Behaviors of concrete-filled steel tubular members subjected to combined loading

The present study is an investigation on the behaviors of concrete-filled thin-walled steel tubular members subjected to combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. ABAQUS software is used in this paper for the finite element analysis (FEA). A comparison of results calculated using this modeling shows generally good agreement with test results. The FEA modeling is then used to investigate the influence of important parameters that determine the ultimate strength of the composite members under combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. The parametric studies provide information for the development of formulae for calculating the ultimate strength of the composite members subjected to combined loading.     

Structural properties of phosphorous-doped polycrystalline silicon

The structural properties and hydrogen bonding of undoped and phosphorous doped polycrystalline silicon produced by step-by-step laser dehydrogenation and crystallization technique were investigated using Raman spectroscopy and hydrogen effusion measurements. At low laser fluences, E_L, a two-layer system is created. This is accompanied by the change in hydrogen bonding. The intensity of the Si–H vibration mode at 2000 decreases faster than the one at 2100 cm⁻¹. This is even more pronounced in phosphorous-doped specimens. The laser crystallization results in an increase of the hydrogen binding energy by approximately 0.2–0.3 eV compared to the amorphous starting materials.     

Clay compaction modelling by homogenization theory

The modelling of hydromechanical behavior of clayey sediments by homogenization theory is described. The rheological model of clays buried in depth requires a three-dimensional approach and laboratory experiments to quantify the model parameters. An iterative process which can be coupled to any homogenization method is used to model the porous media behavior. Hydromechanical compaction results from oedometric experiments are simulated with the proposed model.     

Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

On the binomial confidence interval and probabilistic robust control

The Clopper-Pearson confidence interval has ever been documented as an exact approach in some statistics literature. More recently, such approach of interval estimation has been introduced to probabilistic control theory and has been referred as non-conservative in control community. In this note, we clarify the fact that the so-called exact approach is actually conservative. In particular, we derive analytic results demonstrating the extent of conservatism in the context of probabilistic robustness analysis. This investigation encourages seeking better methods of confidence interval construction for robust control purpose.     

Sol-Gel Preparation of LaNiO3 and Its Physical and Chemical Properties

LaNiO3 was synthesized by sol-gel method in which lanthanum nitrate and nickel nitrate were used as start materials and citric acid was used as complex for gel formation.The precursor was dried and subsequently heated at elevated temperature to form the desired product.XRD analysis shows that pure LaNiO3 was synthesized.Electrical conductivity and electrochemical performance of the material were tested.The electrical conductivity decreases from 34.5that there are current peaks in the curve, which is the evidence of the electrochemical activity of LaNiO3.     

直流法测量钯氢化物电极电阻时的阻值偏移

讨论了直流法在线测量钯氢化物电极电阻时的电化学效应，计算了电解液的共导、测量电流与电解电流引起的浓差电池效应以及电极作为集流体引起的电阻贡献。结果表明：当电极具有高的长度与半径比值、粗糙的表面、高的溶液电导以及大的电解电流时容易引起显著的附加电阻。     

Three dimensional boundary element analysis of internal cracks under sliding contact load with a spherical indenter

Using boundary element based three dimensional modelling for linear fracture mechanics, we present an analysis of cracking in a homogeneous medium subject to contact load. The proposed iterative solution procedure allows a simultaneous treatment of a reasonable number of partially closed cracks. It is shown that the most probable direction of propagation of a vertical internal crack is strongly dependent on its size compared to the contact radius and its location with respect to the axis of maximum normal load.     

A p‐version,first order shear deformation,finite element for geometrically non‐linear vibration of curved beams

A p‐version, hierarchical finite element for curved, moderately thick, elastic and isotropic beams is introduced. The convergence properties of the element are analysed and some results are compared with results published elsewhere or calculated using a commercial finite element package. It is verified that, with the proposed element, shear locking does not affect the computation of the natural frequencies and that low dimensional, accurate models are obtainable. Geometrically non‐linear vibrations due to finite deformations, which occur for harmonic excitations with frequencies close to the first three natural frequencies of vibration, are investigated using Newmark's method. The influence of the thickness, longitudinal inertia and curvature radius on the dynamic behaviour of curved beams are studied. Copyright © 2004 John Wiley & Sons, Ltd.     

A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.