中频炉酸性炉衬使用寿命的探讨

通过对炉衬材料的选择,作用机理及影响石英砂炉衬材料寿命的相关因素的阐述,说明了SD-T-A石英砂干振料可提高中频炉酸性炉衬使用寿命的原因.     

Na2B4O7对镁合金旧料组织和性能的影响

利用等离子发射光谱仪、电镜、X衍射、万能材料试验机、腐蚀试验等手段研究了不同Na2B4O7含量的熔剂对镁合金废旧料的力学性能、相组成、断口形貌以及腐蚀行为的影响.研究表明,使用含Na2B4O7的熔剂可以使镁合金旧料中Fe的质量分数降低到0.004%以下,同时提高材料的抗拉强度和伸长率.腐蚀试验表明含Na2B4O7的质量分数为20%的熔剂可以使材料的腐蚀速率从15.1 mg*cm-2*d-1降低到0.4 mg*cm-2*d-1.电镜观察和X衍射表明,净化处理对断口形貌和相组成没有明显影响.最后分析了Na2B4O7除铁的机理,认为Fe与B形成某种化合物沉淀下来是主要原因.     

合金元素对Fe_3Al和FeAl合金力学性能的影响SCIEI

本文研究了Mo,Si,B和化学计量成分对Fe_3Al和FeAl合金室温和高温拉伸性能以及组织结构的影响,结果表明,三种合金元素都使两种铁铝化物得到明显强化,但Mo和Si使其严重变脆,硼使FeAl增加塑性,断口由沿晶型变为穿晶准解理型。富Al的Fe_3Al和富Fe的FeAl合金室温塑性较化学计量化合物有明显提高。Fe_3Al从400—550℃,FeAl从400—500℃出现反常温度关系,用组织结构方面的结果对此进行了讨论。     

基于人工神经网络的结构钢回火后力学性能预测

利用多层前向神经网络，使用B－P算法对结构钢回火性能预测进行了研究。通过利用99种钢450余组训练数据样本对神经网络进行训练，建立了结构钢回火后的力学性能与金属成分和回火温度之间的隐性函数。并针对训练用样本不足的问题，设计了为网络提供自学功能软件，在钢完全淬透的前提下，用此神经网络模型可在一定精度范围内预测结构钢的回火力学性能。     

AlF3贮仓料位计在线监控系统开发与应用

针对铝电解原材料中AlF3与Al2O3自动配料不准和难于观察及控制的现象，我厂开发应用了AlF3贮仓料位计，并与微机网络相连，实现了远程测量与在线监控，使AlF3配料更准确更均匀，电解质分子比更稳定，电解槽生产低耗高效。     

深过冷Fe76B12Si12超细晶材料的凝固组织与软磁性能

首次采用深过冷加水淬的方法,成功地制备了直径为16 mm的样品,高为15 mm,组织中颗粒平均尺寸约为120nm左右的Fe76B12Si12合金超细晶材料.其磁损耗P1T400和P1T1000分别为普通硅钢片的40%和65%.系统研究了组织类型及Fe2B(Si)相尺度对该合金软磁性能的影响,发现该合金的最佳软磁性能位于Fe2B(Si)相完全粒化的非规则共晶组织区,并且当Fe2B(Si)相尺寸细化至0.36～0.50μm时,其软磁性能随着相尺寸的减小而大幅度改善.对以上结果产生的原因进行了讨论.     

Effects of CeF3 on properties of self-shielded flux cored wire

0 IntroductionSelf-shielded flux cored wire is a newly developedwelding material used without gas protection. Use of suchcored wires has grown rapidly in developed countriesbecause of the following advantages: simple use, goodwind resistance ability, lower cost resulted from highproductivity and strong desulfurization ability[1]. Self-shielded flux cored wires are preferred for on-site weldingsuch as ship and barge building, storage tank, bridge,offshore oil platform buildings and so on[2 -3].…     

Experiment and simulation study of 3D magnetic field sensing for magnetic flux leakage defect characterisation

Magnetic flux leakage (MFL) testing is widely used to detect and characterise defects in pipelines, rail tracks and other structures. The measurement of the two field components perpendicular to the test surface and parallel to the applied field in MFL systems is well established. However, it is rarely effective when the shapes of the specimens and defects with respect to the applied field are arbitrary. In order to overcome the pitfalls of traditional MFL measurement, measurement of the three-dimensional (3D) magnetic field is proposed. The study is undertaken using extensive finite element analysis (FEA) focussing on the 3D distribution of magnetic fields for defect characterisation and employing a high sensitivity 3-axis magnetic field sensor in experimental study. Several MFL tests were undertaken on steel samples, including a section of rail track. The experimental and FEA test results show that data from not only the x- and z-axes but also y-axis can give comprehensive positional information about defects in terms of shape and orientation, being especially advantageous where the defect is aligned close to parallel to the applied field. The work concludes that 3D magnetic field sensing could be used to improve the defect characterisation capabilities of existing MFL systems, especially where defects have irregular geometries.     

AB INITIO CALCULATION OF THE ELASTIC AND OPTICAL PROPERTIES OF Al_3Sc COMPOUND

The ab initio method has been performed to explore the elastic and optical properties of Al3Sc compound, based on a plane wave pseudopotential method. It can be seen that the calculated equilibrium lattice parameter and elastic constants are in reasonable agreement with the previous experimental data. The elastic constants satisfy the requirement for mechanical stability in the cubic structure of the Al3Sc compound. The optical property calculations show that a strong absorptive peak exists from 0-15eV and a relative small absorptive peak exists around 30eV. The form is caused by the optical transitions between high s, p, and d bands, and the latter results from the optical transitions from high s, p, and d bands to the low 2p band.     

基于B/S模式的CAPP制造资源管理系统的实现

许多企业内部建有Internet／Intranet网来加强企业内部的信息集成和共享。顺应这一趋势，文章提出了基于B／S模式的CAPP制造资源管理系统，利用网络编程语言VBScript实现制造资源的共享。文章首先通过和C／S模式比较，概述了B／S模式的优势，并建立了适合于动态变化环境的制造资源模型。最后结合应用实例探讨了利用ASP、ADO、SQL和ODBC技术实现制造资源的远程知识查询的理论和方法。