Al-10Mg型固溶合金自然时效稳定性研究

测定了ZL30 5合金自然时效 33年的力学性能变化 ,观察了晶界的析出相 ,研究了组织和性能的关系 ,从而确定了ZL30 5合金具有长期自然时效稳定性。     

微流控分析芯片制作中的低温键合技术

微流控分析芯片制作方法的研究是微流控分析的基础。制作性能良好的微流控分析芯片时,基片与盖片的键合技术十分重要。本文针对近年来发展迅速的低温键合技术,对各种方法进行了评价,并对其发展前景进行了展望。     

Curie Temperatures of III–V Diluted Magnetic Semiconductors Calculated from First-Principles in Mean Field Approximation

Electronic structure and ferromagnetism in III–V compound-based diluted magnetic semiconductors (DMS) are investigated based on first-principles calculations by using the Korringa-Kohn-Rostoker method combined with the coherent-potential-approximation. The stability of the ferromagnetic phase in GaN-, GaAs-, GaP-, GaSb-based DMS is investigated systematically. The calculations show that 3d-impurities from the first-half of the transition metal series favor the ferromagnetic state, while impurities from the latter-half of the series exhibit spin-glass behavior. This chemical trend in the magnetism is explained by the double exchange mechanism taking the local symmetry at the impurity gap states into account. Curie temperatures of GaAs- and GaN-based DMS are estimated by using the Heisenberg model in a mean field approximation with the parameters calculated from first-principles. It is suggested that room-temperature ferromagnetism can be realized in these systems.     

The Soft-Contact Method and Instruments for Measuring the Surface Temperature of Solids

A method and instruments based on it are proposed for the contact measurement of surface temperature when carrying out industrial experiments and when monitoring technological parameters.     

低温脂肪酶产生菌的筛选、鉴定及其部分酶学性质

从南极乔治王岛冻土来源的76株低温细菌中筛选到13株低温脂肪酶产生菌，对其中的BTsl0022菌株进行鉴定。通过生理生化特征、16s rDNA基因序列的同源性和系统发育分析发现，菌株RTsl0022属于假单胞菌属(Pseudomonas)，但与已定名的假单胞菌有一定的差异，与未定名的Pseudomonas sp．PsB的亲缘关系最接近，故将其暂定名为Pseudomonas sp．BTsl0022。对该菌脂肪酶的酶学性质初步研究表明，酶的最适作用温度为24℃，对热敏感，60℃处理30min仅残留25％酶活性，酶的适宜作用pH范围在7．0～9．0，最适pH为8．0。     

高温氨化合成GaN微晶

分别利用Ga2O3粉末和Ga2O3凝胶作为Ga源,采用NH3为N源,在950℃下,分别将两种反应物与流动的NH3反应20 min合成了GaN微晶。用X射线衍射(XRD)、扫描电子显微镜(SEM)、选择区电子衍射(SAED)对微晶进行结构、形貌的分析,特别是对两种不同途径合成GaN微晶的XRD进行了分析比较。结果表明,当Ga源温度为950℃时两种不同的合成途径均可得到六方纤锌矿结构的GaN单晶颗粒,在氮化温度为850℃和900℃时,利用Ga2O3粉末作为Ga源,仅有少量的Ga2O3转变为GaN;而采用Ga2O3凝胶作为Ga源,在相同的温度下,大部分凝胶经过高温氨化反应均可转化为GaN。     

Volumetric Change and Surface Properties of Temperature-Sensitive Polyvinylalcohol (PVA) Hydrogel

Polyvinylalcohol (PVA) polymer gel is a temperature sensitive polymeric gel, with a critical transition temperature (with H₂O) of 310 K. At higher than 310 K, this temperature sensitive polymer gel shrinks because of discharging water, whereas at lower temperatures, the gel swelled because of absorbing water. The reversibility of the gel's volume change was confirmed by temperature swing. The adsorption behavior of an organic compound onto the PVA polymer gel in water was tested at various temperatures. The amount of adsorbed organic compound increased remarkably at temperatures higher than about 310 K. Then, it was confirmed that the organic compound in PVA polymer gel could be reversibly adsorbed and desorbed by a temperature change between 293 and 323 K. The mechanism of adsorption of the organic compound onto the PVA polymer gel could be explained by hydration and dehydration of polymer gel.     

天然气吸附储存脱附过程的动态模拟

通过热动力学计算,认识了脱附过程当中储罐内温度剖面分布的典型特征:储罐轴心处的温度下降幅度最大。分析了脱附过程当中储罐壁的热交换、吸附剂的导热系数以及储罐内的初始压力对储罐内的温度剖面的影响。结论是加强储罐外壁的热交换、增大吸附剂的导热系数皆能改善吸附储罐内的温度剖面。     

高温酸化助排剂HC2-1的研究

为了满足高温油藏和深井酸化作业残酸返排的需要，通过表面活性剂的筛选和复配研究，得到了高温酸化助排剂HC2—1。其性能评价结果表明，HC2—1具有使用浓度低、表面活性高的特点，在20％的HCI溶液中，当其浓度为50mg／L时，表面张力为20．7mN／m；具有良好的耐温性能，在180℃下恒温48h，HC2—1仍保持较高的表面活性；具有良好的耐盐能力，加有HC2—1的20％HCl溶液和CaCO3反应至HCl完全消耗，整个反应过程体系无新相生成且表面张力基本不变；可增大酸液体系的润湿角，进一步降低毛细管阻力，使酸液返排率由46％提高到97％，在促进酸液返排的同时与原油不发生乳化反应。     

低温低渗透砂岩油藏窜流大孔道深部封堵技术研究

所用堵剂为高强度的淀粉接枝聚丙烯酰胺交联凝胶SAMG-1,由<6%淀粉、4.5%-5.5%丙烯酰胺、0.003%-0.006%交联剂组成,35℃成胶时间受淀粉和交联剂用量控制,为18-20小时以上,成胶前黏度-100 mPa.s。该堵剂具有长期稳定性,在储层岩心中注入深度15 cm的堵剂,在35℃候凝48小时后及老化90天后,封堵强度分别为0.61和0.59 MPa/cm,封堵率分别为98.6%和98.1%。该堵剂优先进入高渗层,注入0.5 PV并成胶后,2组双填砂管组成的模型低、高渗管渗透率保留率分别为68.4%、0.7%和69.4%、0.0%。吉林扶余油田西一区+15-8.2区块有水井6口,油井13口,含水率达91.5%,注入水最快在5天内到达油井。报道了该区块整体深部调剖封堵窜流通道的情况,详细叙述了+15-9.2井施工中通过注入压力和井底回压控制注入流量,使堵剂陆续进入原生和次生孔道的工艺作业,该井设计注入堵剂92 m3。6口水井整体调剖后,油井产液量差别减小,产油量增加,有效期已超过了9个月,共增油843 t,含水平均下降3.87%。图7表1参8。