Differences in the structure of copper active sites for decomposition and selective reduction of nitric oxide with hydrocarbons and ammonia

Cu ion co-ordination-location in zeolites of MFI, erionite, mordenite matrices has been determined and the activity of the individual Cu sites compared for NO decomposition and its selective reduction by hydrocarbons or ammonia. It appears that Cu ions in the vicinity of one framework Al (site II), able to form stable Cu⁺-dinitrosyl complexes, and abundant in MFI structure, are responsible for high activity in NO decomposition. The Cu ions neighbouring two framework Al atoms (site I), and forming mostly mononitrosyl complexes, which dominate in erionite structure, provide a high activity in selective reduction of NO.     

活性炭载体的超声波处理对Pt／C催化剂活性的影响分析

通过对活性炭载体进行不同条件的超声波处理获得了具有不同表面化学性质的载体，使用比表面积（BET）、酸碱滴定等技术手段对载体的物理化学性质进行了表征。将经过超声波处理的活性炭载体制备成Pt／C催化剂，并将催化剂直接用于催化反应，考察了活性炭载体的不同超声波处理条件对Pt／C催化剂性能的影响。实验发现，活性炭载体经过超声波处理后，表面灰分含量、pH值和中孔孔容有较大的变化；使用经过60min超声波处理后中孔孔容较大的活性炭作为载体制备的Pt／C催化剂，在催化加氢反应性能测试中显示了最高的催化活性。在此基础上，就活性炭载体的超声波处理对Pt／C催化剂活性的影响进行了讨论。     

Single and combined deactivating effect of alkali metals and HCl on commercial SCR catalysts

Two commercial SCR catalysts, with a nominal W content of about 9 wt.% and a V nominal content of 0.55 and 1.8 wt.%, respectively, were contacted with different amounts of Na and K and with HCl vapours in order to simulate poisoning by species more specifically contained in exhaust gases from MSW combustion. Catalysts were characterised using XRD analysis, SEM/EDX analysis, BET and pore size distribution measurements, NH₃ TPD, TG analysis. Poisoning agents do not cause loss of surface area nor pore occlusion. A significant loss of surface acidity was observed upon alkali metals poisoning whereas a decreasing of vanadium content was observed for the more concentrated catalysts upon HCl poisoning. Catalysts deactivation is proportional to the number of acid sites neutralised by alkali metals adsorbing ammonia in the temperature range typical of SCR process. HCl promotes the formation of new acid sites showing a lower activity compared to the original one.     

重油催化裂化反应技术的新进展

近十几年来，重油催化裂化技术作为主要的重质油轻质化手段得到了迅速发展，国内外围绕催化裂化装置的提升管反应器也开发了许多新技术。综述了重油催化裂化反应技术的新进展，并对新技术的开发进行了讨论。     

从废钼合金催化剂中提取钼等有价元素方法的研究

ＭｏＣｏＮｉ合金料首先氧化焙烧碱浸出，滤饼再加纯碱焙烧水浸出使钼与钴镍分离，最后用萃取法分离钴镍的工艺流程，对废钼合金催化剂进行了综合回收。采用该工艺流程和生产线分别生产出合格的工业级钼酸钠、氧化钴和氧化镍。     

Zirconium-based intermetallics as heterogeneous catalysts for the fischer-tropsch reaction: I. Zr-Ni-Co catalysts

Alloys of the general formula Zr₅₀Ni_xCO_50-x, where 0 ≦x≧ 50, have been prepared and used in the temperature range 300–400°C, in the pressure range 1–9 barg in a microtubular reactor for the reaction of hydrogen with carbon monoxide to give hydrocarbons. The alloys or intermetallic materials were prepared by argon arc melting, powdered by hydrogen decrepitation and characterised by means of optical microscopy (metallography), scanning electron microscopy with surface analysis and magnetic susceptibility measurements. The selectivity towards higher hydrocarbons increased with (i) increase in the total pressure and (ii) decrease in hydrogen content of the feed gases. The kinetics were found to be of the form: where m = 1.0 ± 0.2 and n = 0. The apparent energy of activation (E_a) lay in the range of 80–130 kJ mole^?1 and there appeared to be a compensation effect between E_a and the pre-exponential factor A. The turnover numbers for the reaction exhibited an activity maximum for alloys of composition around Zr₅₀Ni₄₀Co₂₀ and Zr₅₀Ni₃₀Co₂₀. Magnetic susceptibility measurements indicated that alloys changed their nature from moderately paramagnetic to strongly paramagnetic or even ferromagnetic after use and this is attributed to the conversion of zirconium to zirconium oxide during reaction with the attendant production of free 3d-transition metals. Derived catalysts prepared by air treatment of the hydrogen-decrepitated intermetallics behaved almost identically to the latter materials and gave similar magnetic susceptibility values to used hydrided materials.     

