Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

Synthesis and structural characterization of methacrylic acid/octadecyl acrylate‐graft‐poly(methylhydrosiloxane) by hydrosilylation

Methylmethacrylate (MMA) and octadecyl acrylate (OA) were grafted to poly(methylhydrosiloxane) (PMHS) by hydrosilylation, respectively, with hexachloroplatinic acid as catalyst, and the former was further hydrolyzed to prepare methacrylic acid (MAA)‐graft‐PMHS under the alkaline condition. Through orthogonal experiment, main factors affecting the graft reaction between OA and PMHS were discussed and arranged in a decreasing order according to their abilities of the effect on the hydrosilylation of OA with PMHS: catalyst dosage, reaction temperature, reaction time, material ratio, and solvent dosage. It was found that the hydrosilylation of OA with PMHS was easier to that of MMA with PMHS. Under optimal conditions, the grafting ratios of MMA with PMHS and OA with PMHS reached about 90 and 95%, respectively. FTIR and ¹H NMR spectra indicated that the hydrosilylation reactions followed the Markovnikov's rule and played a strong preference toward β‐1,2‐addition. The test of contact angle indicated that surface energy of a system was mainly dependent on the polar groups. The surface energy of OA‐graft‐PMHS (35.07 mN/m) was similar to those of PMHS (35.62 mN/m) and polyoctadecyl acrylate (36.57 mN/m), and lower than that of MAA‐graft‐PMHS (43.50 mN/m). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Maghnite‐H+, a solid catalyst for the cationic polymerization of α‐methylstyrene

The polymerization of α‐methylstyrene (AMS) catalyzed by Maghnite‐H⁺ (Mag‐H) was investigated. Mag‐H is a montmorillonite sheet silicate clay, exchanged with protons. It was found that the cationic polymerization of AMS is initiated by Mag‐H at ambient temperature in bulk and in solution. The effect of the amount of Mag‐H, the temperature, and the solvent was studied. The polymerization rate increased with increase in the temperature and the proportion of catalyst, and it was larger in nonpolar solvents. These results indicated the cationic nature of the polymerization. It may be suggested that the polymerization is initiated by proton addition to monomer from Mag‐H. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

橡胶Mooney—Rivlin模型材料系数对轴向刚度影响分析

在橡胶小变形范围内，采用理论推断的方法，得到在相同硬度下橡胶Mooney—Rivlin模型材料系数由C2／C1决定的关系式。并采用ABAQUS有限元软件分析的方法，结合橡胶轴向刚度常规解，分析了C2／C1不同值对橡胶轴向刚度的影响进行，结果显示其影响呈现一定规律性。     

Tribological behavior of PTFE nanocomposite films reinforced with carbon nanoparticles

Carbon-based nanoparticles synthesized by heat treatment of nanodiamond in the temperature range of 1000–1900 °C were added to PTFE film to investigate the structural effect of the carbon particles on the tribological properties of PTFE composite film. Carbon-based nanoparticles were prepared by milling with micron sized beads in chemically treated water before their addition to PTFE film. The wear and frictional properties of PTFE nanocomposite film were measured by the ball on plate type wear test. The wear resistance of PTFE film was found to be enhanced by the addition of 2 wt% of carbon nanoparticles. The wear coefficient of PTFE film was decreased from 16.2 to 3.5 × 10⁻⁶ mm³/N m by the addition of carbon-based nanoparticles heat-treated at 1000 °C. Increasing the heating temperature of the nanodiamonds caused the extent of aggregation and particle size to increase. The wear resistance of PTFE nanocomposite film was enhanced by the addition of nanodiamonds heat-treated at 1000 °C, but decreased when the heat treatment temperature of carbon nanoparticles was further increased. Tribological behavior of PTFE nanocomposite films depending on the types of carbon nanoparticles were explained based on the structural, physical and chemical modification of carbon nanoparticles.     

