CrMoV12‐1 and P 91 Steels

In the initial part the change of microstructure for steel X20 CrMoV 121 is discussed in terms of the distribution of carbide precipitates and its effects on accelerated creep resistance and hardness are presented. In the following, experimental results of microstructure and accelerated creep resistance are presented for the steels X20CrMoV 121 and P91 annealed for up to 8760 hours at 650°C and 750°C before the testing. A similar evolution of the distribution of carbide particles of a size above 102 nm is found for both steels, while the accelerated creep resistance is diminished much stronger for the steel X20CrMoV 121. This difference is due to a greater stability of NbC than that of VC precipitates, both related to the evolution of the chemical composition of complex chromium, molybdenum and iron carbide particles.     

基于正则总体最小二乘准则的OFDM系统信道估计算法

基于导频的最小二乘(LS)估计方法的优点是结构简单,容易实现,但对噪声和干扰敏感。通过对OFDM系统中由于信道的时变性产生的载波间干扰进行了分析,在此基础上提出正则总体最小二乘(TLS)信道估计算法。根据Tikhonov正则化原理,导出了总体最小二乘正则化解法的计算公式。与一般的LS信道估计相比,TLS方法同时考虑了信道噪声和信道时变特性,所以该算法不仅在一般的信道条件下具有良好的性能而且也适合快变信道条件下的OFDM系统。仿真结果表明,该算法具有很好的均方误差和误比特率性能。     

关于饱和软土地基堤坝边坡稳定分析总应力法的讨论

在饱和的软土地基上修筑堤坝,由于孔隙水压力不易准确测定,需采用“φ=0”的总应力法进行稳定分析。这一做法在国外已明确纳入设计规范,在国内工程界较少受到重视,导致过高地估计了安全系数。本文首先系统地回顾了临界状态土力学中的伏斯列夫强度理论,在理论上阐述了饱和软土地基快速填筑时采用总应力法的原因,同时引用了Bishop和Bjerrum、美国联邦公路局、美国陆军工程师团与我国水电水利工程边坡设计规范的相关条文,确认在饱和软土地基采用总应力法进行稳定分析的合理性。以花敖泡土石坝和拉哇水电站围堰为工程实例,分别采用对土的固结不排水剪的两种做法开展稳定性分析,结果表明,直接将土的固结不排水剪强度指标ccu与φcu作为填筑后的强度参数,将严重高估其安全系数。因此建议正在修订的碾压式土石坝与边坡设计规范增加相应条文,并期望引起工程界对这一问题的重视。     

RE型活化剂对氮碳共渗渗层性能的影响

研究了RE 型活化剂对45#、40Cr钢氮碳共渗的渗层硬度及深度的影响。结果表明:RE 型活化剂使渗层硬度和深度都得到了很大提高。     

耐腐蚀摩托艇ADC12-0.5La铝合金微观组织及制备

为改善ADC12铝合金的耐腐蚀性能,通过超声熔铸法制备ADC12-0.5La铝合金,并利用光学显微镜、扫描电镜、能谱分析仪、硬度计、浸泡腐蚀试验和电化学工作站研究了T6热处理和稀土La改性对ADC12铝合金的微观组织、硬度和耐腐蚀性能的影响。结果表明,T6态ADC12-0.5La铝合金微观组织明显细化,α-Al尺寸减小,形貌变圆整,共晶Si相和AlFeMnSi相细化为短棒状。相比于ADC12铝合金,T6态ADC12-0.5La铝合金硬度达到117.7HV,提高了26.8%,腐蚀电流密度降低了10.7%,腐蚀电位上升了64.4%,腐蚀速率降低了54.4%,腐蚀表面平坦且光滑,表现为较轻微的晶间腐蚀。T6态ADC12-0.5La铝合金提高了腐蚀电位,Al-La-Cu稀土相阻碍了电子移动,铝合金的耐腐蚀性能得到大幅度提高。     

扫描速度对硼铸铁气缸套表面钨极氩弧硬化效果的影响

研究了钨极氩弧扫描速度对硼铸铁表面硬化效果的影响规律。结果表明：扫描速度增加,硬化层宽度、深度减小,而硬度提高,裂纹率增大；硬化层硬度沿层深的分布是从表及里由高而低,在过渡区下降缓慢；沿层宽的分布是层中心最高,向两侧逐渐降低,直至硼铸铁基体达到最低值；在保证不出现裂纹的条件下,硬化层表面的最高硬度值可达61．4HRC,硬化层最高显微硬度值可达1156．4HV0．1；硼铸铁材料采用氩弧热源淬火时,淬硬层与基体之间过渡区明显,硬化区组织为莱氏体,过渡区为马氏体、残余奥氏体和少量石墨。