Numerical Simulation of Deforming Manufacture Process for Automobile Bevel Gear Blank

1 Introduction Rear axle bevel gearis a vital kind of annular accessory with high precision and hugeload availablefeatures ,andit is widely used as the differential drive in automobiles and tractor .In China ,the traditional manufactureapproach of producing the rear axle bevel gear blankis die forging,which not only requires a highinvestment ofproduct equipments , but also involves a low material utilization and great noise .In order to overcome thesedrawbacks , manyresearchers have done a gre…     

Continued fraction for formal laurent series and the lattice structure of sequences

Besides equidistribution properties and statistical independence the lattice profile, a generalized version of Marsaglia's lattice test, provides another quality measure for pseudorandom sequences over a (finite) field. It turned out that the lattice profile is closely related with the linear complexity profile. In this article we give a survey of several features of the linear complexity profile and the lattice profile, and we utilize relationships to completely describe the lattice profile of a sequence over a finite field in terms of the continued fraction expansion of its generating function. Finally we describe and construct sequences with a certain lattice profile, and introduce a further complexity measure.     

Single and combined deactivating effect of alkali metals and HCl on commercial SCR catalysts

Two commercial SCR catalysts, with a nominal W content of about 9 wt.% and a V nominal content of 0.55 and 1.8 wt.%, respectively, were contacted with different amounts of Na and K and with HCl vapours in order to simulate poisoning by species more specifically contained in exhaust gases from MSW combustion. Catalysts were characterised using XRD analysis, SEM/EDX analysis, BET and pore size distribution measurements, NH₃ TPD, TG analysis. Poisoning agents do not cause loss of surface area nor pore occlusion. A significant loss of surface acidity was observed upon alkali metals poisoning whereas a decreasing of vanadium content was observed for the more concentrated catalysts upon HCl poisoning. Catalysts deactivation is proportional to the number of acid sites neutralised by alkali metals adsorbing ammonia in the temperature range typical of SCR process. HCl promotes the formation of new acid sites showing a lower activity compared to the original one.     

压缩机环状阀工作过程冲击应力的有限元分析研究

针对压缩机环状阀结构和运动特点,利用ANSYS分析软件对其冲击应力进行有限元分析,得出阀片质量和阀片倾侧运动对环状阀工作过程冲击应力的影响。为压缩机环状阀的结构修改和优化设计提供了必要的基础。     

Deflections of highly inflated fabric tubes

Inflatable beams made of modern textile materials with important mechanical characteristics can be inflated at high pressure. The aim of the paper is to present experimental, analytical and numerical results on the deflections of highly inflated fabric tubes submitted to bending loads. Experiments are displayed and we show that tube behaviour looks like that of inflatable panels (Thin-Walled Struct. 40 (2002) 523–536). Equilibrium equations are once again written in the deformed state to take into account the geometrical stiffness and the following forces. The influence of the shear stress cannot be neglected and Timoshenko’s beam theory is used. A new inflatable tube theory is established and simple analytical formulas are given for a cantilever-inflated tube. Comparisons between analytical and experimental results are shown. A new inflatable finite tube element is constructed by use of algebraic operations, because the compliance matrix of the cantilever beam is not symmetric. Comparisons between experimental, analytical and numerical results prove the accuracy of this beam theory and on this new finite element for solving problems on the deflections of highly inflated tubes.     

一种带接口的CMOS10位电流型乘法D／A转换器

介绍了一种带接口的单片ＣＭＯＳ１０位电流型乘法Ｄ／Ａ转换器的设计及工作方式。着重阐述逻辑电平转换、控制逻辑的结构设计及其工作方式。在不修调电阻网络的情况下，该Ｄ／Ａ转换器在５Ｖ、１５Ｖ下，其线性误差、微分误差、满刻度误差均能达到１０位精度     

人工神经网络A／D变换器

本文对［５］的４位人工神经网络Ａ／Ｄ变换器进行了研究．指出按其方法推广实现多位Ａ／Ｄ时存在突触电阻大小以至无法实现且抗干扰能力也不好的问题并给出了解决办法．同时对如何改善神经元转移特性的硬限幅曲线作了简单讨论．     

多路缓变信号记录仪

本文介绍了多路缓变信号记录仪的系统构成,研究设计了多路缓变信号记录仪的硬件电路,较详细地介绍了该系统的工作原理及软件编程要点。     

Stress analysis with arbitrary body force by boundary element method

Linear stress analysis without body force can be easily carried out by means of the boundary element method. Some cases of linear stress analysis with body force can also be solved without the domain integral. However domain integrals are generally necessary to solve the linear stress problems with complicated body forces. This paper shows that the linear stress problems with complicated body forces can be solved approximately without the domain integral. In order to solve these problems, the domain is divided into small areas using contour lines of body force. In these areas, the distributions of body force are assumed approximately to satisfy the Laplace equation.