Suppression of photo-induced dilation in cyanide treated hydrogenated amorphous silicon films

Effects of cyanide (CN) treatment with hydrogenated amorphous silicon (a-Si:H) films have been investigated. The decrease of ΔV/V was observed in cyanide treated a-Si:H films and the successive thermal annealing at 200°C after CN treatment induced the further reduction of the ΔV/V. XPS spectra show the indirect evidence that the cyanide species is present within 10 nm from the hydrogenated amorphous silicon surface. The results of CN treatment with a-Si:H solar cells are demonstrated.     

高浓度焦化废水的预氧化-混凝处理研究

焦化废水成分十分复杂,污染物浓度高,性质非常稳定且水量大,是典型的难降解有机废水。使用H2O2为氧化剂,FeSO4.7H2O为催化剂的Fenton氧化法对钢铁焦化厂废水的终冷水进行了试验研究,氧化处理后用FeCl3为混凝剂对COD,NH3-N,色度及浊度的去除率进行了系统的考查。确定了氧化反应的影响因素和最佳的混凝实验条件。结果表明:当pH值控制在3左右,反应时间为30 min,反应温度为80℃,焦化废水的COD,NH3-N,浊度和色度去除率分别达到了93.1%,96.2%,90.8%和90.2%。     

Evaluation of capital cost data. part 7: Liquid waste disposal with emphasis on physical treatment

Capital cost correlations are given for oil-water separators, equalization basins, primary clarifiers, clarifiers and clarifier mechanisms, reverse osmosis unit, ultrafiltration units, gravity filters and miroscreens. Data are included for raw sewage, intermediate and recirculation pumping stations and for preliminary treatment (or bar screens, grit removal, overflow and bypass chamber and Parshall flume), for grit removal, comminution and gas stripping. The correlations are accurate to ± 30%, expressed in Canadian dollars and adjusted to a Marshall and Swift value of 1000. Details as to what components are included in the cost are given. Data are given for the labour and material costs to create a working process module. For inflation indices, a critique of the Engineering News Record, EPA small city, Marshall and Swift, Chemical Engineering and Southam inflation indices suggested that the Marshall and Swift index is most appropriate for the construction and process equipment studied here. Concerning the currency exchange, for the equipment and processes in this study, equipment costs the same whether expressed directly in US or Canadian dollars. To put the current data into perspective, several hundred sources of cost data were analyzed. The major correlations are compared, on a consistent basis, with current data.     

铸铝激光熔融处理后的组织与性能

应用光学和电子显微镜及显微硬度计研究了铸造Al-Si合金经激光表面熔融处理后的组织和性能。指出,组织分熔化区、过度区和基体三层。在熔化区中树枝状先共晶α相的平均宽度由原始组织的20～40μm细化到2～3μm,同时共晶组织也被大大细化。这些变化使显微硬度值由67.4提高至109～115.     

含过期火药粉状工业炸药的研究

文章概要论述了一种新型民用炸药－含过期火药粉状工业炸药在配方、制造工艺等方面所进行的实验研究。结果表明，该炸药性能良好、制造技术安全可靠，值得推广。     

K418B合金细晶铸造整体涡轮真空热处理工艺研究

通过力学性能评估和金相组织观察，研究五种热处理制度，两个周期的试验结果，确定了Ｋ４１８Ｂ合金细晶铸造整体涡轮的真空热处理工艺。     

Influence of the surface conditions on permeation in the deuterium–MANET system

The condition of the surfaces is of crucial importance for the deuterium permeation through materials. In this work a study of the surface constants for the adsorption (σk₁) and release (σk₂) of deuterium under different surface conditions on the martensitic steel DIN 1.4914 (MANET) has been carried out. The growth of an oxide surface layer (Cr₂O₃) of about 25–30 nm in a MANET sample, heat treated in an oxidizing environment, compared to the bare MANET that have a ‘natural' oxide of about 5 nm has provoked a reduction of both the permeation rate and the recombination coefficient (about 3 orders of magnitude). In addition, the permeation governing process has changed from diffusion-limited to surface-limited. The measurements of the permeation rate of deuterium were performed by a gas-phase permeation technique over the temperature range 574–746 K and for deuterium driving pressures in the range from 3 to 10⁵ Pa.     

超细分子筛材料的合成与应用研究进展

综述了近几年超细分子筛的合成与应用方面的研究进展,重点介绍了几种常用且研究较多的分子筛,主要包括Y,ZSM-5,β,Silicalite-1,ZSM-35,MCM-22等分子筛。对超细分子筛的合成方法及其在石化、环保和生物等领域的应用进行了介绍,并对分子筛复合材料的研究及应用的最新动态进行了评述,说明超细分子筛材料的应用领域仍在不断拓宽,超细分子筛复合材料的研究将会成为分子筛材料领域未来的重要发展方向。     

时效处理对 TiNi 合金相变与性能的影响

通过用ＴＥＭ等方法研究热处理制度（固溶处理、时效处理）对ＴｉＮｉ合金相变组织和性能的影响，找出了最佳热处理制度。结果表明，在４５０～５００℃进行时效处理，Ｔｉ－５０．８ａｔ％Ｎｉ的合金出现了大量的Ｔｉ３Ｎｉ４相，且恢复率最高。     

新型废水厌氧处理工艺——内循环厌氧反应器

介绍内循环(IC)厌氧反应器的发展、基本结构、运行机理。分析该反应器的工艺过程,指出该工艺具有处理效率高、抗冲击能力强等优点。针对IC反应器存在的缺陷,人们对该反应器进行技术改进:通过提高它的内循环的气量进行处理低浓度有机废水;增加外循环装置缩短IC反应器的启动周期。