饱和砂土吸力基础沉贯过程中渗流场分布

针对不同长径比的传统吸力基础及裙式吸力基础,采用有限元数值模拟的方法,研究其在饱和砂土内吸力沉贯过程中的土体渗流场分布规律。研究结果表明:传统吸力基础在沉贯过程中,土中渗流场均呈现层状分布,水头等值线密集分布于主桶内部土体,相对比较平缓;而主桶外部水头等值线变化较小且分布比较稀疏。裙式吸力基础渗流场主要存在于主桶内部和裙结构内部,并向外扩散至部分土体。吸力沉贯过程中土体的水头损失主要集中在主桶内部和裙结构内部,土体中的孔压分布和传统吸力基础规律一致,即成层状分布并未出现泡状的孔压分布形式。研究成果对揭示吸力基础沉贯机理有理论指导意义。     

加筋胶结砂砾石力学特性试验研究

通过应变控制式三轴试验,对比研究了在不同围压作用下,胶结砂砾石中加入不同纤维含量时的力学性能。试验结果表明:加筋胶结砂砾石在力学性能方面表现为一种典型的应变软化材料。与无加筋胶结砂砾石相比,加筋胶结砂砾石的初始模量和峰值强度变化很小,但峰值强度出现延后现象,残余强度得到明显提高,脆性指数下降,粘聚力、内摩擦角等力学性能参数明显提高。工程应用方面,加筋胶结砂砾石作为一种新型材料具有广泛的工程应用前景。     

脱硫石膏粉煤灰胶结材水化硬化机理及耐水性研究

以火电厂的两种废渣即脱硫石膏和粉煤灰为主要原料制得的胶结材，其强度明显高于普通石膏制品，软化系数大于０．８５。采用水化热测定、ＸＲＤ和ｐＨ值测定及ＳＥＭ／ＥＤＸＡ分析，并结合宏观试验结果，分析了这种胶结材的水化硬化机理和微结构特点，并对其耐水性提高的原因进行了讨论。     

磷石膏生产墙体材料可行性研究

通过正交试验获得磷石膏—矿渣—粉煤灰—石灰—水泥胶凝体系的优化配合比为磷石膏∶矿渣∶粉煤灰∶生石灰∶水泥=30∶25∶24.5∶10.5∶10,并通过XRD、SEM微观分析手段和宏观测定强度的方法探讨了养护制度对该胶凝体系性能的影响。研究结果表明：该胶结料90℃下蒸养7 h,然后自然养护,28 d抗压强度高达43.9MPa,凝结时间正常,耐水性良好。胶结料强度随养护温度的升高而增加;90℃下,胶结料强度随蒸养时间的增加而增加,此温度下蒸养13 h所得制品,7 d抗压强度便达到39.6 MPa。利用最优配比成型的免烧砖能达到非烧结粘土砖15级的要求。     

砂桩加固可液化地基的振动台试验研究

饱和砂土地震液化问题是岩土地震工程中一个重要的研究课题,利用振动台在室内开展相关研究是一种行之有效的方法.利用小型振动台模型试验研究散体材料加固可液化地基,得出不同桩距下孔隙水压力的变化规律,探讨不同桩距对抗液化效果的评价.试验表明,桩距在3～3.5桩径时,孔隙水压力最小,抗液化效果最佳;而且得出浅层土比深层土更易液化的结论.建议在实际设计中桩距取3～3.5桩径,并且长短桩结合使用,既能取得良好的加固效果又能降低工程造价.     

砂土各向异性和不排水剪切特性研究

在不同应力路径下,进行三轴和扭剪不排水剪切试验,揭示砂土力学行为与应力路径和各向异性的关系,并对砂土的细观结构和各向异性进行量化.研究结果表明,砂土的力学特性受材料各向异性和应力各向异性耦合影响.砂土各向异性的量化研究和力学试验结果为后续本构模型发展提供了依据.     

