A/O生物除磷工艺丝状菌膨胀的控制

为了有效控制A/O生物除磷工艺处理化粪池污水时产生的丝状菌膨胀,先后采取改变系统的COD污泥负荷(NCOD)、溶解氧(DO)的质量浓度和降低S2-的质量浓度等措施,最终使A/O除磷工艺丝状菌膨胀得到了控制,污泥沉降性能得到了有效恢复.研究结果表明:A/O除磷工艺在高NCOD条件下运行时,容易发生严重的丝状菌膨胀现象,原因是COD在厌氧区降解后仍有较高的剩余量进入好氧区,导致聚磷菌在和丝状菌的竞争中优势变弱;在低NCOD条件下运行时,由于原水中硫化物含量过高导致丝状硫细菌增殖,因此仍然存在轻度的丝状菌膨胀现象.     

脂肪醇生物活性和理化性质的QSAR/QSPR研究

为了研究脂肪醇结构-性质(活性)的定量关系,用相对键长取代拓扑距离,结合距离矩阵,提出了距离调和拓扑指数Te,Te和醇的许多理化性质和生物活性具有良好的相关性.用Te及δ(醇中和羟基相连的碳原子的支化度)与脂肪醇的溶解度、辛醇/水分配系数、急性生物毒性、蒸发热、摩尔磁化率关联,复相关系数分别为0.9955,0.9951,0.9941,0.9964,0.9968,优于文献.同时与脂肪醇的气相色谱保留指数也相关得很好,相关系数为0.9956.结果表明,Te指数可用于醇多种理化性质和生物活性的预测.     

一株枯草芽孢杆菌分离鉴定及其降解稠油特性

以稠油为唯一碳源,从被稠油污染过的土壤中筛选到一株高效石油烃降解茵,经生理生化鉴定和16S rDNA鉴定确认其为枯草芽孢杆茵.在摇瓶实验中,该菌最佳降解温度为35～45℃,最佳pH值为7.5～8.5,最佳盐质量浓度为8～16 g/L.在最佳降解条件下,当油质量浓度为0.1 g/L时,稠油降解率达34.3%.利用GC-nD分析知,该茵主要降解稠油中n-C9～n-C40的烷烃组分;利用GC-MS分析得知,该茵对蔡及烷基化萘去除彻底,对二苯并噻吩、芴和稠二萘等部分芳烃类化合物有降解作用,在稠油降解过程中菲及菲的衍生物有所增加.     

Effect of Cooling Rate on the Solidification Behavior and Microstructure of SiC_w/Al-18Si Composites

Al-18Si alloy reinforced with 15%,20% and 25%(volume fraction) SiC whiskers were prepared by squeeze casting technique and the solidification behavior and microstructure of as-prepared composites at different cooling rates were studied by DSC,optical microscope,SEM and TEM.The results show that silicon phase is nucleated on SiC whiskers.With the increase of cooling rate,the degree of undercooling increases in the composites as well as in the alloys.The increase of cooling rate leads to a reduction in the size of eutectic Al-Si and also changes its morphology from short stick to equiaxed.However,the change of primary Si is complex.The primary Si size is refined,and then coarsened with increasing cooling rate.The primary Si morphology of composites changes from agglomerate to stick.     

DLR/HIT多指机器人灵巧手的研究

基于机电一体化设计理念和集成化、模块化设计方法研制了DLR/HIT灵巧手,DLR/HIT灵巧手具有4个相同结构的模块化手指,共具有13个自由度,具有拟人手形的外观.采用商品化的直流无刷电机实现了手指的驱动;手指具有位置、力/力矩及温度等多种感知能力;基于DSP/FPGA等实现了手指的通讯和实时控制;高度集成,将所有部件均集成在手指和手掌内.DLR/HIT手具有很好的可靠性、可操作性和精细操作能力.     

电磁污染控制用S带吸波粉煤灰板材的制备

报道了根据λ/4型电磁波吸收原理,通过理论设计和模拟分析,以电厂废渣粉煤灰为介电材料,通过电阻膜复合,成功制备出新型粉煤灰吸波板材.实验表明,电阻膜的电阻为356Ω/□(方块电阻),厚度1.5 cm的粉煤灰板试样在S带(2~4 GHz),-10 dB吸收带宽达到60%以上,在2.9 GHz,最大吸收为-25 dB,新材料可用于室内电磁环境的改善和污染控制,并为粉煤灰的利用提供了新的高附加值途径.     

机械合金化法制备W-Cu合金粉末的研究

将W80Cu20（n（W）：n（Cu）=4：1）混合粉末在QM-BP式行星式高能球磨机中球磨进行机械合金化,研究了不同球磨时间对W-Cu混合粉末组织的影响.采用XRD和SEM对不同球磨时间的粉末进行分析,结果显示随着球磨时间的增加,混合粉末产生合金化效果不断增强,Cu固溶于W中,并且晶粒尺寸得到一定的细化.     

Processing and properties of 2D SiC/SiC composites by precursor infiltration and pyrolysis

Two-dimensional plain-weave silicon carbide fiber fabric reinforced silicon carbide (2D-SiC/SiC) composites were molded by stacking method and densified through precursor infiltration and pyrolysis (PIP) process. SiC coating was deposited as the fiber/matrix interphase layer by chemical vapor deposition (CVD) technique. Fiber/matrix debonding and relatively long fiber pullouts were observed on the fracture surfaces. Additionally, the flexural strength and elastic modulus of the composites with and without fiber/matrix interphase layer were investigated using three-point bending test and single-edge notched beam test. The results show that the fiber fraction and the porosity of 2D-SiC/SiC composites with and without coating are 27.2% (volume fraction) and 11.1%, and 40.7% (volume fraction) and 7.5%, respectively. And the flexural strength and elastic modulus of 2D-SiC/SiC composites with and without coating are 363.3 MPa and 127.8 GPa, and 180.2 MPa and 97.2 GPa, respectively. With a proper thickness, the coating can effectively adjust the fiber/matrix interface, thus causing a dramatic increase in the mechanical properties of the composites. Foundation item: Project(NCET-07-0228) support by the New Century Excellent Talents in University     

Zn掺杂对GdMnO体系的晶体结构影响

系统研究了Gd（1-x）ZnxMnO3（x=0,0.2,0.4,0.6,0.8,1.0）体系的结构。结果表明,实验样品具有正交对称性结构。当Zn掺杂浓度x≤0.4时,随着Zn掺杂浓度的增加,晶格常数b、c减小,而晶格常数a增大,晶胞体积逐渐减小;当掺杂浓度x≥0.6时,Zn掺杂浓度的增加,晶格常数b、c增大,而晶格常数a减小,晶胞体积逐渐增大。计算表明Gd（1-x）ZnxMnO3系列化合物的容忍因子在0.76~0.92范围,可以形成稳定的钙钛矿结构。     

复合掺杂Nd（III）和Zn（II）非晶态Ni（OH）2电极活性材料的制备及其表征

以NiSO4、ZnSO4和Nd（NO3）3为原料,采用共沉淀快速冷冻法制备出了复合掺杂稀土Nd（III）和Zn（II）的非晶态氢氧化镍粉体材料。测试发现：样品材料微结构无序性强,结晶水含量较高。将样品材料制备成镍电极并组装成MH—Ni电池,在80mA／g恒电流充电5．5h、40mA／g恒电流放电、终止电压为1．0V的充放电制度下,复合掺杂6％Nd（III）和6％Zn（II）样品材料电池的放电平台为1．2624V,放电比容量为343．12mAh／g,远高于目前应用的B-Ni（OH）2电极活性材料的放电比容量。