Accelerated sintering of PtRh/Al2O3 catalysts in an oxygen periodic pulse flow

PtRh catalysts were prepared by coimpregnation, with chlorine-free precursors of a -alumina. They were sintered at 973 K under a continuous flow of O₂ (1% in Ar or air) or of a flow of Ar into which pulses of O₂ were injected periodically. Under the latter conditions the sintering was significantly accelerated, particularly for a certain value of the period of O₂ pulses.     

Photocatalytic performance of Fe-substituted ZnAl2O4 powders under sunlight irradiation on degradation of industrial dyes

Using the sol–gel auto combustion method with diethanolamine (DEA) as fuel, a sequence of iron-substituted zinc aluminates, ZnFe_xAl_2-xO₄ powders, including variable Fe³⁺ ion concentrations (0 ≤ x ≤ 2) were effectively prepared. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), the Brunauer–Emmett–Teller (BET) method, UV–visible diffuse reflectance spectroscopy (UV-DRS), and vibrating sample magnetometer (VSM) were employed to examine the structures, chemical bonds, morphologies, composition, surface area, and optical properties as well as the magnetic behavior of the obtained samples. A single-phase spinel structure was obtained for the calcined aluminate powders with different interplanar spacing and crystallite sizes, as revealed by the classification results. The bandgap energy (E_g) of adapted aluminates was in the range of 2.04-3.14 eV, identified as being much lower compared to the pure sample (5.60 eV). Thus, Fe³⁺-substituted ZnAl₂O₄ samples could be successfully photoexcited using both ultraviolet and visible light, as suggested by the results. Examination of how the four main pollutant types decay when irradiated by sunlight was carried out to assess the samples and establish photocatalytic activity. These contaminants included rhodamine B (RhB), methylene blue (MB), methyl orange (MO), and methyl red (MR). The performance of photocatalytic degradation reached 98% after 150 min for all optimal samples of organic dyes. Besides, each of the altered photocatalysts could be recycled and displayed high stability. The S-shaped curve of ferrimagnetism can result in those samples as found by the magnetic measurements, though pure ZnAl₂O₄ displays diamagnetic characteristics. The adapted samples show intense improvement in the remanent magnetization (M_r) when compared to pure ZnAl₂O₄, signifying that magnetic photocatalyst recovery by applying an external magnetic field is easy. Thus, these results offer a convincing sign that ZnAl₂O₄ powders replaced by Fe³⁺ could provide the ability to aid in the ecologically friendly collection of solar energy.     

DMFC阳极催化剂用GRQD-NiCo2O4复合物的制备与电催化活性分析

采用水热法制备GRQD-NiCo₂O₄复合物,利用XRD、SEM及TEM分析其微结构,并探讨其作为DMFC阳极催化剂使用时的电化学性能。微结构分析表明所得GRQD-NiCo₂O₄复合物皆为具NiCo₂O₄单一相的尖晶石结构,且GRQD质量浓度高于0.25 g/mL后表面形貌将转变GRQD与NiCo₂O₄相互结合的状态。电化学分析表明添加GRQD可有效增强NiCo₂O₄的导电性并提升其电化学稳定性,其中GRQD质量浓度为0.25 g/mL时所得样品经500次循环测试后电流密度约为77.5 A/g,与循环5次后相比其电流密度剩余量最大（约为69.7%）,该样品作为DMFC阳极催化剂使用时性价比最佳。     

日本超高温结构用金属材料的研究现状

简要介绍了日本围绕燃气轮机用关键超高温金属结构材料所展开的研究开发工作,包括Ni基超合金、耐热金属间化合物、Nb基超合金及其复合材料。Ni基超合金仍是当前燃气轮机用超高温结构的主要材料,但其使用温度的上升潜力已经不多,用新的超高温材料替代Ni基超合金是燃气轮机用材的发展趋势,金属材料中耐热金属间化合物和Nb基复合材料是今后关注的焦点。