新型SiMnCr系高强度粗钢筋材料的研制

针对高强度钢筋的性能要求和钢筋生产的工艺特点 ,设计了一种新型的低碳SiMnCr系高强度钢。测定了该钢种的CCT曲线及其力学性能。在锻造或轧态下 ,可获得以低碳马氏体为主含少量贝氏体、残留奥氏体的复相组织 ,经低温回火 ,可获得高的强度 (σb>12 30MPa)和良好的塑性 (δ5≥ 8% )。     

修正步冷温度曲线试验研究

按修正步冷温度曲线对经步冷脆化的 2 .2 5Cr 1Mo和在加氢反应器内运行 5a的 2 2 5Cr 1Mo试块进行了修正步冷试验 ,评定了材料的回火脆性。结果表明 ,按修正步冷曲线进行修正步冷试验能使已经脆化的材料进一步脆化 ,为加氢反应器材料损伤的研究提供了一条途径。     

改进渣浆泵过流件铸造工艺及硬度的措施

介绍了渣浆泵过流件材质的化学成分及其正交试验的优选过程，以及重新制定的铸造工艺。     

Growth,characterization and electrical anisotropy in GaTe—a natural semiconducting superlattice

GaTe is a III–VI semiconductor which has layered structure with large anisotropy in electrical properties. Growth of single crystals by the Bridgman technique permitted the measurement of thermoelectric power in orthogonal directions from which the anisotropy of hole effective masses were determined for the first time. From resistivity and Hall effect measurements the carrier activation energies and scattering mechanisms between 10–300°K were found. Study of the temperature dependence of conductivity revealed a variety of conduction mechanisms including weak localization below 20°K, hopping conduction between 20–50 K and band conduction in and across the layer planes atT>70 K. Weak localization was confirmed through observation of negative magnetoresistance. TheI–V characteristics showed quantized behaviour due to tunneling across potential barriers, which may be due to stacking faults between layer planes as observed by TEM studies.     

High energy Urbach characteristic observed for gallium nitride amorphous surface oxide

We have observed an “above band-gap” Urbach like characteristic for gallium nitride films (at the high energy side of the band-edge). A combination of X-ray diffraction, secondary ion mass spectroscopy and optical transmission measurements were taken for gallium nitride samples of different thickness. From this data we demonstrate that the high energy Urbach like characteristic is related to the presence of an amorphous surface oxide. It is shown to dominate the absorption spectra of thin gallium nitride samples, for which the influence of surface oxidation is strongest.     

Cr12MoV钢冷挤压成形模强化工艺的研究

针对Crl2MoV钢冷挤压成形模热处理存在的质量问题，对加热温度和方式进行了大量的试验研究，在此基础上，提出了改进的快速加热工艺。结果表明，经该工艺处理后，模具使用寿命得到显提高。     

调质状态下40Cr钢的焊接

在合理制定焊接工艺的基础上，采用R307珠光体耐热钢焊条成功地进行40Cr钢在调质状态下的焊接，解决了通常采用25—13型奥氏体焊条焊接出现的焊缝强度低、焊接接头性能差的问题。     

Simulation of the Forming Behaviour of a Boron Modified P91 Ferritic Steel

The forming behaviour at high temperature of a modified 9%Cr‐1%Mo (P91) ferritic steel containing B and Ti for elevated temperature service was investigated. The microstructure of the as‐received material is mainly martensite at room temperature, but special etching revealed prior austenite grains of about 25 μm in size. Torsion tests were conducted at temperatures in the range 850 to 1250 °C to simulate the hot rolling process under comparable conditions of temperature, strain rate and strain. The deformation data obtained from these tests were correlated with the Garofalo equation with a stress exponent of 4.6 and an activation energy of 315 kJ/mol. This equation was used to predict the formability behaviour for the rolling process and also to determine the maximum forming efficiency and stability of the steel. A temperature of 1200 °C is recommended to conduct the forming process.     

Cr12型模具钢锻造内部裂纹产生的原因及预防

基于Cr12型钢种的特点，归纳了Cr12钢锻造时内部裂纹的类型，分析了内部裂纹产生的原因并提出了相应的预防措施。     

控制W9Cr3Mo4V低倍碳化物剥落的工艺改进

针对W9Cr3M04V轧制成品材低倍碳化物剥落的形成原因分析，得出一次碳化物颗粒粗大、在1／4D至中心区域聚集是导致低倍热酸浸试验碳化物剥落的主因；由此进行冶炼过程中注速（锭形）、浇注温度选择对比工艺试验，得出在原有冶炼＋轧制的工艺基础上选用2．2t锭、降低浇注温度（1489℃）能有效改善一次碳化物颗粒大小和聚集程度，进而有效降低低倍碳化物剥落倾向。