考虑中主应力效应Gudehus-Bauer亚塑性模型的改进

针对Gudehus-Bauer亚塑性模型不能考虑中主应力影响,在Gudehus提出的响应包络线理论基础上,提出了在模型的非线性项乘以一个考虑中主应力的因子进行改进.这种改进增加了土体剪切时的强度,改变了土体受压时的变形.新模型对中主应力的变化在中主应力参数影响程度能够有一定反映.同时将改进后的模型与中主应力参数为常量的真三轴实验进行了比较.结果表明改进后的模型可以模拟中主应力对砂土强度和变形特性的影响,能够定量预测由于中主应力影响产生的体积应变.     

Cemented backfill technology based on phosphorous gypsum

Physical-chemical properties of phosphorous gypsum, proportion and cemented mechanism of slurry with gypsum as aggregate were studied to remove the harms of gypsum pile, combining with difficult problems of excessive mined-out gobs, enormous ore body under roadway and low recovery ratio of Yongshaba Mine, Kaiyang Phosphor Mine Group, Guizhou Province, China. An appropriate backfill system and craftwork were designed, using shattering milling method to crush gypsum, double-axles mixing and strong activation mixing way to mix slurry, cemented slurry and mullock backfill alternately process. The results show that gypsum is fit for backfilling afterwards by adding fly ash, though it is not an ideal aggregate for fine granule and coagulate retardation. The suggested dosage (the mass ratio of cement to fly ash to gypsum) is 1:1:6–1:1:8 with mass fraction of solid materials 60%–63%. Slurry is transported in suspend state with non-plastic strength, and then in concretion state after backfilling. The application to mine shows the technology is feasible, and gypsum utilization ratio is up to 100%. Transportation and backfill effect is very good for paste-like slurry and drenching cemented slurry into mullock, and the compressive strength and recovery ratio are 2.0 MPa and 82.6%, respectively, with the maximum subsidence of surface only 1.307 mm. Furthermore, the investment of system is about 7×10⁶ yuan (RMB), only 1/10 of that of traditional paste backfill system. Foundation item: Project (2006BAB02A03) supported by the National Key Technology Research and Development Program; Project (08MX16) supported by Mittal Scientific and Technological Innovation Projects of Central South University during 2008     

Constitutive equations and finite element implementation of strain localization in sand deformation

A recently proposed model coupling with the solid-fluid of the saturated sand was utilized to study the deformation band. Based on the critical state plasticity model by Borja and Andrade, the hydraulic conductivity tensor was naturally treated as a function of the spatial discretization matrix about the displacement and the stress field, allowing a more realistic representation of the physical phenomenon. The fully Lagrangian form of the Darcy law was resolved by Piola algorithm, and then the flow law was gained, leading to the implementation of a modified model of the saturated sand. Then the criterion for the onset of localization was derived and utilized to detect instability. The constitutive model was implemented in a finite element program coded by FORTRAN, which was used to predict the formation and development of shear bands in plane strain compression of saturated sand. At last, the formation mechanism of the shear band was discussed. It is shown that the model works well, and the simulation sample bifurcates at 1.18% axial strain, which is in a good qualitative agreement with the experiment. The pore pressure greatly affects the onset and development of the deformation band, and it obviously increases around the localization-prone regions with the direction toward the outer side of the normal of the shear band, while the pore stress flows nearly horizontally and is distributed equally far away the shear band region. Foundation item: Project(2006G007-C) supported by the Foundation of the Science and Technology Section of Ministry of Railway of China; Project(77206) supported by the Excellent PhD Thesis Innovation Foundation of Central South University, China     

基于改进一次二阶矩法的砂土液化判别方法

通过对改进一次二阶矩可靠性分析方法进行研究,提出了一种基于标准贯入击数极限状态方程的地震液化可靠度评估方法,并用Matlab 7．0编制了相应的地震液化概率判别程序。用该可靠性分析方法对1976年河北唐山大地震的资料进行了液化概率分析,并与实测值和规范判别法计算结果进行了对比。结果表明：该方法具有可行性和精确性,为砂土液化势评估提供了一种有效的新方法。