Growth of Fe on Si (100) at room temperature and formation of iron silicide

Low-energy electron diffraction (LEED), Auger electron spectroscopy and X-ray photoelectron spectroscopy (XPS) investigations of both the growth of an iron film on silicon (100) at room temperature and the subsequent formation of iron silicide are the subjects of this paper. An in-situ cleaned silicon (100) wafer without carbon or oxygen contamination exhibiting the known 2 × 1 reconstruction in the LEED pattern served as the substrate. Iron was deposited on this reconstructed surface at 300 K. The comparison of theoretical calculations based on three growth mechanisms with XPS data obtained with take-off angles of 0° and 50° clearly demonstrates a layer-by-layer growth of the iron film on silicon (100). At 300 K no formation of iron silicide was observed, although an interaction between iron and silicon could be detected at the interface. The formation of iron silicide was observed at annealing temperatures of 630–730 K. Quantitative XPS analysis yields the presence of FeSi₂, when the thickness is large enough. Neither the iron film on silicon nor the silicide shows any LEED pattern.     

Subsurface structures in initial stage of FeSi2 growth studied by high-resolution Rutherford backscattering spectroscopy

The initial stage of iron silicide formation is investigated by high-resolution Rutherford backscattering spectroscopy. During the Fe deposition on Si(001) at 470 °C, the formation of FeSi₂ is confirmed by the surface peak analysis. Initially, FeSi₂ grows epitaxially so that one of the major crystallographic axes is parallel to the <111> axis of the Si substrate. With increasing Fe deposition, the deviation between the major crystallographic axis of the silicide region and Si<111> increases although the electron diffraction pattern is independent of the amount of Fe deposition. Therefore, the subsurface crystallographic structure of iron silicide is transformed from a cubic-like to a low-symmetry structure.     

OFA-II型定量荧光仪在油气勘探中的应用

定量荧光仪在现场应用中受到各种因素的影响:如岩屑样品浸泡时的干、湿;图谱是否出现了淬灭;环境温度的影响等等。文章通过具体事例给出解决这些问题的办法。     

In-situ ESR spectroelectrochemical studies of overoxidation behaviour of poly(3,4-butylenedioxythiophene)

The behaviour of poly(3,4-butylenedioxythiophene) (PBuDOT), a relative of poly(3,4-ethylenedioxythipohnene) PEDOT within the poly(3,4-alkylenedioxythiophene) family, has been investigated at potentials above its electrochemical stability threshold using in situ ESR spectroelectrochemistry. The aim was to investigate the effect of electrochemical overoxidation on the charge carrying species, namely polarons, normally generated and annihilated during reversible redox doping and dedoping reactions, by determining the potential dependencies of spectroscopic parameters of the ESR spectra of the polymer over a selected potential range. Specific features of the trends of these dependencies allowed also for an evaluation of presence of the second type of charge carrying species—diamagnetic bipolarons and the effects of their interactions with polarons at different potentials. Around 1.5 V, where the boundary of electrochemical stability of the polymer lies, sharp drop of the concentration of paramagnetic centres has been observed together with a transitory narrowing of the ESR line. These changes were found to be irreversible as evidenced by the course of subsequent reduction half-cycle, which differed from the one for a not overoxidised polymer, observed in previous studies. Aided by the results of electrochemical studies it was concluded that the overoxidation process leads to a degradation of the polymer most probably due decrease of the conjugation length of the main chain π-bond through cross-linking or addition reactions. While the electrochemical results pointed to a non-complete degradation of the polymer, the specific parameters of the ESR line in the reduction half-cycle indicate that the remaining spins are confined to isolated segments of a partially degraded polymer where their behaviour resembles oligomer-like radicals.     

Structural Description of Polyaromatic Nucleus in Residue

The proton nuclear magnetic resonance spectroscopy （1H-NMR）, the synchronous fluorescence spectrometry （SFS） and the ruthenium ions catalyzed oxidation （RICO） method were used to determine the chemical structure of polyaromatic nucleus in Oman residue fractions. The results of 1H-NMR analyses showed that the average numbers of aromatic rings in the aromatics, resins and asphaltenes units were 3.2, 5.6 and 8.2, respectively. SFS was used to investigate the distribution of aromatic rings in residue fractions, the main distribution range of aromatic rings in aromatics, resins and asphaltenes were 3 4 rings, 3--5 rings and more than 5 rings, respectively. The aromatic network in residue fractions was oxidized to produce numerous carboxylic acids. The types and content of benzenepolycarboxylic acids, such as phthalic acid, benzenetricarboxylic acids, benzenetetracarboxylic acids, benzenepentacarboxylic acid and benzenehexacarboxylic acid disclosed the condensed types of aromatic nuclei in the core. The biphenyl fraction （BIPH）, the cata-condensed fraction （CATA）, the peri-condensed fraction （PERI） and the condensed index （BCI） were calculated based on the benzenepolycarboxylic acids formed. The results implied that there was less biphenyl type structures in all residue fractions. The aromatics fraction was almost composed of the cata-condensed type system, and the asphaltenes fraction was wholly composed of the peri-condensed type system, while in the resins fraction co-existed the two types, herein the peri-con- densed type was predominant over the cata-condensed type. Based on the analytical results obtained in the study, the components --aromatics, resins and asphaltenes -- were given the likely structural models.     

