盖层封闭能力的灰聚类评价方法

提出灰聚类评价方法，用于盖层封闭能力定量评价。所有被评价对象构成聚类对象集，所有评价指标构成评价指标集，所划分的盖层封闭能力等级构成聚类的灰类集，按照最大聚类权确定对象所属的灰类，即盖层的封闭能力级别。评价流程是：确定指标灰类模式→数据预处理→利用聚类公式计算→利用最大聚类权准则抉择。这种方法避免了加法评分法要依靠人的主观经验划定总评分值的问题，而且由于把评价对象视为“灰”的，具有处理边缘信息的能力。以琼东南盆地３个主要探区的盖层封闭性评价为例，介绍了灰聚类评价的具体应用方法。灰聚类评价方法同样可用于储集层评价、圈闭评价等地质问题的定量研究。表２参３（王孝陵摘     

Interdiffusion behavior of Hg in HgTe/CdTe superlattices grown on Cd0.96Zn0.04 Te (211)B substrates by molecular beam epitaxy

Double-crystal x-ray rocking curve (DCRC) and secondary-ion mass-spectroscopy (SIMS) measurements have been performed to investigate the effect of rapid thermal annealing on the interdiffusion behavior of Hg in HgTe/CdTe superlattices grown on Cd_0.96Zn_0.04Te (211)B substrates by molecular beam epitaxy. The sharp satellite peaks of the DCRC measurements on a 100-period HgTe/CdTe (100Å/100Å) superlattice show a periodic arrangement of the superlattice with high-quality interfaces. The negative direction of the entropy change obtained from the diffusion coefficients as a function of the reciprocal of the temperature after RTA indicates that the Hg diffusion for the annealed HgTe/CdTe superlattice is caused by an interstitial mechanism. The Cd and the Hg concentration profiles near the annealed HgTe/CdTe superlattice interfaces, as measured by SIMS, show a nonlinear behavior for Hg, originating from the interstitial diffusion mechanism of the Hg composition. These results indicate that a nonlinear interdiffusion behavior is dominant for HgTe/CdTe superlattices annealed at 190°C and that the rectangular shape of HgTe/CdTe superlattices may change to a parabolic shape because of the intermixing of Hg and Cd due to the thermal treatment.     

起重机吊钩拖动绕线电动机他励双高调速系统

本文提出励磁电流可自动控制的他励式双高调速系统设计方案。系统在提升特别是在下放重物时，具有较硬的机械性；在负载１０－１００％的变化范围内，可实现最大偏差Δｎｍａｘ／ｎｍｉｎ１００％≤１０％，调速范围Ｄ≥１０；在满载运行条件下，可节约电能８０％以上。     

具有再生反馈雷达的角跟踪性能闭环测试

本文论述了用雷达跟踪目标最大角速度和角加速表征具有再生反馈雷达角跟踪性能的合理性,并论述了用单片机测试雷达跟踪目标最大角速度和最大角加速的方法。     

凸轮机构基圆半径的确定方法及其分析

基圆半径的确定方法，除了用图解法和试算法外，还可用解析法和图解分析法求解。４种方法各有优缺点，设计时要根据具体情况选择。     

高功率激光器的光束质量及其对激光加工的影响

本文介绍了光束的模式、评价光束质量的几种方法,着重介绍了国际标准化组织(ISO)提出的光束传输系数M作为评价光束质量的方法。文中还讨论了光束质量对焊接、切割加工的影响;热透镜效应对加工的影响等。     

海上靶场角度量录取系统的研制

本文详细叙述了海上靶场角度量录取糸统的组成、测试原理及其功能设计，简要介绍了该系统在靶扬的应用情况．     

Numerical study on PEMFC’s geometrical parameters under different humidifying conditions

Steady-state and three-dimensional simulations were carried out to study the influences of geometrical parameters on the performance of PEMFC under different hydrating conditions. Flow fields, species transport, transport of water in polymer membrane and movement of liquid water in cathode and anode porous layers were determined, in order to accomplish a complete estimation of ohmic and concentration losses of PEMFC power. The geometrical parameters were thickness of the polymer membrane, cathode catalyst layer as well as gas channel to rib width ratio. Every simulation was made under different relative humidities of inlet flows (50 and 100%) for every change of characteristic length. Results show that the influence of the geometrical parameters on ohmic and concentration losses is of considerable importance. The performance of PEMFC is seriously affected under dehydrating conditions. However, such performance may be considerably improved by using suitable geometrical parameters. Cathode and anode liquid saturation may not only affect the transport of species, but also the polymer electrolyte water content. These results show the importance of simultaneously calculating both the water absorption and desorption through the polymer electrolyte and the liquid saturation in the cathode and anode porous mediums to obtain an actual view of ohmic and concentration losses of the PEMFC performance.     

高效防气防砂一体化管柱的研制与应用

为解决文南油田高气液比井出砂易造成卡泵的问题,研制了高效防气防砂一体化管柱。该管柱主要由闭式气锚、重力式防气装置和激光割缝筛管3部分组成。闭式气锚的分离作用消除了气体对抽油泵的影响,提高了泵效;重力防气装置利用液气分离原理和高烟囱原理进行液气分离,液流回流时间可达10min,排气最高压差可达0.2MPa;经激光割缝筛管过滤后的液体含砂粒外径小于0.05mm。该管柱在文南油田现场应用16井次,累计增液6000t,增油2717t,平均单井泵效提高7%。     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.