Study of the effective parameters on mechanical and electrical properties of carbon black filled PP/PA6 microfibrillar composites

In this study the electrical and mechanical properties of microfibrillar polypropylene (PP)/polyamide6 (PA6) blend filled with super conductive carbon black (CB) have been investigated. In situ microfibrillar PP/PA6 composites filled with CB are produced using a single screw extruder equipped with a spinneret. Glycidyl methacrylate (GMA) grafted polypropylene (PP-g-GMA) is used as the compatibilizer. To investigate the effects of extensional flow on the microstructure, electrical and mechanical properties, three adaptors with various convergence angles were designed, prepared and applied between the extruder and the spinneret. To optimize the effects of processing and material parameters on the electrical and mechanical properties, the Taguchi method of experimental design is used. Material and processing factors which are studied include: concentration of PA6, compatibilizer level, CB concentration, drawing speed of melt spinning line, adaptor angle, order of mixing and temperature profile along the extruder. The results show an increase in DC conductivity of up to 10¹¹ times in comparison with pure PA6, by increasing the concentration of CB, drawing speed, adaptor angle and optimizing other parameters. By optimizing processing and material factors studied here, strength of microfibrillar structured composites is increased of up to 80% in comparison to pure PP.     

CDMA2000 1xEV-DO中的分组调度算法

移动通信系统需要更好地支持分组数据业务，并满足高速分组数据业务的服务质置要求。这可以通过采用好的调度算法提高平均业务速率和系统整体稳定性实现。针对CDMA2000 1x EV-DO系统的有代表性的调度算法有3种：正比公平算法、速率受限的最大载干比算法、加权公平排队-正比公平（WFQ-PF）联合算法。正比公平调度算法是一种算法简单实用的调度方案，但不能满足用户的服务质景保证；速率受限的最大载干比算法具有比正比公平算法更高的平均吞吐量，可方便地在吞吐量和公平性之间获得很好的折衷；WFQ-PF联合算法具有良好的综合性能，但算法较复杂。     

3-N-丙酰基-2-芳基-5-(3-碘苯基)-1,3,4-(口恶)唑啉类化合物的合成及表征

以3-碘苯甲酸为原料,在浓硫酸作用下与乙醇反应制得3-碘苯甲酸乙酯(1),再以无水乙醇为溶剂,在105℃化合物1与80％的水合肼反应8 h,制得3-碘苯甲酰肼(2)。在无水乙醇中,在90～95℃化合物2分别与4-甲基苯甲醛、2-氯苯甲醛、4-氯苯甲醛、4-羟基苯甲醛、2,4-二氯苯甲醛、4-甲氧基苯甲醛、3-硝基苯甲醛、4-硝基苯甲醛和4-二甲氨基苯甲醛反应得到相应的酰腙[3(a～i)]。最后化合物3(a～i)分别与丙酸酐脱水环化成了3-N-丙酰基-2-芳基-5-(3-碘苯基)-1,3,4-(口恶)唑啉类化合物[4(a～i)],收率分别为86．2％,70．5％, 80．1％,68．2％,62．4％,75．2％,73．2％,70．5％和63．2％。并通过元素分析,IR,1H NMR和MS对化合物4(a～i)的结构进行了表征。     

Accelerator Analysis of Tributyltin Adsorbed onto the Surface of a Tributyltin Resistant Marine Pseudoalteromonas sp. Cell

Tributyltin (TBT) released into seawater from ship hulls is a stable marine pollutant and obviously remains in marine environments. We isolated a TBT resistant marine Pseudoalteromonas sp. TBT1 from sediment of a ship’s ballast water. The isolate (10^{9.3 ± 0.2} colony-forming units mL⁻¹) adsorbed TBT in proportion to the concentrations of TBTCl externally added up to 3 mM, where the number of TBT adsorbed by a single cell was estimated to be 10^8.2. The value was reduced to about one-fifth when the lysozyme-treated cells were used. The surface of ethanol treated cells became rough, but the capacity of TBT adsorption was the same as that for native cells. These results indicate that the function of the cell surface, rather than that structure, plays an important role to the adsorption of TBT. The adsorption state of TBT seems to be multi-layer when the number of more than 10^6.8 TBT molecules is adsorbed by a single cell.     

Mapping surface temperature in large lakes with MODIS data

Satellite sensor MODIS on two platforms can produce Sea Surface Temperature over certain regions about three to four times per day. Our objective was to test if the MODIS SST product can be applied for lakes whose surface areas are large enough to be observed at the MODIS spatial resolution and to compare the satellite-derived lake surface temperatures with in situ measurements. Surface temperatures for Lakes Vänern and Vättern in Sweden, two of the largest European lakes, are extracted from the MODIS/Terra images for period 2001-2003. The results are analyzed on different quality levels, as all MODIS L2 products are equipped with an additional quality flag. We present temperature development over 2001-2003, and show the capability of the MODIS SST product to couple the known thermodynamical features in the lakes under study, where temperature varies greatly with space and time. These results can complement lake monitoring programs anywhere.