Determination of instantaneous corrosion rates and runoff rates of copper from naturally patinated copper during continuous rain events

Instantaneous corrosion rates of naturally patinated copper of varying age (16 months, 138 and 145 years) have been determined during continuous rain events in the laboratory with electrochemical impedance spectroscopy using a two-electrode cell. The two-electrode cell was found to yield the same information in bulk rainwater as a conventional three-electrode cell.Relatively constant corrosion rates, between 0.2 and 0.6 μm/y, were determined for samples having a two-layer structure with an inner brownish layer of cuprous oxide and an outer greenish layer of basic copper salts (138, 145 years). Samples with cuprous oxide as the dominating phase of the patina (16 months) showed higher and somewhat increasing corrosion rates during a rain event (from 0.6 to 1.2 μm/y). During a continuous rain event, corrosion rates were found to be approximately 10 (brownish patina) and 25 times (greenish patina) lower than corresponding instantaneous runoff rates. The first flush phenomena of the runoff process, with an increased concentration during first flush and a relatively constant concentration during steady state, was indirectly seen as an increase in solution conductivity during the first rain volume followed by relative constant value. The contribution of the concentration in the first flush to the total annual runoff rate was significant for panels having a greenish layer (138, 145 years) whereas it was negligible for panels having a brownish layer (16 months).     

Hybrid gas-to-particle conversion and chemical vapor deposition for the production of porous alumina films

Porous alumina films can be found in a wide variety of materials, including filters, thermal insulation components, dielectrics, biomedical and catalyst supports, coatings and adsorbents. Production methods for these films are as equally diverse as their applications. In this work, a hybrid process based upon chemical vapor deposition and gas-to-particle conversion is presented as an alternative technique for producing porous alumina films, with the main advantages of solvent-free, low substrate-temperature operation. In this process, nanoparticles were produced in the vapor phase by reaction of aluminum acetylacetonate in the presence of oxygen. Downstream of this reaction zone, these nanoparticles were collected via thermophoresis onto a cooled substrate, forming a porous film. Some deposited films were subjected to post-processing in the form of annealing in air. Fourier-transform infrared spectra and X-ray energy-dispersive spectroscopy analysis confirmed the production of alumina at processing temperatures above 973 K. X-Ray diffraction revealed that the films were amorphous. Film thickness, ranging from 30 to 250 μm, and the average deposition rate were determined from scanning electron microscopy results. From transmission electron microscopy, the average primary particle size was determined to be approximately 18 nm and the formation of nanoparticle aggregates was evident. Annealing of the films at temperatures ranging from 523 to 1173 K in the presence of air did not have an effect on particle size. The specific surface area of the powder composing the films ranged from 10 to 185 m² g⁻¹, as determined from nitrogen gas adsorption by the Brunauer–Emmett–Teller method.     

Approximate channel identification via δ‐signed correlation

A method of approximate channel identification is proposed that is based on a simplification of the correlation estimator. Despite the numerical simplification (no multiplications or additions are required, only comparisons and an accumulator), the performance of the proposed estimator is not significantly worse than that of the standard correlation estimator. A free (user selectable) parameter moves ‘smoothly’ from a situation with small sum‐squared channel estimation error but hard‐to‐identify channel peaks, to one with a larger sum‐squared estimation error but easy‐to‐identify channel peaks. The proposed estimator is shown to be biased and its behaviour is analysed in a number of situations. Applications of the proposed estimator to sparsity detection, symbol timing recovery and to the initialization of blind equalizers are suggested. Copyright © 2002 John Wiley & Sons, Ltd.     

Mössbauer spectroscopic studies of Fe-substituted YIG

Compositional dependence of hyperfine parameters, determined through Mössbauer spectral analysis has been studied for Y_3−xFe_5+xO₁₂ (x = 0.0, 0.1, 0.3 and 0.5) garnet system at 300 K. The Mössbauer spectra have been fitted with three sextets in the ferrimagnetic state corresponding to Fe³⁺ ions at tetrahedral (d), octahedral (a) and dodecahedral (c) sites of the crystal structure. It is observed that isormershift, quadrupole shift and hyperfine field of d-site show no significant variation with Fe³⁺ concentration. The change in hyperfine fields of a- and c-sites with composition (x) has been explained on the basis of strength of exchange integrals, change in isomershift can be understood due to s-electron charge distribution and asymmetric displacement of oxygen ions surrounding the a- and c-sites seems to be responsible for observable quadrupole shift. The magneton number values obtained from magnetization and Mossbauer data are in agreement to those calculated using Neel's three sublattice model of ferrimagnetism.     

账面盈利与经营活动现金净流量的相关性研究——基于金属非金属行业上市公司的实证分析

对2004年中国证券市场上的129家金属和非金属行业上市公司的会计账面盈利与现金流量的相关性进行实证研究后,发现两者的相关程度很低,很大一部分上市公司的账面盈利没有形成相应的现金流入,导致两者之间产生“滞脱”的效应.因此,笔者认为在对企业的财务状况进行评价时,不能仅仅局限于使用一些反映企业账面盈利的指标,应该还需要考虑一些反映企业创造现金流量能力的指标.